MALFUNCTION DESCRIPTION
The EV control ECU detects that a FC safety device (FC interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)
The cause of this malfunction may be one of the following:
FC converter power outlet cable malfunction
FC converter assembly malfunction
EV control ECU malfunction
FCDC converter control ECU malfunction
FC converter assembly malfunction
Wire harness malfunction
Connector malfunction
When the EV control ECU detects that a FC safety device (FC interlock) is operated, such as when the FC converter outlet cable is removed, it will prohibit the system operation or shut off the system main relay.
The safety device is installed to the FC converter outlet cable connector of the FC converter assembly.
If the FCDC converter control ECU board sub-assembly, No. 1 FC converter wire is removed, the interlock signal line will be open.
If the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. When the safety devices are re-installed correctly, the system will return to normal when the ignition switch is turned ON again.
When an open circuit is detected, the system main relays will be shut off when the next drive cycle starts, until the system returns to normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1E1A13 | FC Interlock Switch Circuit Open | With the vehicle stopped, the FC interlock signal line became open.
(1 trip detection logic) |
·
FCDC converter control ECU board sub-assembly ·
EV control ECU ·
FC converter power outlet terminal sub-assembly ·
FC converter power outlet cable (inverter with converter assembly) ·
No. 1 FC converter wire |
Master Warning:
Comes on |
EV | A |
| P1E1A92 | FC Interlock Switch Performance or Incorrect Operation | FC interlock signal line opens while the vehicle is being driven (at 5 km/h (3 mph) or more).
(1 trip detection logic) |
·
FCDC converter control ECU board sub-assembly ·
EV control ECU ·
FC converter power outlet terminal sub-assembly ·
FC converter power outlet cable (inverter with converter assembly) ·
No. 1 FC converter wire |
Master Warning:
Comes on |
EV | A |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Turn the ignition switch to ON and wait for 5 seconds or more.
Enter the following menus: Powertrain / EV / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.
Make sure to remove the service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.
The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.
Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.
| *a | Without waiting for 10 minutes |
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.
If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.
Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.
Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL
Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.
After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P1E1A13 or P1E1A92 is output | A |
| P1E1A13 or P1E1A92 is output and any DTCs in the table below are output | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | |
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | |
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | |
| P060B49 | Drive Motor "A" Control Module Internal Electronic Failure | |
| P060B71 | Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck | |
| P060B1C | Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range | |
| P1CE349 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure | |
| P1CE371 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck | |
| P1CE31C | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range | |
| P060A45 | Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure | |
| P060A44 | Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure | |
| P060A29 | Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid | |
| P060A49 | Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure | |
| Power source circuit malfunction | P06881F | ECM/PCM Power Relay Sense Circuit Intermittent |
| System malfunction | P1C9E9F | Hybrid/EV System Reset Stuck Off |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1E1A13 or P1E1A92 is output | A |
| P1E1A13 or P1E1A92 is not output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Procedure1
| *1 | FC Converter Power Outlet Cable (Inverter with Converter Assembly) |
| *a | Interlock Connector |
Check the condition of the FC converter power outlet cable interlock.
Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the electric heater sub-assembly.
Disconnect the B19 FC converter connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Front view of wire harness connector
(to FC Converter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B19)Location & Routingewd_type=routing;type=c;code=B19 Click Connector(B19)Engine Compartment>No. 2 Stack Wire>FC Converter Assemblyewd_type=component;type=c;code=B19;pinno=10 |
||
| B19-10 (ILKI) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the B19 FC converter connector.
Install the electric heater sub-assembly.
OK
NG
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Remove the No. 1 FC converter wire from the FCDC converter control ECU board sub-assembly.
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY
Remove the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY
Procedure1
| *a | Component without harness connected
(No. 1 FC Converter Wire) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (ILKCO) - B-2 (ILKCO) | Ignition switch off | Below 1 Ω |
| A-11 (ILKCI) - B- 1 (ILKCI) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.
Reconnect the No. 1 FC converter wire from the FCDC converter control ECU board sub-assembly.
OK
NG
Pre-procedure1
Remove the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY
Remove the FC converter power outlet terminal sub-assembly from the FC converter assembly.
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY
Procedure1
| *a | Component without harness connected
(FC Converter Power Outlet Terminal Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (ILKCI) - C-2 (ILKCI) | Ignition switch off | Below 1 Ω |
| B-2 (ILKCO) - C-1 (ILKCO) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the FC converter power outlet terminal sub-assembly from the FC converter assembly.
Reconnect the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.
OK
NG
Pre-procedure1
Turn the ignition switch to ON.
Remove the electric heater sub-assembly.
Disconnect the B19 FC converter connector.
Procedure1
| *a | Component with harness connected
(EV Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A15)Location & Routingewd_type=routing;type=c;code=A15 Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A15;pinno=7 |
||
| A15-7 (SILK) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Reconnect the B19 FC converter connector.
Install the electric heater sub-assembly.
OK
NG
Check the connections of each connector.
Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.
| Proceed to |
|---|
| OK |
| NG |
OK
NG