Home › Engine / Hybrid System › 1HZ (LUBRICATION) › OIL PUMP
RM25T0E _51 Engine / Hybrid System _029209 1HZ LUBRICATION _0134030 OIL PUMP A

1HZ LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301 1.INSTALL TIMING GEAR CASE SUB-ASSEMBLY

a.

Remove any old seal packing (FIPG material) from the timing gear case sub-assembly and cylinder block sub-assembly.


b.
A326419C01
0.333,1.75 1.24,1.75 true 0.177,1.646 0.49,1.802 0.313,0.156 10 false *a 2.01,0.135 2.323,0.292 0.313,0.156 10 false *b 2.771,0.135 3.083,0.292 0.313,0.156 10 false *c
*a Seal Packing
*b CORRECT
*c INCORRECT


Apply seal packing to the places shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 to 10 mm (0.158 to 0.394 in.)


NOTICE:

After applying seal packing, install the timing gear case sub-assembly within 5 minutes and tighten the bolts within 15 minutes.



c.
A326420

Install a new gasket to the groove of the timing gear case sub-assembly as shown in the illustration.


d.

Install the timing gear case sub-assembly with the 7 bolts.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


e.
A326410C01
0.531,1.583 0.531,0.75 true 0.448,1.573 0.76,1.729 0.313,0.156 10 false *a
*a Period Line


Align the period lines (or matchmarks) of the injection pump assembly and timing gear case sub-assembly.


f.

Install the 2 nuts holding the injection pump assembly to the timing gear case sub-assembly.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


g.

Check that the injection pump assembly period lines (or matchmarks) are aligned.

If not correct, align the period lines (or matchmarks) by timing the injection pump assembly.


Hide 2.ADD ENGINE OIL

a.
A326421

Using a 5 mm hexagon wrench, remove the taper screw plug.


b.
A326422

Add 10 cc (0.61 cu.in.) of engine oil into the oil hole shown in the illustration.


c.

Remove any old adhesive from the taper screw plug.


d.

Apply adhesive to 3 or more threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.

Using a 5 mm hexagon wrench, install the taper screw plug.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 15104 3.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer sub-assembly with the 2 bolts and 2 nuts.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


Hide 12101 4.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old seal packing (FIPG material).


b.
A326423N01
1.938,1.198 2.094,1.396 0.156,0.198 10 false A 1.938,1.719 2.094,1.917 0.156,0.198 10 false A 2.667,1.719 2.823,1.917 0.156,0.198 10 false B 2.667,1.198 2.823,1.396 0.156,0.198 10 true B 0.75,3.042 1.188,3.229 0.438,0.188 10 false A - A 2.406,3.042 2.844,3.229 0.438,0.188 10 false B - B

Apply seal packing to the oil pan sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

5 to 13 mm (0.197 to 0.512 in.)


NOTICE:

After applying seal packing, install the oil pan sub-assembly within 5 minutes and tighten the bolts and nuts within 15 minutes.



c.

Install the oil pan sub-assembly with the 27 bolts and 3 nuts.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 13613 5.INSTALL INJECTION PUMP DRIVE GEAR

Hide 13522C 7.INSTALL PUMP DRIVE SHAFT GEAR

Hide 8.INSTALL INJECTION PUMP DRIVE GEAR OIL SEAL

Hide 11322F 10.INSTALL NO. 2 TIMING GEAR COVER

Hide 13523P 15.INSTALL CAMSHAFT TIMING PULLEY

Hide 11385 16.INSTALL CAMSHAFT OIL SEAL RETAINER