Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2016.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  Black Smoke Emitted  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing a fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Result Proceed to
No DTC is output A
DTCs related to engine B




A

2.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)

B

REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT

2.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Volume
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 376,368,369,370,371,372,373,374,375

d.

Enter the following menus in order and read the values.

·

Injection Volume

·

Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8


Standard value:
Item Engine Speed* Reference Value
Injection Volume Idling (No engine load) 3.0 to 10.0 mm3
Injection Feedback Val #1 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #2 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #3 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #4 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #5 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #6 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #7 Idling (No engine load) -3.0 to 3.0 mm3
Injection Feedback Val #8 Idling (No engine load) -3.0 to 3.0 mm3


HINT:

*: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE RPM ACCELERATION

NG

11.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
3.PERFORM ENGINE RPM ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations.


a.

Accelerate the engine speed to the maximum rpm with no load 20 times.


b.

Check the volume of black smoke in the exhaust gas.

Result:
Result Proceed to
Black smoke is not present OK
Black smoke remains in the exhaust gas NG


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.




OK

END

NG

4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
a.

Result:
Proceed to
OK
NG



OK

5.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

5.INSPECT MASS AIR FLOW METER

Result:
Proceed to
OK
NG



OK

6.CHECK TURBOCHARGER PRESSURE

NG

6.CHECK TURBOCHARGER PRESSURE
a.

Check the turbocharger pressure.

Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER (w/o DPF)>INSPECTION

OK:

The turbocharger pressure is within the standard range.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (DATA LIST)

NG

7.READ VALUE USING GTS (DATA LIST)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Volume
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
Pilot 2 Injection Period
Main Injection Period
Fuel Press
50003 61 376,368,369,370,371,372,373,374,375,360,361,54

d.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume

·

Main Injection

·

Pilot 2 Injection

·

Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8


Standard value:
Item Engine Speed* Reference Value
Fuel Press Idling 27000 to 37000 kPa
Fuel Press 2000 rpm (no engine load) 50000 to 70000 kPa
Fuel Press 3000 rpm (no engine load) 52000 to 76000 kPa
Injection Volume Idling 3.0 to 10.0 mm3
Injection Volume 2000 rpm (no engine load) 5.5 to 12.5 mm3
Injection Volume 3000 rpm (no engine load) 5.5 to 12.5 mm3
Main Injection Idling 490 to 690 μs
Pilot 2 Injection Idling 390 to 490 μs
Injection Feedback Val #1 Idling -3.0 to 3.0 mm3
Injection Feedback Val #2 Idling -3.0 to 3.0 mm3
Injection Feedback Val #3 Idling -3.0 to 3.0 mm3
Injection Feedback Val #4 Idling -3.0 to 3.0 mm3
Injection Feedback Val #5 Idling -3.0 to 3.0 mm3
Injection Feedback Val #6 Idling -3.0 to 3.0 mm3
Injection Feedback Val #7 Idling -3.0 to 3.0 mm3
Injection Feedback Val #8 Idling -3.0 to 3.0 mm3


HINT:

*: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.


Result:
Result Proceed to
Within reference value A
One of Injection Feedback Val #1 to #8 is not within reference value B
Other result C




A

8.CHECK CYLINDER COMPRESSION PRESSURE

B

GO TO DTC P1238 INSPECTION PROCEDURE

C

11.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
8.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.HARNESS AND CONNECTOR (INJECTOR - EDU)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

9.HARNESS AND CONNECTOR (INJECTOR - EDU)
a.
A311469C04
0.698,0.469 1.083,0.75 0.385,0.281 1.198,0.469 1.583,0.75 0.385,0.281 1.698,0.469 2.083,0.75 0.385,0.281 2.167,0.469 2.552,0.75 0.385,0.281 1.5,2.635 1.885,2.917 0.385,0.281 0.469,4.167 0.99,3.625 true 0.854,4.156 1.198,3.635 true 1.198,4.167 1.385,3.646 true 1.583,4.146 1.583,3.656 true 2.031,4.156 1.781,3.656 true 2.51,4.167 1.99,3.667 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 0.219,2.271 0.531,2.427 0.313,0.156 10 false *b 0.781,0.531 1.094,0.688 0.313,0.156 10 false C48 1.271,0.531 1.583,0.688 0.313,0.156 10 false C72 1.771,0.531 2.083,0.688 0.313,0.156 10 false C64 2.25,0.531 2.563,0.688 0.313,0.156 10 false C57 1.583,2.698 1.896,2.854 0.313,0.156 10 false C55 0.323,4.188 0.698,4.344 0.375,0.156 10 false INJ7 0.729,4.188 1.104,4.344 0.375,0.156 10 false INJ6 1.083,4.188 1.458,4.344 0.375,0.156 10 false INJ4 1.458,4.188 1.833,4.344 0.375,0.156 10 false INJ1 1.844,4.188 2.281,4.344 0.438,0.156 10 false COM1 2.365,4.188 2.813,4.365 0.448,0.177 10 false COM2
*a Front view of wire harness connector
(to Fuel Injector)
*b Front view of wire harness connector
(to No. 1 EDU)


Disconnect the C48, C72, C64 and C57 fuel injector connectors.


b.

Disconnect the C55 No. 1 EDU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (No. 1):
Tester Connection Condition Specified Condition
C48-2 - C55-4 (INJ1) Always Below 1 Ω
C72-2 - C55-3 (INJ4) Always Below 1 Ω
C64-2 - C55-2 (INJ6) Always Below 1 Ω
C57-2 - C55-1 (INJ7) Always Below 1 Ω
C48-1 - C55-5 (COM1) Always Below 1 Ω
C72-1 - C55-5 (COM1) Always Below 1 Ω
C64-1 - C55-6 (COM2) Always Below 1 Ω
C57-1 - C55-6 (COM2) Always Below 1 Ω
C48-2 or C55-4 (INJ1) - Body ground Always 10 kΩ or higher
C72-2 or C55-3 (INJ4) - Body ground Always 10 kΩ or higher
C64-2 or C55-2 (INJ6) - Body ground Always 10 kΩ or higher
C57-2 or C55-1 (INJ7) - Body ground Always 10 kΩ or higher
C48-1 or C55-5 (COM1) - Body ground Always 10 kΩ or higher
C72-1 or C55-5 (COM1) - Body ground Always 10 kΩ or higher
C64-1 or C55-6 (COM2) - Body ground Always 10 kΩ or higher
C57-1 or C55-6 (COM2) - Body ground Always 10 kΩ or higher



d.
A311469C05
0.667,0.333 1.083,0.594 0.417,0.26 1.188,0.333 1.604,0.594 0.417,0.26 1.708,0.333 2.125,0.594 0.417,0.26 2.25,0.333 2.667,0.594 0.417,0.26 1.448,2.656 1.865,2.917 0.417,0.26 1.833,4.167 1.583,3.646 true 2.75,4.083 2,3.667 true 2.271,4.156 1.781,3.646 true 1.333,4.167 1.417,3.646 true 0.896,4.167 1.219,3.646 true 0.417,4 1.052,3.646 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.208,2.688 0.521,2.885 0.313,0.198 10 false *b 1.563,2.708 2.021,2.906 0.458,0.198 10 false C53 0.76,0.385 1.052,0.563 0.292,0.177 10 false C67 1.292,0.385 1.583,0.552 0.292,0.167 10 false C51 1.792,0.385 2.094,0.563 0.302,0.177 10 false C49 2.333,0.385 2.635,0.573 0.302,0.188 10 false C63 0.302,4 0.917,4.198 0.615,0.198 10 false INJ3 0.75,4.219 1.365,4.417 0.615,0.198 10 false INJ8 1.229,4.229 1.844,4.427 0.615,0.198 10 false INJ5 1.75,4.24 2.365,4.438 0.615,0.198 10 false INJ2 2.167,4.24 2.781,4.438 0.615,0.198 10 false COM4 2.667,4.083 3.281,4.281 0.615,0.198 10 false COM5
*a Front view of wire harness connector
(to Fuel Injector)
*b Front view of wire harness connector
(to No. 2 EDU)


Disconnect the C67, C51, C49 and C63 fuel injector connectors.


e.

Disconnect the C53 No. 2 EDU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard resistance (No. 2):
Tester Connection Condition Specified Condition
C67-2 - C53-4 (INJ2) Always Below 1 Ω
C51-2 - 53-3 (INJ5) Always Below 1 Ω
C49-2 - C53-1 (INJ3) Always Below 1 Ω
C63-2 - C53-2 (INJ8) Always Below 1 Ω
C67-1 - C53-5 (COM4) Always Below 1 Ω
C51-1 - C53-5 (COM4) Always Below 1 Ω
C49-1 - C53-6 (COM5) Always Below 1 Ω
C63-1 - C53-6 (COM5) Always Below 1 Ω
C67-2 or C53-4 (INJ2) - Body ground Always 10 kΩ or higher
C51-2 or C53-3 (INJ5) - Body ground Always 10 kΩ or higher
C49-2 or C53-1 (INJ3) - Body ground Always 10 kΩ or higher
C63-2 or C53-2 (INJ8) - Body ground Always 10 kΩ or higher
C67-1 or C53-5 (COM4) - Body ground Always 10 kΩ or higher
C51-1 or C53-5 (COM4) - Body ground Always 10 kΩ or higher
C49-1 or C53-6 (COM5) - Body ground Always 10 kΩ or higher
C63-1 or C53-6 (COM5) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.PERFORM GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the engine idle speed while the fuel injection to each cylinder is cut using the GTS.

Result:
Result Proceed to
Becomes unstable A
Does not change B


HINT:

Replace the injector mounted on the cylinder that causes no significant idle speed change.




A

B

GO TO DTC P1238 INSPECTION PROCEDURE

11.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Coolant Temp Idling with warm engine (A/C switch OFF) 75 to 90°C (167 to 194°F)



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (MAP)

NG

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
12.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 61 314

e.

Read the value.

OK:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (ENGINE SPEED)

NG

17.HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
13.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 61 315

e.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Engine Speed Idling with warm engine (A/C switch OFF) 500 to 600 rpm



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (ACCEL SENSOR OUT NO. 1 AND 2)

NG

23.INSPECT CRANKSHAFT POSITION SENSOR
14.READ VALUE USING GTS (ACCEL SENSOR OUT NO. 1 AND 2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 61 412,413

d.

Read the value.

Standard voltage:
Item Accelerator Pedal Condition Reference Value
Accel Sensor Out No. 1 Released 0.6 to 1.0 V
Accel Sensor Out No. 1 Depressed 3.4 to 3.8 V
Accel Sensor Out No. 2 Released 1.4 to 1.8 V
Accel Sensor Out No. 2 Depressed 4.2 to 4.6 V



Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (INTAKE AIR)

NG

18.HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
15.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

OK:

Same as air temperature near intake manifold.



Result:
Proceed to
OK
NG



OK

16.READ VALUE USING GTS (FUEL PRESS)

NG

24.INSPECT INTAKE AIR TEMPERATURE SENSOR (MASS AIR FLOW METER)
16.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Press
50003 61 54

e.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Fuel Press Idling 27000 to 37000 kPa



Result:
Proceed to
OK
NG



OK

NG

19.INSPECT FUEL PRESSURE SENSOR
17.HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.
A311456C11
1.458,0.146 1.854,0.375 0.396,0.229 1.323,2.313 1.719,2.542 0.396,0.229 1.177,1.604 1.458,1.094 true 2.135,1.615 1.875,1.104 true 1.667,1.615 1.667,1.104 true 0.531,4.177 0.646,3.396 true 1.365,4.188 0.823,3.563 true 2.063,4.167 1.427,3.396 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.125,2.021 0.438,2.219 0.313,0.198 10 false *b 1.5,0.177 1.906,0.396 0.406,0.219 10 false C101 1.083,1.635 1.396,1.833 0.313,0.198 10 false E 1.583,1.646 1.896,1.844 0.313,0.198 10 false PIM 2.083,1.646 2.396,1.844 0.313,0.198 10 false VC 1.396,2.344 1.708,2.542 0.313,0.198 10 false C39 0.313,4.208 1.021,4.479 0.708,0.271 10 false 66 (VCPM) 1.25,4.208 1.906,4.542 0.656,0.333 10 false 114 (PIM) 2.01,4.208 2.594,4.427 0.583,0.219 10 false 75 (E2)
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C101 manifold absolute pressure sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C101-2 (PIM) - C39-114 (PIM) Always Below 1 Ω
C101-3 (VC) - C39-66 (VCPM) Always Below 1 Ω
C101-1 (E) - C39-75 (E2) Always Below 1 Ω
C101-2 (PIM) or C39-114 (PIM) - Body ground Always 10 kΩ or higher
C101-3 (VC) or C39-66 (VCPM) - Body ground Always 10 kΩ or higher
C101-1 (E) or C39-75 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.
A311474C03
1.563,2.479 2.01,2.75 0.448,0.271 1.49,0.219 1.938,0.49 0.448,0.271 0.688,1.281 1.354,1.125 true 1.365,1.688 1.667,1.146 true 0.896,1.51 1.542,1.146 true 1.844,1.688 1.792,1.135 true 1.917,1.156 2.219,1.531 true 2.063,1.135 2.563,1.406 true 1.823,3.781 0.646,3.615 true 1.917,3.781 0.802,4.125 true 2.01,3.781 1.125,4.302 true 2.083,3.781 1.583,4.375 true 2.26,3.781 2.625,4.094 true 2.188,3.781 2.125,4.208 true 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 0.177,2.448 0.49,2.646 0.313,0.198 10 false *b 1.656,2.552 1.979,2.74 0.323,0.188 10 false A29 1.615,0.281 1.865,0.448 0.25,0.167 10 false I43 0.271,1.219 0.885,1.417 0.615,0.198 10 false VCP2 0.615,1.521 1.229,1.719 0.615,0.198 10 false EPA2 1.208,1.719 1.823,1.917 0.615,0.198 10 false VPA2 1.781,1.729 2.396,1.927 0.615,0.198 10 false VCPA 2.24,1.563 2.854,1.76 0.615,0.198 10 false EPA 2.625,1.406 3.24,1.604 0.615,0.198 10 false VPA 0.104,4.073 1.031,4.344 0.927,0.271 10 false 54 (VPA2) 0.063,3.51 0.74,3.802 0.677,0.292 10 false 53 (VPA) 0.698,4.323 1.792,4.583 1.094,0.26 10 false 55 (VCPA) 1.448,4.406 2.823,4.604 1.375,0.198 10 false 56 (VCP2) 1.938,4.24 3.313,4.438 1.375,0.198 10 false 57 (EPA) 2.5,4.115 3.323,4.344 0.823,0.229 10 false 58 (EPA2)
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the I43 accelerator pedal position sensor connector.


b.

Disconnect the A29 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
I43-1 (VCP2) - A29-56 (VCP2) Always Below 1 Ω
I43-2 (EPA2) - A29-58 (EPA2) Always Below 1 Ω
I43-3 (VPA2) - A29-54 (VPA2) Always Below 1 Ω
I43-4 (VCPA) - A29-55 (VCPA) Always Below 1 Ω
I43-5 (EPA) - A29-57 (EPA) Always Below 1 Ω
I43-6 (VPA) - A29-53 (VPA) Always Below 1 Ω
I43-1 (VCP2) or A29-56 (VCP2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or A29-58 (EPA2) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or A29-54 (VPA2) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or A29-55 (VCPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or A29-57 (EPA) - Body ground Always 10 kΩ or higher
I43-6 (VPA) or A29-53 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT FUEL PRESSURE SENSOR
a.
A165963C01
1.458,2.375 1.125,2.833 true 1.729,2.385 1.74,2.833 true 2.083,2.365 2.375,2.823 true 0.24,0.469 1.198,0.938 0.958,0.469 10 false *a 0.99,2.844 1.229,3.021 0.24,0.177 10 false VC 1.635,2.844 1.875,3.021 0.24,0.177 10 false PR 2.292,2.844 2.531,3.021 0.24,0.177 10 false E2
*a Component without harness connected
(Fuel Pressure Sensor)


Disconnect the C56 fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
2 (PR) - 1 (E2) Always 16.4 kΩ or less
2 (PR) - 3 (VC) Always 3 kΩ or less



Result:
Proceed to
OK
NG



OK

20.HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

20.HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.
A311456C06
1.458,0.146 1.854,0.375 0.396,0.229 1.323,2.313 1.719,2.542 0.396,0.229 1.177,1.604 1.458,1.094 true 2.135,1.615 1.875,1.104 true 1.667,1.615 1.667,1.104 true 0.531,4.177 0.906,3.396 true 1.365,4.188 0.99,3.396 true 2.063,4.167 1.427,3.396 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.125,2.021 0.438,2.219 0.313,0.198 10 false *b 1.542,0.177 1.854,0.375 0.313,0.198 10 false C56 1.094,1.646 1.406,1.844 0.313,0.198 10 false E2 1.583,1.646 1.896,1.844 0.313,0.198 10 false PR 2.083,1.646 2.396,1.844 0.313,0.198 10 false VC 1.396,2.344 1.708,2.542 0.313,0.198 10 false C39 0.396,4.208 1.104,4.479 0.708,0.271 10 false 69 (PCR1) 1.25,4.208 1.906,4.542 0.656,0.333 10 false 70 (VCM) 2.01,4.208 2.594,4.427 0.583,0.219 10 false 75 (E2)
*a Front view of wire harness connector
(to Fuel Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C56 fuel pressure sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C56-2 (PR) - C39-69 (PCR1) Always Below 1 Ω
C56-3 (VC) - C39-70 (VCM) Always Below 1 Ω
C56-1 (E2) - C39-75 (E2) Always Below 1 Ω
C56-2 (PR) or C39-69 (PCR1) - Body ground Always 10 kΩ or higher
C56-3 (VC) or C39-70 (VCM) - Body ground Always 10 kΩ or higher
C56-1 (E2) or C39-75 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.REPLACE ECM
a.

Replace the ECM.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check if the engine starts smoothly or if the engine stalls.

OK:

The engine starts smoothly and does not stall.



Result:
Proceed to
OK
NG



OK

END

NG

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Remove the engine coolant temperature sensor.

A163511C03
5.583,1.781 5.875,1.417 false 2.104,1.25 2.49,0.875 true 1.781,1.24 1.406,0.854 true 3.406,0.635 4.615,0.917 1.208,0.281 10 false Resistance kΩ 6.01,1.219 7.021,1.448 1.01,0.229 10 false Acceptable 4.646,0.708 4.969,0.917 0.323,0.208 8 false 30 4.646,0.833 4.969,1.042 0.323,0.208 8 false 20 4.646,1.042 4.969,1.25 0.323,0.208 8 false 10 4.646,1.302 4.969,1.51 0.323,0.208 8 false 5 4.646,1.458 4.969,1.667 0.323,0.208 8 false 3 4.646,1.625 4.969,1.833 0.323,0.208 8 false 2 4.646,1.823 4.969,2.031 0.323,0.208 8 false 1 4.646,2.354 4.969,2.563 0.323,0.208 8 false 0.2 4.646,2.229 4.969,2.438 0.323,0.208 8 false 0.3 4.646,2.073 4.969,2.281 0.323,0.208 8 false 0.5 4.646,2.583 4.969,2.792 0.323,0.208 8 false 0.1 5.115,2.917 5.344,3.302 0.229,0.385 8 false 0 (32) 5.365,2.917 5.677,3.24 0.313,0.323 8 false 20 (68) 5.604,2.917 5.938,3.24 0.333,0.323 8 false 40 (104) 5.875,2.917 6.219,3.24 0.344,0.323 8 false 60 (140) 6.135,2.917 6.563,3.24 0.427,0.323 8 false 80 (176) 6.427,2.917 6.792,3.24 0.365,0.323 8 false 100 (212) 4.865,2.917 5.104,3.25 0.24,0.333 8 false -20 (-4) 3.25,2.854 4.729,3.083 1.479,0.229 10 false Temperature °C (°F) 0.51,0.271 1.281,0.656 0.771,0.385 10 false *a 2.542,0.75 2.792,0.938 0.25,0.188 10 false E2 1.042,0.76 1.396,0.948 0.354,0.188 10 false THW
*a Component without harness connected
(Engine Coolant Temperature Sensor)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 (E2) - 2 (THW) 20°C (68°F) 2.29 to 2.60 kΩ
1 (E2) - 2 (THW) 80°C (176°F) 0.301 to 0.327 kΩ


NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



c.

Reconnect the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

23.INSPECT CRANKSHAFT POSITION SENSOR
a.
A165740C02
1.458,2.104 1.156,1.74 true 1.979,2.135 2.292,1.74 true 0.188,0.448 0.729,0.896 0.542,0.448 10 false *a 2.375,1.615 2.729,1.802 0.354,0.188 10 false NE+ 0.76,1.615 1.031,1.802 0.271,0.188 10 false NE-
*a Component without harness connected
(Crankshaft Position Sensor)


Disconnect the C42 crankshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 (NE+) - 2 (NE-) Cold 1630 to 2740 Ω
1 (NE+) - 2 (NE-) Hot 2065 to 3225 Ω


HINT:

In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" mean sapproximately 50 to 100°C (122 to 212°F).



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

24.INSPECT INTAKE AIR TEMPERATURE SENSOR (MASS AIR FLOW METER)
a.

Remove the mass air flow meter.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/o DPF)>REMOVAL

A168114C01
2.24,2.813 2.448,3.25 false 1.844,3.271 2.115,2.813 false 6.052,1.542 5.354,1.813 false 1.5,3.292 1.958,3.479 0.458,0.188 10 false 5 (E2) 2.333,3.281 2.875,3.458 0.542,0.177 10 false 4 (THA) 4.167,0.479 4.396,0.656 0.229,0.177 10 false 30 4.167,0.656 4.375,0.833 0.208,0.177 10 false 20 4.167,0.927 4.385,1.115 0.219,0.188 10 false 10 4.229,1.208 4.375,1.385 0.146,0.177 10 false 5 4.229,1.427 4.354,1.594 0.125,0.167 10 false 3 4.229,1.604 4.365,1.76 0.135,0.156 10 false 2 4.229,1.875 4.375,2.042 0.146,0.167 10 false 1 4.167,2.156 4.406,2.323 0.24,0.167 10 false 0.5 4.167,2.354 4.417,2.521 0.25,0.167 10 false 0.3 4.167,2.51 4.448,2.677 0.281,0.167 10 false 0.2 4.167,2.76 4.406,2.927 0.24,0.167 10 false 0.1 4.448,3.177 4.76,3.365 0.313,0.188 10 false -20 4.844,3.177 4.969,3.323 0.125,0.146 10 false 0 5.104,3.177 5.313,3.344 0.208,0.167 10 false 20 5.396,3.177 5.604,3.344 0.208,0.167 10 false 40 5.698,3.177 5.927,3.344 0.229,0.167 10 false 60 6,3.177 6.198,3.333 0.198,0.156 10 false 80 6.281,3.177 6.563,3.354 0.281,0.177 10 false 100 4.427,3.365 4.688,3.542 0.26,0.177 10 false (-4) 4.729,3.365 5.021,3.542 0.292,0.177 10 false (32) 5.031,3.365 5.323,3.542 0.292,0.177 10 false (68) 5.313,3.365 5.698,3.542 0.385,0.177 10 false (104) 5.646,3.365 6.031,3.542 0.385,0.177 10 false (140) 5.979,3.365 6.365,3.542 0.385,0.177 10 false (176) 6.344,3.365 6.729,3.542 0.385,0.177 10 false (212) 6.073,1.458 6.844,1.625 0.771,0.167 10 false Acceptable 2.979,1.083 3.979,1.271 1,0.188 10 false Resistance kΩ 3.052,3.219 4.344,3.406 1.292,0.188 10 false Temperature °C (°F) 0.563,0.292 1.115,0.688 0.552,0.396 10 false *a
*a Component without harness connected
(Mass Air Flow Meter)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) -20°C (-4°F) 13.6 to 18.4 kΩ
20°C (68°F) 2.21 to 2.69 kΩ
60°C (140°F) 0.49 to 0.67 kΩ



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG