Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P1271  Fuel Regulator Circuit (EDU Drive)  P1272  Fuel Pressure Regulator Malfunction  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

For more information on the injector driver, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



A208468E09
3.719,2.781 3.49,2.781 false 3.667,3 3.479,3.135 3.479,3.135 3.396,3.135 false 3.896,2.427 4.083,2.229 4.083,2.229 4.188,2.229 false 0.052,0.031 4.219,0.313 4.167,0.281 10 false Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.927,0.375 2.042,0.771 1.115,0.396 10 false Accelerator Pedal Opening Angle 0.385,1.385 2.042,1.688 1.656,0.302 10 false Pressure Discharge Valve 1.125,2.292 2.094,2.573 0.969,0.281 10 false Fuel Pressure 2.604,0.542 2.99,0.76 0.385,0.219 10 false Open 4.188,1.406 4.646,1.656 0.458,0.25 10 false Open 2.594,1.188 3.146,1.521 0.552,0.333 10 false Closed 4.135,0.75 4.708,1.01 0.573,0.26 10 false Closed 4.25,2.135 6.229,2.375 1.979,0.24 10 false w/o Pressure Discharge Valve 1.688,2.688 3.552,2.938 1.865,0.25 10 false w/ Pressure Discharge Valve 2.073,3.042 3.5,3.26 1.427,0.219 10 false Target Fuel Pressure 3.979,3.281 5.125,3.521 1.146,0.24 10 false Time Reduction 3.427,3.552 3.792,3.76 0.365,0.208 10 false Time

A205138E01
6.795,2.675 7.136,2.779 0.341,0.105 0.042,0.073 3.564,0.248 3.522,0.175 10 Cross Section Diagram of Pressure Discharge Valve: 0.538,1.648 1.764,1.998 1.226,0.351 10 From Common Rail (High Pressure) 1.877,0.475 4.355,0.663 2.478,0.189 10 Return to Fuel Tank (Low Pressure) 3.044,2.426 3.413,2.596 0.369,0.17 10 Valve 5.299,1.685 5.882,1.856 0.582,0.17 10 Solenoid 3.448,1.802 2.859,2.5 2.859,2.5 2.977,2.5 false 4.252,2.12 5.1,1.764 5.1,1.764 5.254,1.764 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1271 Fuel Regulator Circuit Malfunction (EDU Drive) Either condition is met (1 trip detection logic):
·

Open or short in pressure discharge valve circuit.

·

There is no valve opening confirmation (INJF) signal from the injector driver to the ECM for a specific number of times consecutively despite the ECM sending valve opening command (PRD) signals after the engine is started.


·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve (common rail assembly (for bank 2))

·

Injector driver


Comes on DTC stored
P1272 Fuel Pressure Regulator Malfunction Pressure discharge valve does not open.
Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off (2 trip detection logic).
·

Open or short in pressure discharge valve circuit (P1271 is stored simultaneously)

·

Pressure discharge valve (common rail assembly (for bank 2))

·

Injector driver

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1271
·

Common Rail Pressure

·

Target Common Rail Pressure

·

Pressure discharge valve


P1272

HINT:
·

After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail by entering the following menus:

Powertrain / Engine / Data List / Common Rail Pressure.

·

P1271:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not output.

·

P1272:

After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.


Reference
Engine Speed Fuel Pressure (kPa)
Idling Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure
2500 rpm (No engine load)


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1271 Engine switch on (IG) to off and drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal
P1272 Ignition switch ON to off

MONITOR DESCRIPTION

P1271 (Open or short in pressure discharge valve circuit):

This DTC will be stored if there is no valve opening confirmation (RLF) signal sent from the injector driver to the ECM despite the ECM commanding the injector driver to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.

The injector driver monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the injector driver interprets this as the INJF signal being low. If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

A208469E45
3.854,2.771 3.969,2.51 3.969,2.51 4.125,2.51 false 3.854,3.115 3.781,3.396 3.781,3.396 3.646,3.396 false 0.115,0.052 1.438,0.208 1.323,0.156 10 false P1271 Malfunction: 0.188,1.906 1.844,2.271 1.656,0.365 10 false Pressure Discharge Valve Command Signal 1.979,1.969 2.354,2.156 0.375,0.188 10 false PRD 2.344,0.198 2.719,0.385 0.375,0.188 10 false ECM 5.5,0.198 6.469,0.385 0.969,0.188 10 false Injector Driver 2.833,1.365 3.104,1.552 0.271,0.188 10 false On 3.292,1.76 3.542,1.948 0.25,0.188 10 false Off 4.156,2.406 4.927,2.594 0.771,0.188 10 false Abnormal 3.167,3.302 3.698,3.49 0.531,0.188 10 false Normal 0.177,2.625 1.833,2.99 1.656,0.365 10 false Pressure Discharge Valve Confirmation Signal 1.99,2.698 2.344,2.885 0.354,0.188 10 false RLF 3.385,1.198 5.25,1.417 1.865,0.219 10 false Confirmation Signal (RLF) 3.365,0.479 5.323,0.667 1.958,0.188 10 false Command Signal (PRD)


P1272 (Pressure discharge valve stuck closed):

The pressure discharge valve will open and discharge the internal fuel pressure from the common rail to the fuel tank when the ignition switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then determines that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the ignition switch has been turned off.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A531277E01
1.021,0.896 1.479,1.094 0.458,0.198 10 false RLF 1,1.354 1.458,1.552 0.458,0.198 10 false PRD 5.865,1.344 6.323,1.542 0.458,0.198 10 false PRD 5.885,0.885 6.344,1.083 0.458,0.198 10 false RLFF 0.979,1.771 1.438,1.969 0.458,0.198 10 false RLF+ 0.958,2.74 1.417,2.938 0.458,0.198 10 false RLF- 1.385,0.896 1.844,1.094 0.458,0.198 10 false C122 0.521,3.094 1.583,3.302 1.063,0.208 10 false Injector Driver 3.708,1.938 4.167,2.135 0.458,0.198 10 false v1 3.688,2.104 5.427,2.333 1.74,0.229 10 false Pressure Discharge Valve 6.042,3.104 6.5,3.302 0.458,0.198 10 false C39 6.042,3.26 6.5,3.458 0.458,0.198 10 false ECM 5.583,1.25 6.042,1.448 0.458,0.198 10 false 54 5.573,0.76 6.031,0.958 0.458,0.198 10 false 32 1.51,0.698 1.969,0.896 0.458,0.198 10 false 8 1.51,1.146 1.969,1.344 0.458,0.198 10 false 4 1.49,1.594 1.948,1.792 0.458,0.198 10 false 2 1.51,2.521 1.969,2.719 0.458,0.198 10 false 1 5.229,1.688 5.688,1.885 0.458,0.198 10 false 1 4.188,1.677 4.646,1.875 0.458,0.198 10 false 2 2.688,1.552 3.146,1.75 0.458,0.198 10 false * 4.063,3.167 5.125,3.375 1.063,0.208 10 false *: Shielded 1.385,1.354 1.844,1.552 0.458,0.198 10 false C122 1.375,1.781 1.833,1.979 0.458,0.198 10 false C121 1.396,2.74 1.854,2.938 0.458,0.198 10 false C121 4.354,1.771 4.813,1.969 0.458,0.198 10 false RLV 4.76,1.771 5.219,1.969 0.458,0.198 10 false COM3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:
·

After completing repairs, confirm that P1271 and/or P1272 does not recur.

·

If P062D (No. 1 injector driver) and P1271 are present simultaneously, there is an open in the INJF wire harness between the injector driver and ECM, or there is an open in the wire harness for both an fuel injector and the pressure discharge valve.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Read the pending DTCs.

Result:
Result Proceed to
P1272 A
P1271 B
P1271 and P1272 B
Other DTCs output C




A

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)

B

6.INSPECT COMMON RAIL ASSEMBLY (FOR BANK 2)(PRESSURE DISCHARGE VALVE RESISTANCE)

C

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain /Engine / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 234 2109

d.

Select "Close to Open Check".


e.

Read the value of "Open and Engine OFF".

OK:

0.5 MPa or less


HINT:
·

When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.

·

When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.

·

When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.

·

Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.




Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 2)
3.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 2)
a.

Replace the common rail assembly (for Bank 2).

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.BLEED AIR FROM FUEL SYSTEM
4.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.




Result:
Proceed to
NEXT



NEXT

END

6.INSPECT COMMON RAIL ASSEMBLY (FOR BANK 2)(PRESSURE DISCHARGE VALVE RESISTANCE)
a.

Inspect the common rail assembly (for Bank 2).

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER)

NG

3.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 2)
7.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER)
a.

Disconnect the injector driver connector.


b.

Disconnect the pressure discharge valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v1-2 (COM3) - C121-2 (RLF+) Always Below 1 Ω
v1-1 (RLV) - C121-1 (RLF-) Always Below 1 Ω
v1-2 (COM3) or C121-2 (RLF+) - Body ground Always 10 kΩ or higher
v1-1 (RLV) or C121-1 (RLF-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER)
a.

Disconnect the injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C122-4 (PRD) - C39-54 (PRD) Always Below 1 Ω
C122-8 (INJF) - C39-32 (RLFF) Always Below 1 Ω
C122-4 (PRD) or C39-54 (PRD) - Body ground Always 10 kΩ or higher
C122-8 (INJF) or C39-32 (RLFF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT INJECTOR DRIVER (POWER SOURCE CIRCUIT)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.INSPECT INJECTOR DRIVER (POWER SOURCE CIRCUIT)
a.
A204910C23
0.49,1.021 0.896,1.281 0.406,0.26 1.417,0.99 0.927,0.458 true 1.406,1.438 0.969,1.635 true 0.729,1.594 1.021,1.813 0.292,0.219 10 false +B 0.604,0.365 0.99,0.583 0.385,0.219 10 false GND 0.229,0.208 0.406,0.365 0.177,0.156 10 false *a 0.531,1.063 1.063,1.219 0.531,0.156 10 false C124
*a Front view of wire harness connector
(to Injector Driver)


Disconnect the injector driver connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C124-3 (+B) - C124-1 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.REPLACE INJECTOR DRIVER

NG

13.GO TO INJECTOR CIRCUIT
10.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
11.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

Result:
Tester Display Result Proceed to
Pending DTC P1271 and/or P1272 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





A

END

B

14.REPLACE ECM
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.GO TO INJECTOR CIRCUIT

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED