The ECM controls the internal fuel pressure of the common rail by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.
For more information on the pressure discharge valve and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).
For more information on the injector driver, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).
If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1271 | Fuel Regulator Circuit Malfunction (EDU Drive) | Either condition is met (1 trip detection logic):
·
Open or short in pressure discharge valve circuit.
·
There is no valve opening confirmation (INJF) signal from the injector driver to the ECM for a specific number of times consecutively despite the ECM sending valve opening command (PRD) signals after the engine is started. |
·
Open or short in pressure discharge valve circuit
·
Pressure discharge valve (common rail assembly (for bank 2))
·
Injector driver |
Comes on | DTC stored |
| P1272 | Fuel Pressure Regulator Malfunction | Pressure discharge valve does not open. Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off (2 trip detection logic). |
·
Open or short in pressure discharge valve circuit (P1271 is stored simultaneously)
·
Pressure discharge valve (common rail assembly (for bank 2))
·
Injector driver
·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P1271 |
·
Common Rail Pressure
·
Target Common Rail Pressure
·
Pressure discharge valve |
| P1272 |
After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail by entering the following menus:
Powertrain / Engine / Data List / Common Rail Pressure.
P1271:
After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not output.
P1272:
After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.
| Engine Speed | Fuel Pressure (kPa) |
|---|---|
| Idling | Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure |
| 2500 rpm (No engine load) |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P1271 | Engine switch on (IG) to off and drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal |
| P1272 | Ignition switch ON to off |
This DTC will be stored if there is no valve opening confirmation (RLF) signal sent from the injector driver to the ECM despite the ECM commanding the injector driver to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.
The injector driver monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the injector driver interprets this as the INJF signal being low. If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
The pressure discharge valve will open and discharge the internal fuel pressure from the common rail to the fuel tank when the ignition switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then determines that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the ignition switch has been turned off.
If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After completing repairs, confirm that P1271 and/or P1272 does not recur.
If P062D (No. 1 injector driver) and P1271 are present simultaneously, there is an open in the INJF wire harness between the injector driver and ECM, or there is an open in the wire harness for both an fuel injector and the pressure discharge valve.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| P1272 | A |
| P1271 | B |
| P1271 and P1272 | B |
| Other DTCs output | C |
A
B
C
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain /Engine / Utility / Pressure Discharge Valve Check.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST
| Tester Display |
|---|
| Pressure Discharge Valve Check |
Select "Close to Open Check".
Read the value of "Open and Engine OFF".
0.5 MPa or less
When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.
When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.
When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.
Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the common rail assembly (for Bank 2).
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION
Perform PM forced regeneration.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P1271 and P1272.
Check the DTC judgment result.
If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the common rail assembly (for Bank 2).
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector driver connector.
Disconnect the pressure discharge valve connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| v1-2 (COM3) - C121-2 (RLF+) | Always | Below 1 Ω |
| v1-1 (RLV) - C121-1 (RLF-) | Always | Below 1 Ω |
| v1-2 (COM3) or C121-2 (RLF+) - Body ground | Always | 10 kΩ or higher |
| v1-1 (RLV) or C121-1 (RLF-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C122-4 (PRD) - C39-54 (PRD) | Always | Below 1 Ω |
| C122-8 (INJF) - C39-32 (RLFF) | Always | Below 1 Ω |
| C122-4 (PRD) or C39-54 (PRD) - Body ground | Always | 10 kΩ or higher |
| C122-8 (INJF) or C39-32 (RLFF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Injector Driver) |
Disconnect the injector driver connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C124-3 (+B) - C124-1 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector driver.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P1271 and P1272.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P1271 and/or P1272 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.
A
B
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Go to injector circuit.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>Injector Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT