When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
53301 3.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer hose.
Remove the 4 bolts and hood sub-assembly.
16400 4.REMOVE RADIATOR ASSEMBLY
17940D 5.REMOVE INTERCOOLER ASSEMBLY
6.DRAIN ENGINE OIL
7.DRAIN MANUAL TRANSMISSION OIL
87246A 8.DISCONNECT HEATER WATER HOSE
| *1 | Inlet Heater Water Hose |
| *2 | Outlet Heater Water Hose |
Slide the clamp and disconnect the inlet heater water hose from the outlet heater water pipe B.
Slide the clamp and disconnect the outlet heater water hose from the outlet heater water pipe B.
87250 9.REMOVE HEATER WATER VALVE ASSEMBLY
28800 10.REMOVE BATTERY
Remove the bolt, nut, battery clamp and battery.
74403A 11.REMOVE BATTERY CARRIER SUB-ASSEMBLY
Remove the bolt.
Detach the clamp and disconnect the No. 2 fuse block from the battery carrier sub-assembly.
Remove the fusible link block cover.
Remove the bolt and disconnect the engine wire.
Detach the wire harness clamp.
Remove the 2 bolts.
Detach the clamp and disconnect the fusible link block from the battery carrier sub-assembly.
Detach the 3 wire harness clamps.
Remove the 5 bolts and battery carrier sub-assembly.
44310 12.DISCONNECT VANE PUMP ASSEMBLY
Disconnect the power steering oil pressure switch connector.
Remove the 2 nuts and disconnect the vane pump assembly.
It is not necessary to completely remove the vane pump assembly. With the hoses connected to the vane pump assembly, hang the vane pump assembly on the vehicle body with a rope.
Remove the O-ring from the vane pump assembly.
88320 13.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the cooler compressor assembly connector.
Remove the 4 bolts and disconnect the cooler compressor assembly.
It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.
44778 14.DISCONNECT CONNECTOR TO CHECK VALVE HOSE
| *A | w/o DPF |
| *B | w/ DPF |
Slide the clamp and disconnect the connector from the check valve hose of the cylinder head cover sub-assembly.
23271H 15.DISCONNECT NO. 1 AND NO. 2 FUEL HOSES
| *A | w/o DPF |
| *B | w/ DPF |
| *1 | No. 1 Fuel Hose |
| *2 | No. 2 Fuel Hose |
Slide the clamp and disconnect the No. 1 fuel hose from the fuel filter cap assembly.
Slide the clamp and disconnect the No. 2 fuel hose from the fuel pipe.
82111 16.DISCONNECT ENGINE ROOM MAIN WIRE
Disconnect the ECM connector.
| *A | w/o DPF | *B | for LHD |
| *C | for RHD | - | - |
for LHD:
Detach the engine room main wire clamp.
Detach the 2 engine room main wire clamps.
w/o DPF:
Disconnect the 4 connectors and detach the clamp.
w/ DPF:
Disconnect the 7 connectors and detach the clamp.
| *a | Push |
| *b | Lock |
Raise the levers while pushing the locks on the levers and disconnect the connectors.
17362B 17.REMOVE NO. 2 AIR TUBE
17343D 18.REMOVE NO. 3 AIR HOSE
17971 19.REMOVE NO. 1 COOL AIR INLET
17972 20.REMOVE NO. 2 COOL AIR INLET
82111 21.DISCONNECT ENGINE ROOM MAIN WIRE
w/ DPF:
Disconnect the 6 connectors.
Disconnect the 4 fuel injector connectors.
Remove the 5 bolts.
Detach the 2 clamps and disconnect the engine wire.
Disconnect the 6 connectors.
Disconnect the 4 fuel injector connectors.
Remove the 3 bolts.
Detach the 2 clamps and disconnect the engine wire.
Remove the 2 bolts and disconnect the 2 ground wires.
Detach the 2 clamps and disconnect the 2 connectors.
Detach the 2 clamps and disconnect the engine wire.
Remove the 2 bolts and disconnect the 2 wire harness clamps and 2 connectors.
w/o DPF:
Disconnect the engine wire connected to the engine assembly.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>CAMSHAFT (w/o DPF)>REMOVAL
26100G 22.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)
26100G 23.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)
23265 24.REMOVE NO. 1 GAS FILTER
17947B 25.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET
16264 26.DISCONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES (w/o DPF)
23284A 27.REMOVE NO. 5 FUEL HOSE (w/o DPF)
23804D 28.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/o DPF)
44769 29.REMOVE VACUUM RESERVOIR CONNECT TUBE
82112 30.DISCONNECT NO. 2 ENGINE ROOM WIRE
44761 31.REMOVE VACUUM PUMP TO CONNECTOR TUBE
23243C 32.DISCONNECT FUEL PUMP MOTOR WIRE
25850 33.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
16288 34.REMOVE NO. 4 WATER BY-PASS PIPE
16278 35.REMOVE NO. 2 WATER BY-PASS PIPE (w/o DPF)
23701 36.REMOVE INJECTION PIPE RH
23764A 37.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)
Disconnect the fuel hose.
Remove the fuel check valve, No. 4 nozzle leakage pipe and gasket.
23702 38.REMOVE INJECTION PIPE LH
23706 39.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY
23239D 40.REMOVE NO. 1 FUEL HOSE (w/o DPF)
23805B 41.REMOVE NO. 5 FUEL PIPE SUB-ASSEMBLY (w/o DPF)
23705 42.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY
23810A 43.REMOVE COMMON RAIL ASSEMBLY RH
w/ DPF:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>REMOVAL
w/o DPF:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/o DPF)>REMOVAL
23812D 44.REMOVE NO. 2 FUEL PIPE (w/ DPF)
23765 45.REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)
23820A 46.REMOVE COMMON RAIL ASSEMBLY LH
w/ DPF:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>REMOVAL
w/o DPF:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/o DPF)>REMOVAL
23801L 47.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
25800 48.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ DPF)
25614 49.REMOVE NO. 4 EGR PIPE (w/o DPF)
27148B 50.REMOVE CONNECTING WIRE (w/ DPF)
Detach the 2 clamps and remove the connecting wire.
23763 51.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)
17113 52.REMOVE INTAKE PIPE
17114D 53.REMOVE NO. 3 INTAKE MANIFOLD
16289 54.DISCONNECT NO. 5 WATER BY-PASS PIPE (w/o DPF)
25601 55.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)
25602 56.REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY (w/o DPF)
25680 57.REMOVE EGR COOLER ASSEMBLY WITH NO. 2 EGR VALVE ASSEMBLY (w/ DPF)
25620 58.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER ASSEMBLY (w/o DPF)
23764A 59.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)
23763 60.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)
Remove the union bolt and gasket.
Remove the bolt and disconnect the No. 3 nozzle leakage pipe.
23901H 61.REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)
23762B 62.REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)
23761A 63.REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)
23881D 64.REMOVE FUEL HOSE BRACKET (w/ DPF)
Remove the bolt and fuel hose bracket.
23841C 65.REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)
16268 66.REMOVE NO. 1 WATER BY-PASS PIPE (w/ DPF)
67.REMOVE STARTER HOSE BRACKET SUB-ASSEMBLY
Disconnect the 2 starter hoses from the starter assembly and starter hose bracket sub-assembly.
Remove the 2 bolts and starter hose bracket sub-assembly.
17111 68.REMOVE NO. 1 INTAKE MANIFOLD
17112 69.REMOVE NO. 2 INTAKE MANIFOLD
19871 70.REMOVE NO. 1 GLOW PLUG CONNECTOR
82112 71.REMOVE NO. 2 ENGINE ROOM WIRE
Disconnect the starter assembly connector.
Remove the nut and disconnect the starter assembly wire harness.
Detach the No. 2 engine room wire clamp.
Remove the bolt and No. 2 engine room wire.
37140 72.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110 73.REMOVE REAR PROPELLER SHAFT ASSEMBLY
74.REMOVE MANUAL TRANSMISSION WITH TRANSFER
12281A 75.INSTALL ENGINE HANGER
Install the No. 1 and No. 2 engine hangers with the 4 bolts shown in the illustration.
| No. 1 Engine Hanger | 12281-51040 |
| No. 2 Engine Hanger | 12282-51040 |
| Bolt | 91671-80825 |
| *A | for Bank 1 | *B | for Bank 2 |
| *1 | No. 1 Engine Hanger | *2 | No. 2 Engine Hanger |
76.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
| *A | for Bank 1 |
| *B | for Bank 2 |
Remove the 2 nuts and 2 plate washers from the front engine mounting insulator LH and RH.
Lift the engine assembly out of the vehicle carefully.
Make sure the engine assembly is clear of all wiring and hoses.
Place the engine assembly onto a workbench.
31210 77.REMOVE CLUTCH COVER ASSEMBLY
31250 78.REMOVE CLUTCH DISC ASSEMBLY
33311W 79.INSPECT INPUT SHAFT BEARING
33311W 80.REPLACE INPUT SHAFT BEARING
13405 81.REMOVE FLYWHEEL SUB-ASSEMBLY
| *1 | Crankshaft Pulley |
| *a | Protective Tape |
Using SST, hold the crankshaft pulley.
To prevent damage to the crankshaft pulley, apply protective tape to the contact areas of SST and the crankshaft pulley before performing this procedure.
Remove the 8 bolts and flywheel sub-assembly.
82.INSTALL ENGINE ASSEMBLY ON ENGINE STAND
Install the engine assembly onto an engine stand with the bolts.
12281A 83.REMOVE ENGINE HANGER
Remove the 4 bolts and No. 1 and No. 2 engine hangers.
12361 84.REMOVE FRONT ENGINE MOUNTING INSULATOR RH
| *A | for Bank 1 |
| *B | for Bank 2 |
Remove the nut, front engine mounting insulator RH and engine mounting stabilizer.
12361 85.REMOVE FRONT ENGINE MOUNTING INSULATOR LH
Remove the nut, front engine mounting insulator LH and engine mounting stabilizer.
12371 86.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Remove the 4 bolts and rear No. 1 engine mounting insulator from the manual transmission with transfer.