Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1E1573  FC Positive and Negative Contactor Actuator Stuck Closed  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects an ON malfunction due to a high voltage relay (FRB, FRG, FRP) welded on or stuck on malfunction on the FC converter assembly side.

The cause of this malfunction may be one of the following:

FC converter assembly built in voltage pressure sensor (FVL) system malfunction
·

Voltage sensor (FVL) malfunction

·

FCDC converter control ECU malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

FC stack main relay (FRB, FRG) malfunction

·

FC precharge junction assembly (FRP) malfunction

·

No. 1 EV battery junction block assembly malfunction

·

FC converter power module transistor malfunction

·

Inverter with converter assembly malfunction


Shut down signal circuit malfunction
·

EV control ECU malfunction

·

Wire harness malfunction

·

Inverter with converter assembly malfunction

·

FCDC converter control ECU malfunction


Low-voltage circuit (12 V) malfunction
·

EV control ECU malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P1E1500.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E1500

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E1573 FC Positive and Negative Contactor Actuator Stuck Closed Internal inverter voltage has not decreased (this DTC is differentiated from P0C7600 based on the FVH value) even though it was discharged.
(1 trip detection logic)
·

FC stuck main relay (FRB)

·

FC stuck main relay (FRG)

·

FC precharge junction assembly (FRP)

·

No. 1 FC converter wire

·

No. 2 FC converter wire

·

FCDC converter control ECU board sub-assembly

·

FC converter power module transistor

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1E1573
·

FCDC Output Voltage

·

VH-Voltage after Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch off and wait for 10 minutes or more.

2.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

3.

Turn the ignition switch off and wait for 10 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV Battery High-Voltage Line Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

DTC P1E1573 is output, and when the following malfunction condition is met, the ignition switch will not be able to be turned to ON (READY).



PROCEDURE

1.CHECK DTC OUTPUT (EV, FCDC)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1E1573 is output A
Any hybrid control system DTCs in the table below are output B
Any FC control system DTCs in the table below are output C

Malfunction Content System Relevant DTC
Micro computer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C9E9F Hybrid/EV System Reset Stuck Off
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance
P0A1B04 Drive Motor "A" Control Module System Internal Failure
P1CA700 Drive Motor "A" Control Module RAM/ROM Error
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error
P1D8F04 FC Air Compressor Motor Control Module System Internal Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure
P1C731C Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
FC control system P060B49 Internal Control Module A/D Processing Performance Internal Electronic Failure
P060B71 Internal Control Module A/D Processing Performance Actuator Stuck
P060B1C Internal Control Module A/D Processing Performance Circuit Voltage Out of Range
P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06B01C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
FC control system P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
P1F651C FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range
P1F661C FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
FC control system U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
U116087 Lost Communication with FCDC Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A1B00 Drive Motor "A" Control Module Performance
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P1D8F00 FC Air Compressor Motor Control Module Performance
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
FC control system P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect
P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold
P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On
System malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P1E1500 FC Positive Contactor Actuator Stuck Closed
P1E1773 FC Negative Contactor Control Actuator Stuck Closed
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P1D9514 FC Converter Shutdown Signal Circuit Short to Ground or Open
P1D9512 FC Converter Shutdown Signal Circuit Short to Battery
P1E0A14 FC Converter Fail Signal Circuit Short to Ground or Open
P1E0A12 FC Converter Fail Signal Circuit Short to Battery
FC control system P1D0E62 Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure
P1D0619 FC Converter Phase U Current Circuit Current Above Threshold
P1DDA4B FC Converter Phase U Over Temperature
P1DDA9E FC Converter Phase U Fail Signal Stuck On
P1D0719 FC Converter Phase V Current Circuit Current Above Threshold
P1DDB4B FC Converter Phase V Over Temperature
P1DDB9E FC Converter Phase V Fail Signal Stuck On
P1D0819 FC Converter Phase W Current Circuit Current Above Threshold
P1DDC4B FC Converter Phase W Over Temperature
P1DDC9E FC Converter Phase W Fail Signal Stuck On
P1D0919 FC Converter Phase X Current Circuit Current Above Threshold
P1DDD4B FC Converter Phase X Over Temperature
P1DDD9E FC Converter Phase X Fail Signal Stuck On
P1F0117 FC Converter Output Voltage Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On


HINT:
·

P15E1573 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

2.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off and wait for 1 hours or more.


Procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > EV > Clear DTCs
50002 397
Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

3.CHECK DTC OUTPUT (FC CONTROL SYSTEM ACTIVATION)
3.CHECK DTC OUTPUT (FC CONTROL SYSTEM ACTIVATION)

Pre-procedure1

a.

None.


Procedure1

a.

Turn the ignition switch to ON (READY) and check for DTCs.

HINT:

DTC P1E1573 is output, and when the following malfunction condition is met, the ignition switch will not be able to be turned to ON (READY).


Powertrain > EV > Trouble Codes
50001 397
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
DTCs are not output (the ignition switch can be turned to ON (READY)) A
DTCs of EV control system in the tables below are output B
DTCs of FC boost control system in the tables below are output C
P1E1573 is output D
P0C7600 or P0AA073 is output E
None of the above conditions are met F


Malfunction Content System Relevant DTC
Micro computer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C9E9F Hybrid/EV System Reset Stuck Off
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1CB038 Drive Motor "A" Control Module Circuit Intermittent
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance
P0A1B04 Drive Motor "A" Control Module System Internal Failure
P1CA700 Drive Motor "A" Control Module RAM/ROM Error
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error
P1D8F04 FC Air Compressor Motor Control Module System Internal Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure
P1C731C Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
FC control system P060B49 Internal Control Module A/D Processing Performance Internal Electronic Failure
P060B71 Internal Control Module A/D Processing Performance Actuator Stuck
P060B1C Internal Control Module A/D Processing Performance Circuit Voltage Out of Range
P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06B01C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
FC control system P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
P1F651C FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range
P1F661C FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
FC control system U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
U116087 Lost Communication with FCDC Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A1B00 Drive Motor "A" Control Module Performance
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P1D8F00 FC Air Compressor Motor Control Module Performance
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
FC control system P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect
P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold
P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On
System malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P1E1500 FC Positive Contactor Actuator Stuck Closed
P1E1773 FC Negative Contactor Control Actuator Stuck Closed
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P1D9514 FC Converter Shutdown Signal Circuit Short to Ground or Open
P1D9512 FC Converter Shutdown Signal Circuit Short to Battery
P1E0A14 FC Converter Fail Signal Circuit Short to Ground or Open
P1E0A12 FC Converter Fail Signal Circuit Short to Battery
FC control system P1D0E62 Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure
P1D0619 FC Converter Phase U Current Circuit Current Above Threshold
P1DDA4B FC Converter Phase U Over Temperature
P1DDA9E FC Converter Phase U Fail Signal Stuck On
P1D0719 FC Converter Phase V Current Circuit Current Above Threshold
P1DDB4B FC Converter Phase V Over Temperature
P1DDB9E FC Converter Phase V Fail Signal Stuck On
P1D0819 FC Converter Phase W Current Circuit Current Above Threshold
P1DDC4B FC Converter Phase W Over Temperature
P1DDC9E FC Converter Phase W Fail Signal Stuck On
P1D0919 FC Converter Phase X Current Circuit Current Above Threshold
P1DDD4B FC Converter Phase X Over Temperature
P1DDD9E FC Converter Phase X Fail Signal Stuck On
P1F0117 FC Converter Output Voltage Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On


Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK DTC OUTPUT (EV, FCDC)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

D

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

E

GO TO DTC CHART (P0C7600, P0AA073)

F

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
4.CHECK DTC OUTPUT (EV, FCDC)

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 3 minutes or more.


b.

Turn the ignition switch off and wait for 10 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
DTCs are not output A
Any hybrid control system DTCs in the table below are output B
Any FC control system DTCs in the table below are output C
P1E1573, P1E1500 or P1E1773 is output D
P0C7600 or P0AA073 is output E
None of the above conditions are met F


Malfunction Content System Relevant DTC
Micro computer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C9E9F Hybrid/EV System Reset Stuck Off
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1CB038 Drive Motor "A" Control Module Circuit Intermittent
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance
P0A1B04 Drive Motor "A" Control Module System Internal Failure
P1CA700 Drive Motor "A" Control Module RAM/ROM Error
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error
P1D8F04 FC Air Compressor Motor Control Module System Internal Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure
P1C731C Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
FC control system P060B49 Internal Control Module A/D Processing Performance Internal Electronic Failure
P060B71 Internal Control Module A/D Processing Performance Actuator Stuck
P060B1C Internal Control Module A/D Processing Performance Circuit Voltage Out of Range
P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06B01C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
FC control system P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
P1F651C FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range
P1F661C FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
FC control system U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
U116087 Lost Communication with FCDC Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A1B00 Drive Motor "A" Control Module Performance
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P1D8F00 FC Air Compressor Motor Control Module Performance
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
FC control system P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect
P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold
P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On
System malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P1E1500 FC Positive Contactor Actuator Stuck Closed
P1E1773 FC Negative Contactor Control Actuator Stuck Closed
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P1D9514 FC Converter Shutdown Signal Circuit Short to Ground or Open
P1D9512 FC Converter Shutdown Signal Circuit Short to Battery
P1E0A14 FC Converter Fail Signal Circuit Short to Ground or Open
P1E0A12 FC Converter Fail Signal Circuit Short to Battery
FC control system P1D0E62 Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure
P1D0619 FC Converter Phase U Current Circuit Current Above Threshold
P1DDA4B FC Converter Phase U Over Temperature
P1DDA9E FC Converter Phase U Fail Signal Stuck On
P1D0719 FC Converter Phase V Current Circuit Current Above Threshold
P1DDB4B FC Converter Phase V Over Temperature
P1DDB9E FC Converter Phase V Fail Signal Stuck On
P1D0819 FC Converter Phase W Current Circuit Current Above Threshold
P1DDC4B FC Converter Phase W Over Temperature
P1DDC9E FC Converter Phase W Fail Signal Stuck On
P1D0919 FC Converter Phase X Current Circuit Current Above Threshold
P1DDD4B FC Converter Phase X Over Temperature
P1DDD9E FC Converter Phase X Fail Signal Stuck On
P1F0117 FC Converter Output Voltage Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On


Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

D

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

E

GO TO DTC CHART (P0C7600, P0AA073)

F

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

6.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.
A481478

Disconnect the B19 FC converter assembly connector.


d.

Disconnect the A15 and A16 EV Control ECU connector.


Procedure1

a.
A481504C03
0.573,0.896 1.083,1.281 0.51,0.385 1.438,2.156 1.948,2.542 0.51,0.385 0.833,2.146 1.344,2.531 0.51,0.385 2.292,1.906 1.729,1.01 true 1.802,4.448 1.573,3.854 true 1.156,1.875 1.552,1 true 1.833,1.896 1.563,1.083 true 1,4.448 1.26,3.865 true 0.635,4.438 1.125,3.854 true 0.75,1.021 1.208,1.219 0.458,0.198 10 false B19 1.594,2.281 2.052,2.479 0.458,0.198 10 false A16 0.229,0.146 0.688,0.344 0.458,0.198 10 false *a 0.281,2.042 0.74,2.24 0.458,0.198 10 false *b 2.292,1.917 2.75,2.115 0.458,0.198 10 false FRP 1.74,4.479 2.063,4.615 0.323,0.135 10 false FRP 1.792,1.917 2.25,2.115 0.458,0.198 10 false FRG+ 0.917,1.917 1.375,2.115 0.458,0.198 10 false FRG- 0.979,2.281 1.438,2.479 0.458,0.198 10 false A15 0.385,4.479 0.76,4.615 0.375,0.135 10 false FRG+ 0.833,4.479 1.271,4.615 0.438,0.135 10 false FRG-
*a front view of wire harness connector
(to FC Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15,B19,A16)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B19)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A15-3 (FRG+) - B19-7 (FRG+) Ignition switch off Below 1 Ω
A15-2 (FRG-) - B19-1 (FRG-) Ignition switch off Below 1 Ω
A16-6 (FRP) - B19-3 (FRP) Ignition switch off Below 1 Ω
A15-3 (FRG+) or B19-7 (FRG+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A15-2 (FRG-) or B19-1 (FRG-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-6 (FRP) or B19-3 (FRP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A15 and A16 EV Control ECU connector.


b.

Reconnect the B19 FC converter assembly connector.


c.

Install the electric heater sub-assembly.



OK

8.CHECK FC STACK MAIN RELAY, FC PRECHARGE JUNCTION ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK FC STACK MAIN RELAY, FC PRECHARGE JUNCTION ASSEMBLY

Pre-procedure1

a.

Disconnect the A15 and A16 EV Control ECU connector.


Procedure1

a.
A491112C03
1.479,0.573 1.958,0.938 0.479,0.365 0.906,0.573 1.385,0.938 0.479,0.365 1.552,3.01 1.583,2.302 true 2.271,3.021 1.792,2.302 true 1.948,3 1.646,2.302 true 0.813,3.01 1.146,2.302 true 1.177,3 1.271,2.302 true 1.615,0.698 2.073,0.896 0.458,0.198 10 false A16 2.271,3.031 2.729,3.229 0.458,0.198 10 false FRB+ 1.885,3.042 2.344,3.24 0.458,0.198 10 false FRB- 0.094,0.135 0.552,0.333 0.458,0.198 10 false *a 1.063,0.688 1.521,0.885 0.458,0.198 10 false A15 1.49,3.042 1.948,3.24 0.458,0.198 10 false FRP 1.042,3.042 1.5,3.24 0.458,0.198 10 false FRG- 0.594,3.042 1.052,3.24 0.458,0.198 10 false FRG+
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A15)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-3(FRB+) - A16-5(FRB-) Ignition switch off 11.07 to 13.53 Ω
A15-3(FRG+) - A15-2(FRG-) Ignition switch off 11.07 to 13.53 Ω
A16-6(FRP) - Body ground Ignition switch off 112 to 274 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A15 and A16 EV Control ECU connector.



OK

9.REMOVE FC CONVERTER ASSEMBLY

NG

10.REMOVE FC CONVERTER ASSEMBLY
9.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE FC CONVERTER ASSEMBLY COMPONENT PARTS

Replace the FC converter assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY

·

FC stack main relay (FRB)

·

FC stack main relay (FRB)

·

FC precharge junction assembly (FRP)

·

FC converter power module transistor


HINT:
·

Refer to the parts location for the FC converter assembly components.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter assembly components.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>SYSTEM DESCRIPTION




10.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE FC CONVERTER ASSEMBLY COMPONENT PARTS

Replace the FC converter assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY

·

FC stack main relay (FRB)

·

FC stack main relay (FRG)

·

FC precharge junction assembly (FRP)

·

No. 1 FC converter wire

·

No. 2 FC converter wire

·

FCDC converter control ECU board sub-assembly

·

FC converter power module transistor


HINT:
·

Refer to the parts location for the FC converter assembly components.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter assembly components.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>SYSTEM DESCRIPTION