Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Rack and pinion power steering gear assembly

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

Airbag sensor assembly

·

Steering sensor

·

No. 1 global CAN junction connector

·

No. 3 global CAN junction connector

·

No. 4 global CAN junction connector



WIRING DIAGRAM

C441469E01
0.167,1 1.917,1.333 1.75,0.333 10 false Airbag ECU Assembly 0.208,5.875 1.625,6.406 1.417,0.531 10 false Central Gateway ECU (Network Gateway ECU) 5.49,2.354 7.156,2.917 1.667,0.563 10 false Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) 5.115,0.99 7.115,1.365 2,0.375 10 false Rack and Pinion Power Steering Gear Assembly 0.74,0.26 1.219,0.438 0.479,0.177 10 false CAFH 0.76,0.625 1.24,0.802 0.479,0.177 10 false CAFL 1.219,0.115 1.698,0.292 0.479,0.177 10 false 26 1.229,0.5 1.708,0.677 0.479,0.177 10 false 27 6.333,0.167 6.813,0.344 0.479,0.177 10 false CANH 6.344,0.656 6.823,0.833 0.479,0.177 10 false CANL 5.813,0.146 6.292,0.323 0.479,0.177 10 false 10 5.844,0.5 6.323,0.677 0.479,0.177 10 false 11 1.208,2.375 1.688,2.552 0.479,0.177 10 false 3 1.208,2.771 1.688,2.948 0.479,0.177 10 false 8 0.698,2.479 1.177,2.656 0.479,0.177 10 false CANH 0.771,2.844 1.25,3.021 0.479,0.177 10 false CANL 0.198,0.844 0.677,1.021 0.479,0.177 10 false D10 6.135,1.719 6.615,1.896 0.479,0.177 10 false CA1H 6.188,2.042 6.667,2.219 0.479,0.177 10 false CA1L 5.854,1.583 6.333,1.76 0.479,0.177 10 false 38 5.854,1.958 6.333,2.135 0.479,0.177 10 false 39 5.531,2.188 6.01,2.365 0.479,0.177 10 false A5 5.125,0.823 5.604,1 0.479,0.177 10 false A79 2.156,5.917 4.594,6.115 2.438,0.198 10 false No. 4 global CAN Junction Connector 2.26,4.906 2.74,5.083 0.479,0.177 10 false 2 2.25,5.313 2.729,5.49 0.479,0.177 10 false 6 2.24,0.479 2.719,0.656 0.479,0.177 10 false 8 2.25,0.115 2.729,0.292 0.479,0.177 10 false 4 2.948,0.885 3.427,1.063 0.479,0.177 10 false 2 2.938,1.281 3.417,1.458 0.479,0.177 10 false 6 2.271,3.938 2.75,4.115 0.479,0.177 10 false 1 2.271,4.302 2.75,4.479 0.479,0.177 10 false 5 2.969,0.5 3.448,0.677 0.479,0.177 10 false 5 2.958,0.104 3.438,0.281 0.479,0.177 10 false 1 2.948,2.729 3.427,2.906 0.479,0.177 10 false 7 2.938,2.333 3.417,2.51 0.479,0.177 10 false 3 1.219,3.927 1.698,4.104 0.479,0.177 10 false 24 1.219,4.323 1.698,4.5 0.479,0.177 10 false 23 0.75,4.042 1.229,4.219 0.479,0.177 10 false CA2H 0.771,4.438 1.25,4.615 0.479,0.177 10 false CA2L 0.208,5.719 1.552,5.906 1.344,0.188 10 false D119 0.25,3.063 0.729,3.24 0.479,0.177 10 false D34 0.229,3.271 1.802,3.823 1.573,0.552 10 false Steering Sensor 2.146,5.75 2.625,5.927 0.479,0.177 10 false D165 4.167,4.094 5.281,4.646 1.115,0.552 10 false No. 1 global CAN Junction Connector 4.198,3.896 4.677,4.073 0.479,0.177 10 false A77 5.052,1.927 5.531,2.104 0.479,0.177 10 false 5 5.042,1.552 5.521,1.729 0.479,0.177 10 false 1 5.021,3.458 5.5,3.635 0.479,0.177 10 false 6 5.021,3.073 5.5,3.25 0.479,0.177 10 false 2 6.125,3.208 6.604,3.385 0.479,0.177 10 false CANH 6.156,3.563 6.635,3.74 0.479,0.177 10 false CANL 5.833,3.104 6.313,3.281 0.479,0.177 10 false 27 5.833,3.469 6.313,3.646 0.479,0.177 10 false 43 5.646,3.792 6.125,3.969 0.479,0.177 10 false A6 5.615,3.958 7.083,4.521 1.469,0.563 10 false Brake Actuator Bracket Assembly (No. 2 Skid Control ECU) 4.333,0.135 4.813,0.313 0.479,0.177 10 false 3 4.344,0.51 4.823,0.688 0.479,0.177 10 false 7 5.021,0.115 5.5,0.292 0.479,0.177 10 false 4 5.021,0.51 5.5,0.688 0.479,0.177 10 false 8 2.26,2.375 2.74,2.552 0.479,0.177 10 false 4 2.25,2.74 2.729,2.917 0.479,0.177 10 false 8 0.646,5.479 1.125,5.656 0.479,0.177 10 false CAVL 0.646,4.917 1.125,5.094 0.479,0.177 10 false CAVH 1.208,4.896 1.688,5.073 0.479,0.177 10 false 10 1.208,5.292 1.688,5.469 0.479,0.177 10 false 11

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C99
1.51,0.073 1.927,0.323 0.417,0.25 2.479,1.969 2.365,1.969 2.365,1.969 2.208,0.896 true 2.75,1.771 2.635,1.771 2.635,1.771 2.302,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.573,0.125 2.031,0.323 0.458,0.198 10 false D119 2.573,1.917 3.042,2.135 0.469,0.219 10 false CA2H 2.865,1.688 3.427,1.938 0.563,0.25 10 false CA2L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

D119-24 (CA2H) - D119-23 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

53.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C425195C99
1.51,0.073 1.927,0.323 0.417,0.25 2.479,1.969 2.365,1.969 2.365,1.969 2.208,0.896 true 2.75,1.771 2.635,1.771 2.635,1.771 2.302,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.573,0.125 2.031,0.323 0.458,0.198 10 false D119 2.573,1.917 3.042,2.135 0.469,0.219 10 false CA2H 2.865,1.688 3.427,1.938 0.563,0.25 10 false CA2L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

D119-24 (CA2H) - D119-23 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C421610C47
1.5,0.083 1.917,0.333 0.417,0.25 1.5,2.583 1.917,2.833 0.417,0.25 1.104,1.833 1.271,1.833 1.271,1.833 2.188,0.906 true 2.844,1.833 2.677,1.833 2.677,1.833 2.281,0.917 true 2.844,4.25 2.677,4.25 2.677,4.25 2.354,3.76 true 1.552,0.115 2.167,0.313 0.615,0.198 10 false D119 1.594,2.625 2.208,2.823 0.615,0.198 10 false D20 0.667,1.75 1.281,1.948 0.615,0.198 10 false CA2H 2.906,1.76 3.375,1.969 0.469,0.208 10 false CA2L 2.906,4.177 3.406,4.396 0.5,0.219 10 false BAT 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.208,2.49 0.521,2.646 0.313,0.156 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119,D20)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D119-24 (CA2H) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-23 (CA2L) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C421610C48
1.5,0.083 1.917,0.333 0.417,0.25 1.5,2.583 1.917,2.833 0.417,0.25 1.104,1.833 1.271,1.833 1.271,1.833 2.188,0.906 true 2.844,1.833 2.677,1.833 2.677,1.833 2.281,0.917 true 2.469,2.792 2.302,2.792 2.302,2.792 1.646,3.198 true 1.552,0.115 2.167,0.313 0.615,0.198 10 false D119 1.594,2.625 2.208,2.823 0.615,0.198 10 false D20 0.667,1.75 1.281,1.948 0.615,0.198 10 false CA2H 2.906,1.76 3.375,1.969 0.469,0.208 10 false CA2L 2.563,2.708 3.063,2.927 0.5,0.219 10 false CG 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.156,2.573 0.469,2.729 0.313,0.156 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119,D20)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D119-24 (CA2H) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-23 (CA2L) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A77 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-7 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-5 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR BRACKET ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR BRACKET ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-6 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

NG

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-8 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the A77 No. 1 global CAN junction connector.


b.

Disconnect the D163 No. 3 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D163-5 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D163-6 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D163-8 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the D163 No. 3 global CAN junction connector.


b.

Disconnect the D165 No. 4 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-7 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-8 (CANL) - D20-4 (CG)

w/ Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-6 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/o Advanced Drive

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-5 (CANL) - D20-4 (CG)
D165-2 (CANH) - D20-4 (CG)* Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-6 (CANH) - D20-4 (CG)*



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the D34 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-8 (CANL) - D20-4 (CG)

w/ Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-6 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/o Advanced Drive

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-5 (CANL) - D20-4 (CG)
D165-2 (CANH) - D20-4 (CG)* Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D165-6 (CANH) - D20-4 (CG)*



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Disconnect the D10 airbag ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D163-8 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-5 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Disconnect the A6 brake actuator bracket assembly (No. 2 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-6 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Disconnect the A79 rack and pinion power steering gear assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A77-8 (CANL) - D20-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A77 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-7 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-5 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR BRACKET ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR BRACKET ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-6 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

NG

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-8 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the A77 No. 1 global CAN junction connector.


b.

Disconnect the D163 No. 3 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D163-5 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D163-6 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D163-8 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the D163 No. 3 global CAN junction connector.


b.

Disconnect the D165 No. 4 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-7 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-8 (CANL) - D20-16 (BAT)

w/ Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-6 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/o Advanced Drive

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-5 (CANL) - D20-16 (BAT)
D165-2 (CANH) - D20-16 (BAT)* Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-6 (CANH) - D20-16 (BAT)*



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the D34 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-8 (CANL) - D20-16 (BAT)

w/ Advanced Drive
Tester Connection Condition Specified Condition

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-6 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/o Advanced Drive

Click Location & Routing(D165,D20)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D165-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-5 (CANL) - D20-16 (BAT)
D165-2 (CANH) - D20-16 (BAT)* Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D165-6 (CANH) - D20-16 (BAT)*



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Disconnect the D10 airbag ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163,D20)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D163-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D163-8 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-5 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Disconnect the A6 brake actuator bracket assembly (No. 2 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-6 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Disconnect the A79 rack and pinion power steering gear assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77,D20)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A77-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A77-8 (CANL) - D20-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A77 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-3 (CANH) - A77-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-1 (CANH) - A77-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR BRACKET ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR BRACKET ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-2 (CANH) - A77-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

NG

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-4 (CANH) - A77-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the A77 No. 1 global CAN junction connector.


b.

Disconnect the D163 No. 3 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

D163-1 (CANH) - D163-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

D163-2 (CANH) - D163-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

D163-4 (CANH) - D163-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the D163 No. 3 global CAN junction connector.


b.

Disconnect the D165 No. 4 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-3 (CANH) - D165-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-4 (CANH) - D165-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-2 (CANH) - D165-6 (CANH) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the D34 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-4 (CANH) - D165-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-2 (CANH) - D165-6 (CANH) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Disconnect the D10 airbag ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

D163-4 (CANH) - D163-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-1 (CANH) - A77-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Disconnect the A6 brake actuator bracket assembly (No. 2 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-2 (CANH) - A77-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Disconnect the A79 rack and pinion power steering gear assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-4 (CANH) - A77-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

53.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A77 No. 1 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-3 (CANH) - A77-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

54.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

NG

56.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
54.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 GLOBAL CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A77)Location & Routing

Click Connector(A77)Instrument Panel>Front Compartment Main Wire>No. 1 Global CAN Junction Connector

A77-4 (CANH) - A77-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

55.CHECK FOR OPEN IN CAN BUS WIRE (RACK AND PINION POWER STEERING GEAR ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
55.CHECK FOR OPEN IN CAN BUS WIRE (RACK AND PINION POWER STEERING GEAR ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the A77 No. 1 global CAN junction connector.


b.

Disconnect the A79 rack and pinion power steering gear assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A79)Location & Routing

Click Connector(A79)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)

A79-10 (CANH) - A79-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (RACK AND PINION POWER STEERING GEAR ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

56.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the A77 No. 1 global CAN junction connector.


b.

Disconnect the D163 No. 3 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

D163-1 (CANH) - D163-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

57.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

57.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D163)Location & Routing

Click Connector(D163)Instrument Panel>Instrument Panel Wire>No. 3 Global CAN Junction Connector

D163-2 (CANH) - D163-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

58.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
58.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the D163 No. 3 global CAN junction connector.


b.

Disconnect the D165 No. 4 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-3 (CANH) - D165-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

59.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

59.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D165)Location & Routing

Click Connector(D165)Instrument Panel>Instrument Panel Wire>No. 4 Global CAN Junction Connector

D165-2 (CANH) - D165-6 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

60.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
60.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the D165 No. 4 global CAN junction connector.


b.

Disconnect the D119 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/o Advanced Drive

Click Location & Routing(D119)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

D119-10 (CAVH) - D119-11 (CAVL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)