Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › ENGINE UNIT
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133486 ENGINE UNIT A

1HZ ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11381A 1.INSTALL REAR CRANKSHAFT OIL SEAL

Hide 11381 2.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the rear engine oil seal retainer or cylinder block.


b.
A326277C01
1.115,1.49 1.521,1.49 true 0.938,1.396 1.156,1.594 0.219,0.198 10 false *a 0.427,0.323 0.74,0.479 0.313,0.156 10 false *b 1.01,0.323 1.323,0.479 0.313,0.156 10 false *c
*a Seal Packing
*b CORRECT
*c INCORRECT


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4.0 to 8.0 mm (0.157 to 0.315 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the rear engine oil seal retainer within 3 minutes after applying seal packing.




c.

Install the rear engine oil seal retainer with the 6 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 11301 3.INSTALL TIMING GEAR CASE SUB-ASSEMBLY

Hide 15104 5.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12101 6.INSTALL OIL PAN SUB-ASSEMBLY

Hide 12101A 7.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 13521 8.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A329207N01
0.521,1.198 0.813,1.198 true 0.208,1.135 0.521,1.333 0.313,0.198 10 false SST

Put the timing crankshaft timing gear or sprocket with the timing mark facing frontward.


b.

Align the timing gear set key with the key groove of the crankshaft timing gear or sprocket.


c.

Using SST and a hammer, tap in the crankshaft timing gear or sprocket.

SST
09223-00010  


Hide 13613 9.INSTALL INJECTION PUMP DRIVE GEAR

a.

Install the set key to the groove of the injection pump drive shaft.


b.

Align the set key with the key groove of the injection pump drive gear and install the injection pump drive gear.


c.

Install a new O-ring to the injection pump drive gear.


Hide 13525 10.INSTALL NO. 1 IDLE GEAR

a.
A329210

Install the No. 1 idle gear shaft.


b.
A329211

Align the No. 1 idler gear timing marks "0" and "1" with the crankshaft timing gear mark "0" and injection pump drive gear timing mark "1" respectively, and mesh the gears.


c.
A329212

Align the idle gear thrust plate set bolt holes.


d.

Install the idle gear thrust plate with the 2 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 13522C 11.INSTALL DRIVE SHAFT PUMP GEAR

a.
A329213C01
0.51,0.708 0.677,0.708 0.677,0.708 0.875,0.865 false 0.208,0.635 0.5,0.802 0.292,0.167 10 false SST
V100135

Front


Align the drive shaft pump gear set key with the key groove of the drive shaft gear.


b.

Using SST and a hammer, tap in the drive shaft pump gear.

SST
09223-00010  


Hide 11322F 12.INSTALL NO. 2 TIMING GEAR COVER

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the No. 2 timing gear cover and cylinder block.

·

Using a razor blade and gasket scraper, remove all the old packing (FIPG) material from the gasket surfaces and sealing groove.

·

Thoroughly clean all components to remove all the loose material.

·

Using a non-residue solvent, clean both sealing surfaces.



b.
A329214C01
0.385,0.281 0.563,0.281 0.563,0.281 0.708,0.625 true 0.208,0.188 0.417,0.417 0.208,0.229 10 false *a 2.094,0.146 2.323,0.344 0.229,0.198 10 false *b 2.865,0.125 3.135,0.313 0.271,0.188 10 false *c
*a Seal Packing
*b CORRECT
*c INCORRECT


Apply seal packing to the No. 2 timing gear cover as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4.0 to 10.0 mm (0.157 to 0.394 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the No. 2 timing gear cover within 5 minutes after applying seal packing.




c.

Install the No. 2 timing gear cover with the 15 bolts.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 15.CHECK PISTON PROTRUSION AND SELECT CYLINDER HEAD GASKET

Hide 11101 18.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 16100 19.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 20.INSTALL VALVE LIFTER AND ADJUSTING VALVE SHIM

a.

Install the 12 valve lifters and 12 adjusting valve shims.


b.

Check the valve lifter rotates smoothly by hand.


Hide 11183 21.INSTALL SEMICIRCULAR PLUG

a.

Remove any old packing (FIPG) material.


b.
A326340

Apply seal packing to the semicircular plug as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent



c.

Install the semicircular plug to the cylinder head sub-assembly.


Hide 11385 26.INSTALL CAMSHAFT OIL SEAL RETAINER

Hide 13523P 27.INSTALL CAMSHAFT TIMING PULLEY

Hide 11201 28.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12108 29.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 15710 30.INSTALL OIL COOLER ASSEMBLY

Hide 23600 32.INSTALL NOZZLE HOLDER AND NOZZLE SET

Hide 23760 33.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 34.INSTALL ENGINE HANGER

a.
A326287C01
0.052,0.063 0.323,0.281 0.271,0.219 10 false *A 1.906,0.052 2.219,0.208 0.313,0.156 10 false *B
*A for Front Side
*B for Rear Side


Install the 2 engine hangers with the 4 bolts as shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)