| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|---|---|---|
|
·
Lack of power caused by abnormal fuel injection volume (fuel supply pump assembly malfunction, fuel injector malfunction, etc.)
·
Lack of power caused by intake air volume shortage (turbocharger malfunction or exhaust manifold converter sub-assembly blocked) |
(a) Fuel injector malfunctions
·
Injector sliding malfunction
·
Injector stuck closed
·
Injector stuck open
·
Deposits in injector
·
Injector circuit malfunction (b) Abnormal Fuel pressure
·
Suction control valve (c) Abnormal intake air volume
·
Intake system leakage or clogged
·
Turbocharger sub-assembly
·
Front exhaust pipe blockage
·
Throttle valve does not open |
·
Intake air system blockage
·
Fuel filter element assembly is clogged
·
Throttle valve
·
Mass air flow meter
·
Compression pressure
·
Injector compensation code
·
Fuel leak
·
Glow plug
·
Fuel pressure sensor
·
Manifold absolute pressure sensor
·
Vacuum hose connection for manifold absolute pressure sensor
·
Vehicle modifications
·
Clutch disc wear
·
Low quality fuel
·
Frozen fuel
·
ECM |
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
Check that the vehicle has not been modified in any way prior to the vehicle inspection.
This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).
Faults and Symptoms of Common Rail Diesel Components
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) |
| Symptoms | Lack of power, black smoke |
| Data List | MAF |
|
|
| Symptom and Corresponding Main Fault |
·
Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct
·
Black smoke (no lack of power) due to leakage between the turbo and intake manifold |
| Data List |
·
MAP
·
Target Booster Pressure When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.
·
MAF |
| Main fault |
·
Air leak in the turbocharged air passage
·
Turbocharger sub-assembly (turbine, bearing, variable nozzle) |
| Symptoms | Lack of power (when vehicle is starting, under heavy load) (Black smoke is not emitted when racing while vehicle is stopped) |
| Data List | MAP, Target Booster Pressure
·
When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.
·
With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
·
Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions. |
| Main fault | Blockage |
| Symptoms | Lack of power (high engine speed, under heavy load) |
| Data List | MAP, Target Booster Pressure When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt. |
| Main fault | Glow system malfunction |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Diagnostic Point |
·
Measure the resistance of the glow plug
·
Check the glow plug indicator light |
| Main fault | Damaged, seized up |
| Symptoms | Cannot crank, crank speed is low, strange noise |
| Main fault | Loss of compression |
| Symptoms | Rough idle (lack of power always) |
| Data List | Engine Speed of Cyl#
·
When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Val
·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. |
Diesel Injection
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel press, Target Common Rail Pressure, Target Pump SCV Current
·
Fuel press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).
·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel press is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel press, Target Common Rail Pressure
·
Fuel press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).
·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel press is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Val
·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute. |
| Main fault | Circuit fault: The fuel injector does not open. |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Same as fuel injector |
| Diagnostic Trouble Code | When the injector driver has a fault, some DTCs may be stored. |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Fuel press, Target Common Rail Pressure
·
Fuel press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms |
·
Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
·
Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur. |
| Data List | Actual Throttle Position, Actual Throttle Position #2
·
100%: Fully closed
·
0%: Fully open
·
When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily. |
Data List Related to Lack of Power
Engine Speed
MAP
MAF
Intake Air
Coolant Temp
Target Common Rail Pressure
Fuel Press
Target Pump SCV Current
Injection Feedback Val #1 (to #8)
Injection Volume
Actual Throttle Position
Actual Throttle Position #2
Explanation of Symptom
| Lack of Power | The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air. The quantity of injected fuel is determined by the fuel pressure and the amount of time the fuel injector is open. Basically, the fuel pressure is controlled so that it reaches the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as the atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than the atmospheric pressure. The manifold absolute pressure is controlled so that it reaches the Target Booster Pressure when accelerating the vehicle at full throttle. Also, when accelerating the vehicle at full throttle, the throttle is fully open, preserving the mass air flow. |
After replacing an fuel injector, the ECM needs registration (Click here ).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION
After replacing an fuel injector, the ECM needs registration.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Engine related DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Lack of Power.
With no load after the engine is warmed up, take a snapshot when idling and at 3000 rpm.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
| Proceed to |
|---|
| NEXT |
NEXT
Check MAP and MAF in the snapshot taken in procedure 2 when the engine was running at 3000 rpm with no load.
| Result | Proceed to |
|---|---|
| MAF 68 gm/sec or more and MAP 110 kPa or higher*1 | A |
| MAP is below 90 kPa*2 | B |
| Except above | C |
The above values were measured under the standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
The standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, the pressure drops by 1 kPa. This varies by weather.
*1: There may be a problem in the fuel injection system or intake system.
*2: There may be a problem in the turbocharger system.
A
B
C
Check MAP, Fuel Press and Target Common Rail Pressure in the snapshot taken in procedure 3 when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
| Result | Proceed to |
|---|---|
| MAP is below 150 kPa at an engine speed of 3000 rpm | A |
| Difference between Fuel Press and Target Common Rail Pressure is 20000 kPa or more | B |
| Except above | C |
The above values were measured under the standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. The standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, the pressure drops by 1 kPa. This varies by weather.
The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.
If the turbocharger movement is not smooth, etc., the value of MAP in the snapshot taken during lack of power will not reach the target value. When the accelerator pedal is fully depressed and the engine speed is 3000 rpm, the MAP should be higher than 170 kPa.
A
B
C
Check for air leaks and blockages between the air cleaner case and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
Inspect the intake system, especially hoses and pipes between the air cleaner filter element sub-assembly and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
Check for any modifications in the intake system made by the user.
No leakage or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clean the fuel filter case and replace the fuel filter element assembly.
Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assemblies.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL
When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION
| Tester Display |
|---|
| Injector Compensation |
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
| Tester Display |
|---|
| Atmosphere Pressure |
| MAP |
Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).
Difference between MAP and Atmosphere Pressure is less than 8 kPa.
If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
The standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, the pressure drops by 1 kPa. This varies by weather.
| Result | Proceed to |
|---|---|
| MAP and Atmosphere Pressure have same value | A |
| MAP is different from actual atmospheric pressure | B |
| Atmosphere Pressure is different from actual atmospheric pressure | C |
A
B
C
Check for air leaks and blockages between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
| Result | Proceed to |
|---|---|
| Leaks and/or blockages exist in the intake system | A |
| No leaks or blockages in the intake system | B |
Inspect the intake system, especially hoses and pipes between the air cleaner filter element sub-assembly and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
When inspecting for a clogged intake system (cause of low MAP), check the following points:
- Clogged air cleaner
- Clogged intake hose
- Diesel throttle valve stuck in closed position
Check for any modifications in the intake system made by the user.
A
B
Repair or replace the malfunctioning part in the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the turbocharger sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for intermittent problems.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Fuel Press.
| Tester Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
With no load after the engine is warmed up, take a snapshot when idling and the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Check the Target Common Rail Pressure and Common Rail Pressure value.
| Result | Proceed to |
|---|---|
| While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 | A |
| "Fuel Press" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2 | |
| Except above | B |
*1: The cause may be a squashed or blocked fuel pipe or hose.
*2: The cause may be a clogged fuel filter.
A
B
Repair or replace the clogged (including frozen fuel) fuel pipe.
Replace the fuel filter element assembly.
If "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press and Target Common Rail Pressure.
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
"Fuel Press" is the actual fuel pressure.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the turbocharger sub-assembly.
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER (w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for air leaks and blockages between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
| Result | Proceed to |
|---|---|
| No leaks or blockages in the intake system | A |
| Leaks and/or blockages exist in the intake system | B |
Inspect the intake system, especially hoses and pipes between the air cleaner filter element sub-assembly and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.
Check for any modifications in the intake system made by the user.
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Engine speed.
| Tester Display |
|---|
| Engine Speed |
| MAF |
Start the engine and read the value when 30 seconds has elapsed.
| Engine speed | MAF |
|---|---|
| Idling | 6.1 to 26.5 gm/sec |
| 3000 rpm | 68 to 170 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front exhaust pipe assembly.
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (except 5 Door)>REMOVAL
Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.
Less than 10% of the cells are clogged.
Reinstall the front exhaust pipe assembly.
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (except 5 Door)>INSTALLATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the turbocharger sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for intermittent problems.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the malfunctioning part in the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the mass air flow meter.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/o DPF)>REMOVAL
If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the turbocharger sub-assembly.
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER (w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the front exhaust pipe assembly.
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (except 5 Door)>REMOVAL
Perform initialization procedure for Catalyst Record Clear.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT