Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1CAD49  Drive Motor "A" Position Sensor Internal Electronic Failure  P1CB038  Drive Motor "A" Position Sensor REF Signal Frequency Incorrect  P1CB300  Drive Motor "A" Position Sensor REF Signal Oscillation Stop  


DESCRIPTION

The MG ECU, which is built into the inverter with converter assembly, monitors its internal operation and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure Motor resolver angle error
The difference between the resolver angle for control and estimated resolver angle exceeds the allowable limit.
(1 trip detection logic)
·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

FC air compressor with motor assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect Resolver REF signal cycle error
Excitation signal (REF signal) for resolver angle detection cycle error
(1 trip detection logic)
·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

FC air compressor with motor assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop Resolver REF signal oscillation stop error
An error is detected when the excitation signal (REF signal) for resolver angle detection is not detected.
(1 trip detection logic)
·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

FC air compressor with motor assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1CAD49 Motor Revolution
P1CB038
P1CB300

WIRING DIAGRAM

Refer to the wiring diagram for DTC P1E8649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


·

If DTC P1CAD49 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the ignition switch to ON (READY).

(b)

Drive the vehicle at 5 km/h (3 mph) or more for 5 seconds or more.

(c)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(d)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




·

If DTC P1CB038 or P1CB300 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the ignition switch to ON and wait for 5 seconds or more.

(b)

Enter the following menus: Powertrain / EV / Utility / All Readiness.

(c)

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




·

When a resolver signal error exists, the vehicle may not drive smoothly.


CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1CAD49, P1CB038 or P1CB300 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Relevant DTC
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)

OK

4.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

16.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)
5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

6.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MOTOR RESOLVER

OK

7.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

NG

13.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)
7.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

9.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

10.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

11.CHECK INTERMITTENT PROBLEMS

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK INTERMITTENT PROBLEMS
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


a.

Check the wire harness and connectors between the inverter with converter and motor resolver for water intrusion and defective connector connections, and check the terminal contact pressure.


Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT (SIMULATION TEST)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

12.CHECK DTC OUTPUT (SIMULATION TEST)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 5 seconds or more.


b.

Turn the ignition switch to ON (READY)


c.

Drive the vehicle at 5 km/h (3 mph) or more for 5 seconds or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1CAD49, P1CB038 or P1CB300 is output A
DTCs are not output B


HINT:

A DTC is not output if the system was returned to normal by checking the connector connection or cleaning the connector.



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

END

13.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

14.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

15.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

16.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

17.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

18.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY