Refer to the description for DTC P1C8949.
Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>P1C8949
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1C8B49 | Park Pawl Motor Control System (Switching Control Lock/Unlock) Internal Electronic Failure | When the ignition switch is ON, and while the shift state is being changed between park (P) and a shift state other than park (P), the power supply voltage is low, an open or short occurs in the P CON MTR relay, shift control actuator assembly (parking lock motor and rotation angle sensor) or wire harness, and an internal malfunction occurs in the shift control actuator assembly (parking lock motor and rotation angle sensor) continuously for 2 seconds or more.
(1 trip detection logic) |
·
Shift control ECU ·
Auxiliary battery ·
Shift control supply ·
Shift control actuator assembly ·
FCV transaxle with motor assembly ·
P CON MTR relay ·
Wire harness or connector |
·
Master Warning -
Comes on ·
Multi-information Display Error Message -
Displayed |
EV | A |
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ | ○ |
| While the shift state is being changed between park (P) and a shift state other than park (P) | ○ | ○ | ○ | ○ | |
| Malfunction Status | Power supply voltage is low | ○ | - | - | - |
| P CON MTR relay open | - | ○ | - | - | |
| P CON MTR relay short | - | - | ○ | - | |
| Shift control actuator assembly (parking lock motor and rotation angle sensor) open | - | - | - | ○ | |
| Detection Time | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 5 | Pattern 6 | Pattern 7 | Pattern 8 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ | ○ |
| While the shift state is being changed between park (P) and a shift state other than park (P) | ○ | ○ | ○ | ○ | |
| Malfunction Status | Shift control actuator assembly (parking lock motor and rotation angle sensor) short | ○ | - | - | - |
| Wire harness open | - | ○ | - | - | |
| Wire harness short | - | - | ○ | - | |
| Internal malfunction occurs in the shift control actuator assembly (parking lock motor and rotation angle sensor) | - | - | - | ○ | |
| Detection Time | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.
Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY
Turn the ignition switch to ON.
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Refer to the wiring diagram for DTC P1C8949.
Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>P1C8949
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.
Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs in the table below are output | A |
| P1C8B49 and any DTCs in the table below are output | B |
| Priority | Relevant DTC | |
|---|---|---|
| 1 | P085D94 | Gear Shift Control Module "A" Unexpected Operation |
| P1761A2 | Gear Shift Control Module "A" System Voltage Low | |
| P1765A2 | Sub Battery Module System Voltage Low | |
| P176D12 | IG2 Signal (Gear Shift Control Module "A") Circuit Short to Auxiliary Battery | |
| P176949 | Gear Shift Control Module "A" Internal Electronic Failure | |
| 2 | P1C8F14 | Park Pawl Motor Phase U Circuit Short to Ground or Open |
| P1C9414 | Park Pawl Motor Phase V Circuit Short to Ground or Open | |
| P1C9914 | Park Pawl Motor Phase W Circuit Short to Ground or Open | |
The chart above is listed in inspection order of priority.
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None
Procedure1
Check if the DTCs related to yaw rate sensor malfunction, acceleration sensor malfunction, or CAN bus malfunction are output from the electronically controlled brake system.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Turn the ignition switch to ON.
It may not be possible to turn the ignition switch to ON (READY).
Procedure1
Read the freeze frame data of DTC P1C8B49.
| Tester Display |
|---|
| BATT Voltage for Gear Shift Control Module |
| Result | Proceed to |
|---|---|
| The value of BATT Voltage for Gear Shift Control Module is 9 V or more | A |
| The value of BATT Voltage for Gear Shift Control Module is less than 9 V | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs and freeze frame data and then write them down.
When DTCs are cleared, the freeze frame data is also cleared. The freeze frame data stored when the DTCs are detected is required for troubleshooting. Therefore, check and record the stored DTC information before clearing them.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
Leave the vehicle as is for 60 seconds or more.
Do not connect the GTS.
Do not depress the brake pedal.
Do not open/close any of the doors.
NEXT
Charge the auxiliary battery.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Depress the brake pedal and move the shift lever to select neutral (N).
Check that the shift state is neutral (N), and then push the P position switch (parking switch) to select park (P).
Turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.
Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.
Stop the vehicle and push the P position switch (parking switch) to select park (P).
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 10 seconds or more.
It may not be possible to turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| Only P1C8B49 is output | A |
| DTCs are not output | B |
| P1C8B49 and other DTCs are output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Read the freeze frame data of DTC P1C8B49.
| Tester Display |
|---|
| Parking Lock Motor Main Relay Status |
| Parking Lock Motor Backup Relay Status |
| Result | Proceed to |
|---|---|
| The value of Parking Lock Motor Main Relay Status is ON | A |
| The value of Parking Lock Motor Backup Relay Status is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Read the freeze frame data of DTC P1C8B49.
| Tester Display |
|---|
| W Phase Parking Lock Motor Terminal Voltage |
| V Phase Parking Lock Motor Terminal Voltage |
| U Phase Parking Lock Motor Terminal Voltage |
| Tester Display | Specified Condition |
|---|---|
| W Phase Parking Lock Motor Terminal Voltage | 1 to 2 V |
| V Phase Parking Lock Motor Terminal Voltage | 1 to 2 V |
| U Phase Parking Lock Motor Terminal Voltage | 1 to 2 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Pre-procedure1
Disconnect the A44 shift control ECU connector.
Disconnect the G153 rotation angle sensor (shift control actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A44,G153)Location & Routingewd_type=routing;type=c,c;code=A44,G153 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=22,23,21,24 Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assemblyewd_type=component;type=c;code=G153;pinno=10,5,3,8 |
||
| A44-22 (VC) - G153-10 (RVC) | Always | Below 1 Ω |
| A44-23 (RA) - G153-5 (RA) | Always | Below 1 Ω |
| A44-21 (RB) - G153-3 (RB) | Always | Below 1 Ω |
| A44-24 (E2) - G153-8 (RE2) | Always | Below 1 Ω |
| A44-22 (VC) - G153-10 (RVC) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-23 (RA) or G153-5 (RA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-21 (RB) or G153-3 (RB) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-24 (E2) or G153-8 (RE2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the G153 rotation angle sensor (shift control actuator assembly) connector.
Reconnect the A44 shift control ECU connector.
OK
NG
Pre-procedure1
Disconnect the D93 shift control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D93)Location & Routingewd_type=routing;type=c;code=D93 Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D93;pinno=6,5,4 |
||
| D93-6 (E01) - Body ground | Always | Below 1 Ω |
| D93-5 (E02) - Body ground | Always | Below 1 Ω |
| D93-4 (E03) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the D93 shift control ECU connector.
OK
NG
Pre-procedure1
Check that the parking brake is applied.
Pull the shift control actuator assembly from the FCV with motor transaxle assembly.
Reconnect the G153 shift control actuator assembly connector.
Release the brake pedal and turn the ignition switch to ACC.
The shift control actuator assembly may operate if the ignition switch is turned to ON or ON (READY). Do not turn the ignition switch to ON or ON (READY) during this inspection to prevent the shift control actuator assembly from operating while in contact with the splines.
Procedure1
Using a screwdriver with its tip wrapped with protective tape or a piece of cloth, rotate the shaft.
During this inspection, make sure to use a screwdriver with its tip wrapped with protective tape or a piece of cloth to prevent the splines of the actuator from being damaged.
Rotate the shaft with torque of 2 N*m (20.3 kgf*cm, 17.7 in.*lbf) or less. Do not apply load while the contacting the stopper inside the actuator.
The shift control actuator assembly cannot be disassembled.
Confirm that the shaft of the shift control actuator assembly rotates smoothly.
The shaft of the shift control actuator assembly rotates smoothly.
| *a | Component with harness connected
(Shift Control ECU) |
| *b | Output Waveform while Splines of Shift Control Actuator Assembly being Rotated (Example) |
Measure the voltage according to the value(s) in the table below.
When measuring the voltage, turn the shift control actuator assembly slowly.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A44)Location & Routingewd_type=routing;type=c;code=A44 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=23,24,21 |
||
| A44-23 (RA) -A44-24 (E2) | Ignition switch ACC, shaft of shift control actuator assembly being rotated | 0 to 1.5 V ←→ 4 to 5.5 V |
| A44-21 (RB) -A44-24 (E2) | Ignition switch ACC, shaft of shift control actuator assembly being rotated | 0 to 1.5 V ←→ 4 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Pre-procedure1
Disconnect the A44 shift control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A44)Location & Routingewd_type=routing;type=c;code=A44 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=22,23,21,24 |
||
| A44-22 (VC) - A44-23 (RA) | Ignition switch off | 10 kΩ or higher |
| A44-22 (VC) - A44-21 (RB) | Ignition switch off | 10 kΩ or higher |
| A44-22 (VC) - A44-24 (E2) | Ignition switch off | 590 to 670 Ω |
| A44-23 (RA) - A44-21 (RB) | Ignition switch off | 10 kΩ or higher |
| A44-23 (RA) - A44-24 (E2) | Ignition switch off | 10 kΩ or higher |
| A44-21 (RB) - A44-24 (E2) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A44 shift control ECU connector.
OK
NG
Pre-procedure1
None
Procedure1
Wrap the shaft with a piece of cloth and turn it using pliers.
The shaft rotates smoothly in the lock and unlock directions.
Rotate the shaft using torque between 4.0 and 7.0 N*m (41 and 71 kgf*cm, 36 and 61 in.*lbf).
During this inspection, make sure to use a piece of cloth to prevent the shaft splines from being damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Set the shaft in the lock position after the inspection.
OK
NG
Charge the auxiliary battery.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs and freeze frame data and then write them down.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
Leave the vehicle as is for 60 seconds or more.
Do not connect the GTS.
Do not depress the brake pedal.
Do not open/close any of the doors.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Depress the brake pedal and move the shift lever to select neutral (N).
Check that the shift state is neutral (N), and then push the P position switch (parking switch) to select park (P).
Turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.
Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.
Stop the vehicle and push the P position switch (parking switch) to select park (P).
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 10 seconds or more.
It may not be possible to turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Only P1C8B49 is output | B |
| P1C8B49 and other DTCs are output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
| *1 | Luggage Room Relay Block |
| *2 | P CON MTR Relay |
Remove the P CON MTR relay from the luggage room relay block.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| P CON MTR relay terminal 3 or 2 - Body ground | Ignition switch off | 8 to 15.4 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the P CON MTR relay.
OK
NG
Pre-procedure1
| *1 | Luggage Room Relay Block |
| *2 | P CON MTR Relay |
Remove the P CON MTR relay from the luggage room relay block.
Procedure1
| *1 | P CON MTR Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the P CON MTR relay.
OK
NG
Pre-procedure1
Disconnect the G153 parking lock motor (shift control actuator assembly) connector.
Remove the P CON MTR relay from the luggage room relay block.
Disconnect the A44 shift control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G153,A44)Location & Routingewd_type=routing;type=c,c;code=G153,A44 Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assemblyewd_type=component;type=c;code=G153;pinno=7 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=12 |
||
| P CON MTR relay terminal 5 - G153-7 (BMA) | Always | Below 1 Ω |
| P CON MTR relay terminal 1 - A44-12 (BMA1) | Always | Below 1 Ω |
| P CON MTR relay terminal 5 or G153-7 (BMA)- Body ground and other terminals | Always | 10 kΩ or higher |
| P CON MTR relay terminal 1 or A44-12 (BMA1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A44 shift control ECU connector.
Install the P CON MTR relay.
Reconnect the G153 parking lock motor (shift control actuator assembly) connector.
OK
NG
Pre-procedure1
Disconnect the A44 shift control ECU connector.
Disconnect the G153 parking lock motor (shift control actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A44,G153)Location & Routingewd_type=routing;type=c,c;code=A44,G153 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=5,2,1 Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assemblyewd_type=component;type=c;code=G153;pinno=2,6,1 |
||
| A44-5 (MUA) - G153-2 (MUA) | Always | Below 1 Ω |
| A44-2 (MVA) - G153-6 (MVA) | Always | Below 1 Ω |
| A44-1 (MWA) - G153-1 (MWA) | Always | Below 1 Ω |
| A44-5 (MUA) or G153-2 (MUA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-2 (MVA) or G153-6 (MVA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-1 (MWA) or G153-1 (MWA) -Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the G153 parking lock motor (shift control actuator assembly) connector.
Reconnect the A44 shift control ECU connector.
OK
NG
Pre-procedure1
| *1 | Parking Lock Motor (Shift Control Actuator Assembly) |
Disconnect the parking lock motor (shift control actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (MUA) - 7 (BMA) | Always | 0.5 to 2 Ω |
| 6 (MVA) - 7 (BMA) | Always | 0.5 to 2 Ω |
| 1 (MWA) - 7 (BMA) | Always | 0.5 to 2 Ω |
| 2 (MUA) - 6 (MVA) | Always | 1 to 4 Ω |
| 6 (MVA) - 1 (MWA) | Always | 1 to 4 Ω |
| 1 (MWA) - 2 (MUA) | Always | 1 to 4 Ω |
| 2 (MUA) - Body ground | Always | 10 kΩ or higher |
| 6 (MVA) - Body ground | Always | 10 kΩ or higher |
| 1 (MWA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the parking lock motor (shift control actuator assembly) connector.
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the cable from the positive (+) auxiliary battery terminal.
Remove the P CON MTR relay from the luggage room relay block.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) cable - P CON MTR relay terminal 3 or 2 | Always | Below 1 Ω |
| Auxiliary battery positive (+) cable or P CON MTR relay terminal 3 or 2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the P CON MTR relay.
Reconnect the cable to the positive (+) auxiliary battery terminal.
Reconnect the cable to the negative (-) auxiliary battery terminal.
OK
NG
Charge the auxiliary battery.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs and freeze frame data and then write them down.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
Leave the vehicle as is for 60 seconds or more.
Do not connect the GTS.
Do not depress the brake pedal.
Do not open/close any of the doors.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Depress the brake pedal and move the shift lever to select neutral (N).
Check that the shift state is neutral (N), and then push the P position switch (parking switch) to select park (P).
Turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.
Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.
Stop the vehicle and push the P position switch (parking switch) to select park (P).
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 10 seconds or more.
It may not be possible to turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Only P1C8B49 is output | B |
| P1C8B49 and other DTCs are output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Read the freeze frame data of DTC P1C8B49.
| Tester Display |
|---|
| W Phase Parking Lock Motor Terminal Voltage |
| V Phase Parking Lock Motor Terminal Voltage |
| U Phase Parking Lock Motor Terminal Voltage |
| Tester Display | Specified Condition |
|---|---|
| W Phase Parking Lock Motor Terminal Voltage | 1 to 2 V |
| V Phase Parking Lock Motor Terminal Voltage | 1 to 2 V |
| U Phase Parking Lock Motor Terminal Voltage | 1 to 2 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Pre-procedure1
| *1 | Luggage Room Relay Block |
| *2 | P CON MTR Relay |
Remove the P CON MTR relay from the luggage room relay block.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| P CON MTR relay terminal 3 or 2 - Body ground | Ignition switch off | 8 to 15.4 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the P CON MTR relay.
OK
NG
Pre-procedure1
| *1 | Luggage Room Relay Block |
| *2 | P CON MTR Relay |
Remove the P CON MTR relay from the luggage room relay block.
Procedure1
| *1 | P CON MTR Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the P CON MTR relay.
OK
NG
Pre-procedure1
Disconnect the G153 parking lock motor (shift control actuator assembly) connector.
Remove the P CON MTR relay from the luggage room relay block.
Disconnect the A44 shift control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G153,A44)Location & Routingewd_type=routing;type=c,c;code=G153,A44 Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assemblyewd_type=component;type=c;code=G153;pinno=7 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=12 |
||
| P CON MTR relay terminal 5 - G153-7 (BMA) | Always | Below 1 Ω |
| P CON MTR relay terminal 1 - A44-12 (BMA1) | Always | Below 1 Ω |
| P CON MTR relay terminal 5 or G153-7 (BMA) - Body ground and other terminals | Always | 10 kΩ or higher |
| P CON MTR relay terminal 1 or A44-12 (BMA1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A44 shift control ECU connector.
Install the P CON MTR relay.
Reconnect the G153 parking lock motor (shift control actuator assembly) connector.
OK
NG
Pre-procedure1
Disconnect the A44 shift control ECU connector.
Disconnect the G153 parking lock motor (shift control actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A44,G153)Location & Routingewd_type=routing;type=c,c;code=A44,G153 Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECUewd_type=component;type=c;code=A44;pinno=5,2,1 Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assemblyewd_type=component;type=c;code=G153;pinno=2,6,1 |
||
| A44-5 (MUA) - G153-2 (MUA) | Always | Below 1 Ω |
| A44-2 (MVA) - G153-6 (MVA) | Always | Below 1 Ω |
| A44-1 (MWA) - G153-1 (MWA) | Always | Below 1 Ω |
| A44-5 (MUA) or G153-2 (MUA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-2 (MVA) or G153-6 (MVA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A44-1 (MWA) or G153-1 (MWA) -Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A44 shift control ECU connector.
Reconnect the G153 parking lock motor (shift control actuator assembly) connector.
OK
NG
Pre-procedure1
Disconnect the G12 shift control supply connector.
Disconnect the D92 shift control ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G12,D92)Location & Routingewd_type=routing;type=c,c;code=G12,D92 Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supplyewd_type=component;type=c;code=G12;pinno=16,3,7,2 Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D92;pinno=27,22 |
||
| G12-16 (IG) - D92-27 (IG2) | Always | Below 1 Ω |
| G12-3 (RO) - D92-22 (BUBI) | Always | Below 1 Ω |
| CAPACITOR fuse terminal 2 - G12-7 (+B) | Always | Below 1 Ω |
| G12-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the D92 shift control ECU connector.
Reconnect the G12 shift control supply connector.
OK
NG
Pre-procedure1
| *1 | Parking Lock Motor (Shift Control Actuator Assembly) |
Disconnect the parking lock motor (shift control actuator assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (MUA) - 7 (BMA) | Always | 0.5 to 2 Ω |
| 6 (MVA) - 7 (BMA) | Always | 0.5 to 2 Ω |
| 1 (MWA) - 7 (BMA) | Always | 0.5 to 2 Ω |
| 2 (MUA) - 6 (MVA) | Always | 1 to 4 Ω |
| 6 (MVA) - 1 (MWA) | Always | 1 to 4 Ω |
| 1 (MWA) - 2 (MUA) | Always | 1 to 4 Ω |
| 2 (MUA) - Body ground | Always | 10 kΩ or higher |
| 6 (MVA) - Body ground | Always | 10 kΩ or higher |
| 1 (MWA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the parking lock motor (shift control actuator assembly) connector.
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the cable from the positive (+) auxiliary battery terminal.
Remove the P CON MTR relay from the luggage room relay block.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) cable - P CON MTR relay terminal 3 or 2 | Always | Below 1 Ω |
| Auxiliary battery positive (+) cable or P CON MTR relay terminal 3 or 2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the P CON MTR relay.
Reconnect the cable to the positive (+) auxiliary battery terminal.
Reconnect the cable to the negative (-) auxiliary battery terminal.
OK
NG
Charge the auxiliary battery.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs and freeze frame data and then write them down.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
Leave the vehicle as is for 60 seconds or more.
Do not connect the GTS.
Do not depress the brake pedal.
Do not open/close any of the doors.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Depress the brake pedal and move the shift lever to select neutral (N).
Check that the shift state is neutral (N), and then push the P position switch (parking switch) to select park (P).
Turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.
Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.
Stop the vehicle and push the P position switch (parking switch) to select park (P).
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 10 seconds or more.
It may not be possible to turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Only P1C8B49 is output | B |
| P1C8B49 and other DTCs are output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the cable from the positive (+) auxiliary battery terminal.
Disconnect the G12 shift control supply connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G12)Location & Routingewd_type=routing;type=c;code=G12 Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supplyewd_type=component;type=c;code=G12;pinno=7 |
||
| Auxiliary battery positive (+) cable - G12-7 (+B) | Always | Below 1 Ω |
| Auxiliary battery positive (+) cable or G12-7 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the G12 shift control supply connector.
Reconnect the cable to the positive (+) auxiliary battery terminal.
Reconnect the cable to the negative (-) auxiliary battery terminal.
OK
for LHD: Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT CONTROL POWER SUPPLY (for LHD)>REMOVAL
for RHD: Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT CONTROL POWER SUPPLY (for RHD)>REMOVAL
NG
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Check for DTCs and freeze frame data and then write them down.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
Leave the vehicle as is for 60 seconds or more.
Do not connect the GTS.
Do not depress the brake pedal.
Do not open/close any of the doors.
NEXT
Pre-procedure1
Turn the ignition switch off.
Depress the brake pedal and move the shift lever to select neutral (N).
Check that the shift state is neutral (N), and then push the P position switch (parking switch) to select park (P).
Turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.
Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.
Stop the vehicle and push the P position switch (parking switch) to select park (P).
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 10 seconds or more.
It may not be possible to turn the ignition switch to ON (READY).
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Only P1C8B49 is output | B |
| P1C8B49 and other DTCs are output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
| Proceed to |
|---|
| NEXT |
NEXT