Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C8449  High Voltage Power Resource Circuit Short during Ready ON  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU monitors the high-voltage wiring between the EV supply battery assembly and inverter with converter assembly and detects an open circuit malfunction.

HINT:
·

This DTC is differentiated from P300449 based on detection timing (P1C8449 is detected after ignition switch is turned to ON (READY)). If P300449 is also output at the same time, first perform troubleshooting for P300449.

·

If there is a SMRG stuck open malfunction, only P1C8449 is output.



The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH or VL) internal circuit malfunction
·

Voltage sensor (VH or VL) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

EV supply battery assembly malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction

·

FC converter assembly malfunction


Low-voltage circuit (12 V) malfunction
·

EV control ECU malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1C8449 High Voltage Power Resource Circuit Short during Ready ON High-voltage circuit malfunctions between the EV supply battery assembly and inverter with converter assembly.
When the ignition switch is ON (READY), both "VL-Voltage before Boosting" and "VH-Voltage after Boosting" drop abnormally.
The EV fuse is blown, the service plug grip is removed, SMRB or SMRG remains open, or the high-voltage cable has an open circuit.
(1 trip detection logic)
·

No. 1 EV battery junction block assembly

·

Wire harness or connector

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1C8449
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



The following items can be helpful when performing repairs:

Data List
·

Ready Signal


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.


4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip and FC converter power outlet cable.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1C8449 only is output, or P0A9563 and DTCs except the ones in the table below are also output A
Any hybrid control system DTCs in the table below are output B
Any hybrid battery system DTCs in the table below are output C
P0A9563 is also output D


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
Hybrid battery system P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0E311C Boosting Converter Voltage Sensor "A" Voltage Out of Range
P300449 High Voltage Power Resource Circuit Short during Pre-Charge
P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
P0CA300 DC/DC Converter Step Up Voltage Performance
Hybrid battery system P300016 Hybrid/EV Battery Control System Circuit Voltage Below Threshold


HINT:
·

P1C8449 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

D

2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (EV)
3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).

HINT:
·

If the ignition switch could not be turned to ON (READY), turn the ignition switch off and check for DTCs after turning the ignition switch to ON (READY) again.

·

Because P300449 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.




b.

Ensure the safety of the areas in front and at the back of the vehicle.


c.

Depress the accelerator pedal in park (P).


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1C8449 is output B
Ignition switch could not be turned to ON (READY) and DTC P300449 is output C



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

4.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

C

4.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014

Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

OK (for RHD)

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

7.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478500E03
2.01,0.375 2.365,0.677 0.354,0.302 2.094,0.458 2.333,0.604 0.24,0.146 10 true z24

Disconnect the z24 No. 1 EV battery junction block assembly connector.


d.

Disconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A479459C25
2.552,3.5 3.01,3.865 0.458,0.365 0.833,1.51 1.292,1.865 0.458,0.354 0.833,1.938 1.292,2.292 0.458,0.354 1.042,4.24 1.375,3.823 true 0.656,2.365 0.594,1.75 true 0.375,2.385 0.458,1.74 true 2.406,4.24 2.115,3.823 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.198,2.76 0.51,2.958 0.313,0.198 10 false *b 2.688,3.615 3,3.813 0.313,0.198 10 false z24 0.823,4.302 1.333,4.49 0.51,0.188 10 false SMRB 0.938,1.604 1.396,1.802 0.458,0.198 10 false G14 0.021,2.417 0.479,2.583 0.458,0.167 10 false SMRB 0.615,2.406 1.073,2.573 0.458,0.167 10 false SMRG 2.344,4.292 2.896,4.49 0.552,0.198 10 false SMRG 1.354,1.604 1.813,1.802 0.458,0.198 10 false *A 0.948,2.042 1.406,2.24 0.458,0.198 10 false A14 1.385,2.021 1.844,2.219 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU )
*b Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,z24)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

G14-4 (SMRB) - z24-1 (SMRB) Ignition switch off Below 1 Ω
G14-2 (SMRG) - z24-4 (SMRG) Ignition switch off Below 1 Ω


for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,z24)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

A14-4 (SMRB) - z24-1 (SMRB) Ignition switch off Below 1 Ω
A14-2 (SMRG) - z24-4 (SMRG) Ignition switch off Below 1 Ω

Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


b.

Reconnect the z24 No. 1 EV battery junction block assembly connector.


c.

Install the No. 10 EV battery shield panel.



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

OK

10.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

11.CLEAR DTC
11.CLEAR DTC

NEXT

12.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)
12.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)

Pre-procedure1

a.

Install the service plug grip.


b.

Turn the ignition switch to ON (READY).


Procedure1

a.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > EV > Data List
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50003 397 150,227
Result:
Result Proceed to
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
None of the adove conditions are met. B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B