Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0455415 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly and EV control ECU detects the rear seat belt state and rear seat occupant state. The rear seat belt warning light illuminates, blinks or turns off in accordance with the vehicle speed, rear seat belt state and rear seat occupant state.

WIRING DIAGRAM

w/ Occupant Classification System


B620507E01
5.865,4.958 6.323,5.156 0.458,0.198 10 false D41 5.854,5.135 7.104,5.552 1.25,0.417 10 false Combination Meter Assembly 3,4.656 5.479,5.073 2.479,0.417 10 false Rear Seat Cushion Pad Sub-assembly 0.625,4.208 2.646,4.625 2.021,0.417 10 false Rear Seat Inner with Center Belt Assembly RH 0.531,2.573 3.01,2.99 2.479,0.417 10 false Rear Seat Inner Belt Assembly LH 3.385,0.854 4.979,1.344 1.594,0.49 10 false Rear Occupant Detection Sensor (for LH) 3.385,2.208 4.979,2.698 1.594,0.49 10 false Rear Occupant Detection Sensor (for Center) 3.344,4.104 4.938,4.594 1.594,0.49 10 false Rear Occupant Detection Sensor (for RH) 5.25,0.625 6.531,1.031 1.281,0.406 10 false M7 2.823,0.625 4.844,1.042 2.021,0.417 10 false M7 2.802,1.979 4.823,2.396 2.021,0.417 10 false M8 5.24,1.99 6.823,2.427 1.583,0.438 10 false M8 2.813,3.885 4.833,4.302 2.021,0.417 10 false M9 5.24,3.896 6.802,4.344 1.563,0.448 10 false M9 2.25,0.615 4.271,1.031 2.021,0.417 10 false G78 0.583,0.604 2.604,1.021 2.021,0.417 10 false G78 2.26,1.979 4.281,2.396 2.021,0.417 10 false G75 0.604,1.979 2.625,2.396 2.021,0.417 10 false G75 0.594,3.885 2.615,4.302 2.021,0.417 10 false G77 2.25,3.885 4.271,4.302 2.021,0.417 10 false G77 2.344,3.698 4.365,4.115 2.021,0.417 10 false 1 2.344,1.792 4.365,2.208 2.021,0.417 10 false 1 2.344,0.417 4.365,0.833 2.021,0.417 10 false 1 0.677,0.406 2.698,0.823 2.021,0.417 10 false 2 0.677,1.76 2.698,2.177 2.021,0.417 10 false 2 0.688,3.677 2.708,4.094 2.021,0.417 10 false 2 1.792,3.781 3.813,4.198 2.021,0.417 10 false RBR+ 0.958,3.771 2.979,4.188 2.021,0.417 10 false RBR- 0.948,1.875 2.969,2.292 2.021,0.417 10 false CBR- 1.802,1.865 3.823,2.281 2.021,0.417 10 false CBR+ 1.802,0.469 3.823,0.885 2.021,0.417 10 false LBR+ 0.948,0.469 2.969,0.885 2.021,0.417 10 false LBR- 5.302,0.417 6.635,0.844 1.333,0.427 10 false 2 5.302,1.781 6.635,2.208 1.333,0.427 10 false 2 5.313,3.688 6.646,4.115 1.333,0.427 10 false 2 2.865,3.688 4.885,4.104 2.021,0.417 10 false 1 2.865,1.802 4.885,2.219 2.021,0.417 10 false 1 2.875,0.427 4.896,0.844 2.021,0.417 10 false 1 5.938,1.99 7.115,2.458 1.177,0.469 10 false RCSB 5.948,0.594 7.125,1.063 1.177,0.469 10 false RLSB 5.958,3.906 7.135,4.375 1.177,0.469 10 false RRSB 5.698,0.531 6.875,1 1.177,0.469 10 false 14 5.688,1.885 6.865,2.354 1.177,0.469 10 false 13 5.677,3.802 6.854,4.271 1.177,0.469 10 false 12


w/o Occupant Classification System


B608308E03
4.896,8.115 7.042,8.313 2.146,0.198 10 false EV Control ECU 4.906,7.927 6.188,8.135 1.281,0.208 10 false A16 4.906,7.271 5.521,7.469 0.615,0.198 10 false BRFC 4.906,5.208 5.521,5.406 0.615,0.198 10 false BLFC 4.906,6.229 5.521,6.427 0.615,0.198 10 false BCFC 4.615,5.094 4.927,5.292 0.313,0.198 10 false 18 4.604,6.083 4.896,6.375 0.292,0.292 10 false 28 4.698,7.146 5.01,7.427 0.313,0.281 10 false 8 0.813,8.333 4.479,8.531 3.667,0.198 10 false : CAN Communication Line 2.323,7.594 2.781,7.792 0.458,0.198 10 false G77 2.146,5.229 2.604,5.427 0.458,0.198 10 false G78 2.167,6.229 2.625,6.427 0.458,0.198 10 false G75 3.833,5.219 4.292,5.417 0.458,0.198 10 false G78 3.823,6.229 4.281,6.427 0.458,0.198 10 false G75 2.104,6.552 7,6.75 4.896,0.198 10 false Rear Seat Inner Belt Assembly LH 2.333,7.75 4,8.583 1.667,0.833 10 false Rear Seat Inner with Center Belt Assembly RH 2.521,7.167 3.135,7.365 0.615,0.198 10 false RBR+ 3.365,7.156 3.979,7.354 0.615,0.198 10 false RBR- 2.5,6.125 3.115,6.323 0.615,0.198 10 false CBR+ 3.406,6.125 4.021,6.323 0.615,0.198 10 false CBR- 2.5,5.083 3.115,5.281 0.615,0.198 10 false LBR+ 3.417,5.083 4.031,5.281 0.615,0.198 10 false LBR- 2.344,7.156 2.646,7.438 0.302,0.281 10 false 1 2.26,5 2.417,5.198 0.156,0.198 10 false 1 2.25,6 2.406,6.198 0.156,0.198 10 false 1 3.917,6.021 4.219,6.302 0.302,0.281 10 false 2 3.917,5 4.219,5.281 0.302,0.281 10 false 2 3.823,7.167 4.125,7.448 0.302,0.281 10 false 2 1.188,4.135 6.385,4.333 5.198,0.198 10 false Rear Seat Cushion Pad Sub-assembly 1.427,3.604 2.969,4.26 1.542,0.656 10 false Rear Occupant Detection Sensor (for LH) 1.427,3.448 1.74,3.646 0.313,0.198 10 false M7 1.469,3.094 1.625,3.292 0.156,0.198 10 false 1 1.479,1.844 1.635,2.042 0.156,0.198 10 false 1 1.49,0.583 1.646,0.781 0.156,0.198 10 false 1 2.969,0.594 3.125,0.792 0.156,0.198 10 false 2 2.948,1.854 3.104,2.052 0.156,0.198 10 false 2 2.969,3.115 3.125,3.313 0.156,0.198 10 false 2 1.438,2.229 1.75,2.427 0.313,0.198 10 false M8 1.417,2.427 2.99,3.344 1.573,0.917 10 false Rear Occupant Detection Sensor (for Center) 1.396,0.917 1.708,1.115 0.313,0.198 10 false M9 1.406,1.125 2.958,1.885 1.552,0.76 10 false Rear Occupant Detection Sensor (for RH) 4.906,3.219 5.521,3.417 0.615,0.198 10 false RLSB 4.938,2.01 5.552,2.208 0.615,0.198 10 false RCSB 4.906,0.698 5.521,0.896 0.615,0.198 10 false RRSB 4.583,0.563 4.896,0.76 0.313,0.198 10 false 12 4.583,1.875 4.896,2.073 0.313,0.198 10 false 13 4.594,3.115 4.906,3.313 0.313,0.198 10 false 14 4.646,3.823 6.479,4.417 1.833,0.594 10 false Combination Meter Assembly 4.667,3.656 5.125,3.854 0.458,0.198 10 false D41 1.052,5.417 2.583,5.615 1.531,0.198 10 false IGCT NO. 5 0.146,5.26 0.896,6.094 0.75,0.833 10 false from IGCT NO. 2 Relay


CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:

Inspect the fuses and relays related to this system before inspecting the suspected areas below.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/o Occupant Classification System A
w/ Occupant Classification System B



A

2.READ VALUE USING GTS

B

15.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > EV > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Right Seat Buckle Switch Status Rear seat inner belt RH buckle signal Buckle or Unbuckle Buckle: Rear RH seat belt fastened
Unbuckle: Rear RH seat belt not fastened
-
Rear Left Seat Buckle Switch Status Rear seat inner belt LH buckle signal Buckle or Unbuckle Buckle: Rear LH seat belt fastened
Unbuckle: Rear LH seat belt not fastened
-
Rear Center Seat Buckle Switch Status Rear seat inner center belt buckle signal Buckle or Unbuckle Buckle: Rear center seat belt fastened
Unbuckle: Rear center seat belt not fastened
-
Powertrain > EV > Data List
Tester Display
Rear Right Seat Buckle Switch Status
Rear Left Seat Buckle Switch Status
Rear Center Seat Buckle Switch Status
50003 397 1045,1046,1047
OK:

The GTS display changes correctly in response to the rear seat belt buckle switch condition.



Result:
Result Proceed to
OK A
NG (Rear RH seat belt malfunction) B
NG (Rear center seat belt malfunction) C
NG (Rear LH seat belt malfunction) D



A

3.READ VALUE USING GTS

B

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

C

9.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

D

12.INSPECT REAR SEAT INNER BELT ASSEMBLY LH
3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Right Seat Buckle / Occupant Detection Warning Switch Rear occupant detection sensor RH signal ON or OFF ON: Rear RH seat occupied
OFF: Rear RH seat not occupied
-
Rear Left Seat Buckle / Occupant Detection Warning Switch Rear occupant detection sensor LH signal ON or OFF ON: Rear LH seat occupied
OFF: Rear LH seat not occupied
-
Rear Center Seat Buckle / Occupant Detection Warning Switch Rear occupant detection sensor with center signal ON or OFF ON: Rear center seat occupied
OFF: Rear center seat not occupied
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Right Seat Buckle / Occupant Detection Warning Switch
Rear Left Seat Buckle / Occupant Detection Warning Switch
Rear Center Seat Buckle / Occupant Detection Warning Switch
50003 409 30,31,32
OK:

The GTS display changes correctly in response to the rear seat condition (occupied or unoccupied).



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)
4.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

OK

5.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the M7 rear occupant detection sensor (for LH) connector.


b.

Disconnect the M9 rear occupant detection sensor (for RH) connector.


c.

Disconnect the M8 rear occupant detection sensor (for center) connector.


d.

Disconnect the D41 combination meter assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition

Click Location & Routing(M7,D41)Location & Routing

Click Connector(M7)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor LH (Separate Type Front Seat Cushion Pad)

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

M7-2 - D41-14 (RLSB) Always Below 1 Ω
M7-1 - Body ground Always Below 1 Ω
M7-2 or D41-14 (RLSB) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition

Click Location & Routing(M9,D41)Location & Routing

Click Connector(M9)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor RH (Separate Type Front Seat Cushion Pad)

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

M9-2 - D41-12 (RRSB) Always Below 1 Ω
M9-1 - Body ground Always Below 1 Ω
M9-2 or D41-12 (RRSB) - Body ground Always 10 kΩ or higher

for Center
Tester Connection Condition Specified Condition

Click Location & Routing(M8,D41)Location & Routing

Click Connector(M8)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor Center (Separate Type Front Seat Cushion Pad)

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

M8-2 - D41-13 (RCSB) Always Below 1 Ω
M8-1 - Body ground Always Below 1 Ω
M8-2 or D41-13 (RCSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

OK

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - POWER SUPPLY)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - POWER SUPPLY)
a.

Disconnect the rear seat inner with center belt assembly RH connector.


b.
B608320C01
1.417,0.25 1.917,0.583 0.5,0.333 2.042,1.313 2.417,0.5 2.417,0.5 2.583,0.5 true 1.542,0.333 2,0.531 0.458,0.198 10 false G77 2.656,0.417 3.271,0.615 0.615,0.198 10 false RBR+ 0.125,0.167 0.5,0.406 0.375,0.24 12 false *a
*a Front view of wire harness connector
(to Rear Seat Inner with Center Belt Assembly RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G77)Location & Routing

Click Connector(G77)Seat>Floor Wire>Rear Seat Inner Belt with Center Assembly RH

G77-1 (RBR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - EV CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - EV CONTROL ECU)
a.

Disconnect the G77 rear seat inner with center belt assembly RH connector.


b.

Disconnect the A16 EV control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G77,A16)Location & Routing

Click Connector(G77)Seat>Floor Wire>Rear Seat Inner Belt with Center Assembly RH

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G77-2 (RBR-) - A16-8 (BRFC) Always Below 1 Ω
G77-2 (RBR-) or A16-8 (BRFC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

OK

10.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - POWER SUPPLY)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY LH

10.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - POWER SUPPLY)
a.

Disconnect the rear inner seat belt assembly LH connector.


b.
B608321C04
1.542,0.323 1.958,0.635 0.417,0.313 2.052,1.417 2.5,0.5 2.5,0.5 2.667,0.5 true 0.167,0.167 0.542,0.406 0.375,0.24 12 false *a 2.74,0.417 3.354,0.615 0.615,0.198 10 false CBR+ 1.615,0.375 2.073,0.573 0.458,0.198 10 false G75
*a Front view of wire harness connector
(to Rear Seat Inner Belt Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G75)Location & Routing

Click Connector(G75)Seat>Floor Wire>Rear Seat Inner Belt Assembly LH

G75-1 (CBR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - EV CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - EV CONTROL ECU)
a.

Disconnect the G75 rear inner seat belt assembly LH connector.


b.

Disconnect the A16 EV control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G75,A16)Location & Routing

Click Connector(G75)Seat>Floor Wire>Rear Seat Inner Belt Assembly LH

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G75-2 (CBR-) - A16-28 (BCFC) Always Below 1 Ω
G75-2 (CBR-) or A16-28 (BCFC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

OK

13.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - POWER SUPPLY)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY LH

13.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - POWER SUPPLY)
a.

Disconnect the rear inner seat belt assembly LH connector.


b.
B608320C02
1.417,0.25 1.917,0.583 0.5,0.333 2.042,1.313 2.417,0.5 2.417,0.5 2.583,0.5 true 1.542,0.333 2,0.531 0.458,0.198 10 false G78 2.656,0.417 3.271,0.615 0.615,0.198 10 false LBR+ 0.125,0.167 0.5,0.406 0.375,0.24 12 false *a
*a Front view of wire harness connector
(to Rear Seat Inner Belt Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G78)Location & Routing

Click Connector(G78)Seat>Floor Wire>Rear Seat Inner Belt Assembly LH

G78-1 (LBR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - EV CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - EV CONTROL ECU)
a.

Disconnect the G78 rear inner seat belt assembly LH connector.


b.

Disconnect the A16 EV control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G78,A16)Location & Routing

Click Connector(G78)Seat>Floor Wire>Rear Seat Inner Belt Assembly LH

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G78-2 (LBR-) - A16-18 (BLFC) Always Below 1 Ω
G78-2 (LBR-) or A16-18 (BLFC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Right Seat Buckle / Occupant Detection Warning Switch Rear occupant detection sensor RH signal ON or OFF ON: Rear RH seat belt fastened and occupied
OFF: Rear RH seat belt not fastened and occupied
-
Rear Left Seat Buckle / Occupant Detection Warning Switch Rear occupant detection sensor LH signal ON or OFF ON: Rear LH seat belt fastened and occupied
OFF: Rear LH seat belt not fastened and occupied
-
Rear Center Seat Buckle / Occupant Detection Warning Switch Rear occupant detection sensor with center signal ON or OFF ON: Rear center seat belt fastened and occupied
OFF: Rear center seat belt not fastened and occupied
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Right Seat Buckle / Occupant Detection Warning Switch
Rear Left Seat Buckle / Occupant Detection Warning Switch
Rear Center Seat Buckle / Occupant Detection Warning Switch
50003 409 30,31,32
OK:

The GTS display changes correctly in response to the rear seat condition (occupied or unoccupied).


Result:
Result Proceed to
OK A
NG (Rear RH seat belt malfunction) B
NG (Rear center seat belt malfunction) C
NG (Rear LH seat belt malfunction) D




A

REPLACE COMBINATION METER ASSEMBLY

B

16.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

C

20.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

D

24.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)
16.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

OK

17.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

17.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the M9 rear occupant detection sensor (for RH) connector.


b.

Disconnect the D41 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M9,D41)Location & Routing

Click Connector(M9)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor RH (Separate Type Front Seat Cushion Pad)

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

M9-2 - D41-12 (RRSB) Always Below 1 Ω
M9-2 or D41-12 (RRSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

OK

19.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - REAR OCCUPANT DETECTION SENSOR AND BODY GROUND)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

19.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH - REAR OCCUPANT DETECTION SENSOR AND BODY GROUND)
a.

Disconnect the M9 rear occupant detection sensor (for RH) connector.


b.

Disconnect the G77 rear seat inner with center belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M9,G77)Location & Routing

Click Connector(M9)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor RH (Separate Type Front Seat Cushion Pad)

Click Connector(G77)Seat>Floor Wire>Rear Seat Inner Belt with Center Assembly RH

M9-1 - G77-1 (RBR+) Always Below 1 Ω
G77-2 (RBR-) - Body ground Always Below 1 Ω
M9-1 or G77-1 (RBR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

OK

21.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

21.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the M8 rear occupant detection sensor (for center) connector.


b.

Disconnect the D41 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M8,D41)Location & Routing

Click Connector(M8)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor Center (Separate Type Front Seat Cushion Pad)

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

M8-2 - D41-13 (RCSB) Always Below 1 Ω
M8-2 or D41-13 (RCSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

OK

23.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - REAR OCCUPANT DETECTION SENSOR AND BODY GROUND)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY LH

23.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - REAR OCCUPANT DETECTION SENSOR AND BODY GROUND)
a.

Disconnect the M8 rear occupant detection sensor (for center) connector.


b.

Disconnect the G75 rear seat inner belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M8,G75)Location & Routing

Click Connector(M8)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor Center (Separate Type Front Seat Cushion Pad)

Click Connector(G75)Seat>Floor Wire>Rear Seat Inner Belt Assembly LH

M8-1 - G75-1 (CBR+) Always Below 1 Ω
G75-2 (CBR-) - Body ground Always Below 1 Ω
M8-1 or G75-1 (CBR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.INSPECT REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

OK

25.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

25.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the M7 rear occupant detection sensor (for LH) connector.


b.

Disconnect the D41 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M7,D41)Location & Routing

Click Connector(M7)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor LH (Separate Type Front Seat Cushion Pad)

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

M7-2 - D41-14 (RLSB) Always Below 1 Ω
M7-2 or D41-14 (RLSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.INSPECT REAR SEAT INNER BELT ASSEMBLY LH

OK

27.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - REAR OCCUPANT DETECTION SENSOR AND BODY GROUND)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY LH

27.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY LH - REAR OCCUPANT DETECTION SENSOR AND BODY GROUND)
a.

Disconnect the M7 rear occupant detection sensor (for LH) connector.


b.

Disconnect the G78 rear seat inner belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M7,G78)Location & Routing

Click Connector(M7)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Belt Warning Occupant Detection Sensor LH (Separate Type Front Seat Cushion Pad)

Click Connector(G78)Seat>Floor Wire>Rear Seat Inner Belt Assembly LH

M7-1 - G78-1 (LBR+) Always Below 1 Ω
G78-2 (LBR-) - Body ground Always Below 1 Ω
M7-1 or G78-1 (LBR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR