Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1E8649  FC Air Compressor Motor Position Sensor Internal Electronic Failure  P1E8738  FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect  P1E8800  FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop  


DESCRIPTION

The MG ECU, which is built into the inverter with converter assembly, monitors its internal operation and detects the following malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure FC air compressor motor resolver angle error
The difference between the resolver angle for control and estimated resolver angle exceeds the allowable limit.
(1 trip detection logic)
·

Inverter with converter assembly

·

FC air compressor motor assembly

·

FCV with motor transaxle assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect FC air compressor motor resolver REF signal cycle error
Excitation signal (REF signal) for resolver angle detection cycle error
(1 trip detection logic)
·

Inverter with converter assembly

·

FC air compressor with motor assembly

·

FCV with motor transaxle assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop FC air compressor motor resolver REF signal oscillation stop error
An error is detected when the excitation signal (REF signal) for resolver angle detection is not detected.
(1 trip detection logic)
·

Inverter with converter assembly

·

FC air compressor with motor assembly

·

FCV with motor transaxle assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P1E8649 FC Air Compressor Motor Speed
P1E8738
P1E8800

WIRING DIAGRAM

for LHD:
A480857E01
6.24,0.625 6.865,1.021 0.625,0.396 10 false Oscillation Circuit 0.635,0.25 1.583,0.469 0.948,0.219 10 false Excitation Coil 0.688,3.344 1.635,3.635 0.948,0.292 10 false Excitation Coil 1.76,0.417 2.104,0.635 0.344,0.219 10 false MRF 1.656,2.042 2.125,2.26 0.469,0.219 10 false MCSG 1.75,1.073 2.094,1.292 0.344,0.219 10 false MSN 1.656,1.385 2.156,1.625 0.5,0.24 10 false MSNG 1.75,1.729 2.094,1.948 0.344,0.219 10 false MCS 1.667,0.74 2.094,0.958 0.427,0.219 10 false MRFG 2.177,0.385 2.406,0.604 0.229,0.219 10 false 6 2.146,2.052 2.375,2.271 0.229,0.219 10 false 11 2.156,1.063 2.385,1.281 0.229,0.219 10 false 10 2.146,1.396 2.375,1.615 0.229,0.219 10 false 13 2.177,1.729 2.406,1.948 0.229,0.219 10 false 8 2.167,0.74 2.396,0.958 0.229,0.219 10 false 1 0.292,2.365 0.885,2.573 0.594,0.208 10 false G154 0.281,2.531 1.365,2.75 1.083,0.219 10 false Motor Resolver 1.76,3.531 2.104,3.75 0.344,0.219 10 false GRF 1.656,5.156 2.083,5.375 0.427,0.219 10 false GCSG 1.75,4.188 2.094,4.406 0.344,0.219 10 false GSN 1.656,4.51 2.083,4.729 0.427,0.219 10 false GSNG 1.74,4.833 2.083,5 0.344,0.167 10 false GCS 1.656,3.854 2.083,4.073 0.427,0.219 10 false GRFG 0.219,5.49 0.552,5.656 0.333,0.167 10 false B24 0.208,5.656 2.656,5.896 2.448,0.24 10 false FC Air Compressor Motor Resolver 2.135,3.531 2.469,3.75 0.333,0.219 10 false 1 2.156,5.177 2.385,5.396 0.229,0.219 10 false 7 2.146,4.198 2.375,4.417 0.229,0.219 10 false 2 2.146,4.521 2.375,4.74 0.229,0.219 10 false 6 2.156,4.854 2.385,5.073 0.229,0.219 10 false 3 2.156,3.854 2.385,4.073 0.229,0.219 10 false 5 0.115,6.083 2.781,6.365 2.667,0.281 10 false FC Air Compressor with Motor Assembly 5.646,0.396 5.99,0.615 0.344,0.219 10 false MRF 5.635,0.698 6.063,0.917 0.427,0.219 10 false MRFG 5.635,1.156 5.979,1.375 0.344,0.219 10 false MSN 5.635,1.49 6.115,1.698 0.479,0.208 10 false MSNG 5.635,1.813 5.979,2.031 0.344,0.219 10 false MCS 5.635,2.125 6.125,2.354 0.49,0.229 10 false MCSG 5.646,2.396 6.073,2.615 0.427,0.219 10 false DRN7 5.385,0.427 5.615,0.646 0.229,0.219 10 false 40 5.385,0.75 5.615,0.969 0.229,0.219 10 false 29 5.385,1.073 5.615,1.292 0.229,0.219 10 false 39 5.375,1.406 5.604,1.625 0.229,0.219 10 false 28 5.375,1.729 5.604,1.948 0.229,0.219 10 false 38 5.375,2.063 5.604,2.281 0.229,0.219 10 false 27 5.375,2.323 5.604,2.542 0.229,0.219 10 false 26 5.635,3.521 5.979,3.74 0.344,0.219 10 false GRF 5.625,3.854 6.052,4.073 0.427,0.219 10 false GRFG 5.635,4.271 5.979,4.49 0.344,0.219 10 false GSN 5.635,4.594 6.063,4.813 0.427,0.219 10 false GSNG 5.646,4.927 5.99,5.094 0.344,0.167 10 false GCS 5.635,5.26 6.063,5.479 0.427,0.219 10 false GCSG 5.646,5.542 6.073,5.76 0.427,0.219 10 false DRN6 5.396,3.531 5.625,3.75 0.229,0.219 10 false 20 5.396,4.177 5.625,4.396 0.229,0.219 10 false 18 5.448,3.854 5.781,4.073 0.333,0.219 10 false 9 5.438,4.531 5.771,4.75 0.333,0.219 10 false 7 5.396,4.865 5.729,5.083 0.333,0.219 10 false 17 5.448,5.188 5.781,5.406 0.333,0.219 10 false 6 5.438,5.458 5.771,5.677 0.333,0.219 10 false 8 5.677,5.969 6.01,6.135 0.333,0.167 10 false A19 5.677,6.146 7.052,6.563 1.375,0.417 10 false Inverter with Converter Assembly (MG ECU) 0.167,2.865 2.719,3.115 2.552,0.25 10 false FCV with Motor Transaxle Assembly 3.177,2.719 3.51,2.885 0.333,0.167 10 false GG2 4.365,2.719 4.698,2.885 0.333,0.167 10 false AG5 3.219,5.885 3.552,6.052 0.333,0.167 10 false BB1 4.365,5.885 4.698,6.052 0.333,0.167 10 false BA1 4.75,0.625 4.979,0.844 0.229,0.219 10 false 12 4.75,0.948 4.979,1.167 0.229,0.219 10 false 13 4.771,1.271 5,1.49 0.229,0.219 10 false 14 4.76,1.615 4.99,1.833 0.229,0.219 10 false 15 4.76,1.938 4.99,2.156 0.229,0.219 10 false 16 4.76,2.26 4.99,2.479 0.229,0.219 10 false 17 3.583,0.625 3.813,0.844 0.229,0.219 10 false 2 3.594,0.948 3.823,1.167 0.229,0.219 10 false 3 3.594,1.281 3.823,1.5 0.229,0.219 10 false 4 3.594,1.604 3.823,1.823 0.229,0.219 10 false 5 3.583,1.948 3.813,2.167 0.229,0.219 10 false 6 3.594,2.271 3.823,2.49 0.229,0.219 10 false 7 4.76,2.521 4.99,2.74 0.229,0.219 10 false 18 3.594,2.542 3.823,2.76 0.229,0.219 10 false 8 2.948,2.531 3.177,2.75 0.229,0.219 10 false 8 2.948,2.271 3.177,2.49 0.229,0.219 10 false 7 2.948,1.948 3.177,2.167 0.229,0.219 10 false 6 2.948,1.615 3.177,1.833 0.229,0.219 10 false 5 2.938,1.302 3.167,1.521 0.229,0.219 10 false 4 2.938,0.958 3.167,1.177 0.229,0.219 10 false 3 2.938,0.625 3.167,0.844 0.229,0.219 10 false 2 4.063,0.625 4.292,0.844 0.229,0.219 10 false 12 4.063,0.948 4.292,1.167 0.229,0.219 10 false 13 4.073,1.281 4.302,1.5 0.229,0.219 10 false 14 4.073,1.604 4.302,1.823 0.229,0.219 10 false 15 4.073,1.948 4.302,2.167 0.229,0.219 10 false 16 4.073,2.271 4.302,2.49 0.229,0.219 10 false 17 4.063,2.531 4.292,2.75 0.229,0.219 10 false 18 4.75,3.74 4.979,3.958 0.229,0.219 10 false 38 4.76,4.063 4.99,4.281 0.229,0.219 10 false 39 4.76,4.406 4.99,4.625 0.229,0.219 10 false 40 4.76,4.729 4.99,4.948 0.229,0.219 10 false 61 4.76,5.052 4.99,5.271 0.229,0.219 10 false 62 4.76,5.385 4.99,5.604 0.229,0.219 10 false 63 4.76,5.656 4.99,5.875 0.229,0.219 10 false 64 3.583,3.74 3.813,3.958 0.229,0.219 10 false 10 3.583,4.083 3.813,4.302 0.229,0.219 10 false 11 3.583,4.396 3.813,4.615 0.229,0.219 10 false 12 3.583,4.719 3.813,4.938 0.229,0.219 10 false 18 3.573,5.063 3.802,5.281 0.229,0.219 10 false 19 3.583,5.396 3.813,5.615 0.229,0.219 10 false 20 3.583,5.677 3.813,5.896 0.229,0.219 10 false 21 2.896,3.75 3.125,3.969 0.229,0.219 10 false 10 2.906,4.083 3.135,4.302 0.229,0.219 10 false 11 2.896,4.406 3.125,4.625 0.229,0.219 10 false 12 2.896,4.729 3.125,4.948 0.229,0.219 10 false 18 2.896,5.052 3.125,5.271 0.229,0.219 10 false 19 2.896,5.385 3.125,5.604 0.229,0.219 10 false 20 2.896,5.677 3.125,5.896 0.229,0.219 10 false 21 4.063,5.656 4.292,5.875 0.229,0.219 10 false 64 4.063,5.396 4.292,5.615 0.229,0.219 10 false 63 4.073,5.073 4.302,5.292 0.229,0.219 10 false 62 4.073,4.729 4.302,4.948 0.229,0.219 10 false 61 4.063,4.406 4.292,4.625 0.229,0.219 10 false 40 4.073,4.073 4.302,4.292 0.229,0.219 10 false 39 4.063,3.75 4.292,3.969 0.229,0.219 10 false 38 2.906,2.906 4.01,3.344 1.104,0.438 10 false NO. 3 Floor Wire Connector 3.021,6.063 3.938,6.292 0.917,0.229 10 false Stack Wire

for RHD:
A480857E02
6.208,0.552 6.833,0.948 0.625,0.396 10 false Oscillation Circuit 0.635,0.25 1.583,0.469 0.948,0.219 10 false Excitation Coil 0.688,3.344 1.635,3.635 0.948,0.292 10 false Excitation Coil 1.76,0.417 2.104,0.635 0.344,0.219 10 false MRF 1.656,2.042 2.125,2.26 0.469,0.219 10 false MCSG 1.74,1.073 2.083,1.292 0.344,0.219 10 false MSN 1.667,1.385 2.167,1.625 0.5,0.24 10 false MSNG 1.75,1.729 2.094,1.948 0.344,0.219 10 false MCS 1.656,0.74 2.083,0.958 0.427,0.219 10 false MRFG 2.177,0.385 2.406,0.604 0.229,0.219 10 false 6 2.146,2.063 2.375,2.281 0.229,0.219 10 false 11 2.156,1.063 2.385,1.281 0.229,0.219 10 false 10 2.146,1.396 2.375,1.615 0.229,0.219 10 false 13 2.177,1.729 2.406,1.948 0.229,0.219 10 false 8 2.167,0.74 2.396,0.958 0.229,0.219 10 false 1 0.594,2.354 1.188,2.563 0.594,0.208 10 false G154 0.583,2.51 1.667,2.729 1.083,0.219 10 false Motor Resolver 1.771,3.542 2.115,3.76 0.344,0.219 10 false GRF 1.656,5.177 2.083,5.396 0.427,0.219 10 false GCSG 1.74,4.198 2.083,4.417 0.344,0.219 10 false GSN 1.667,4.531 2.094,4.75 0.427,0.219 10 false GSNG 1.76,4.844 2.104,5.01 0.344,0.167 10 false GCS 1.656,3.865 2.083,4.083 0.427,0.219 10 false GRFG 0.219,5.49 0.552,5.656 0.333,0.167 10 false B24 0.219,5.656 2.552,5.875 2.333,0.219 10 false FC Air Compressor Motor Resolver 2.135,3.542 2.469,3.76 0.333,0.219 10 false 1 2.146,5.177 2.375,5.396 0.229,0.219 10 false 7 2.146,4.188 2.375,4.406 0.229,0.219 10 false 2 2.146,4.542 2.375,4.76 0.229,0.219 10 false 6 2.146,4.865 2.375,5.083 0.229,0.219 10 false 3 2.135,3.854 2.365,4.073 0.229,0.219 10 false 5 0.24,6.073 2.906,6.354 2.667,0.281 10 false FC Air Compressor with Motor Assembly 5.646,0.417 5.99,0.635 0.344,0.219 10 false MRF 5.635,0.75 6.063,0.969 0.427,0.219 10 false MRFG 5.656,1.177 6,1.396 0.344,0.219 10 false MSN 5.656,1.49 6.208,1.719 0.552,0.229 10 false MSNG 5.656,1.833 6,2.052 0.344,0.219 10 false MCS 5.656,2.156 6.281,2.323 0.625,0.167 10 false MCSG 5.646,2.427 6.073,2.646 0.427,0.219 10 false DRN7 5.385,0.427 5.615,0.646 0.229,0.219 10 false 40 5.385,0.75 5.615,0.969 0.229,0.219 10 false 29 5.385,1.073 5.615,1.292 0.229,0.219 10 false 39 5.375,1.406 5.604,1.625 0.229,0.219 10 false 28 5.375,1.729 5.604,1.948 0.229,0.219 10 false 38 5.375,2.063 5.604,2.281 0.229,0.219 10 false 27 5.375,2.323 5.604,2.542 0.229,0.219 10 false 26 5.635,3.542 5.979,3.76 0.344,0.219 10 false GRF 5.635,3.875 6.063,4.094 0.427,0.219 10 false GRFG 5.635,4.302 5.979,4.521 0.344,0.219 10 false GSN 5.635,4.625 6.063,4.844 0.427,0.219 10 false GSNG 5.646,4.958 5.99,5.125 0.344,0.167 10 false GCS 5.646,5.281 6.073,5.5 0.427,0.219 10 false GCSG 5.646,5.563 6.073,5.781 0.427,0.219 10 false DRN6 5.396,3.531 5.625,3.75 0.229,0.219 10 false 20 5.396,4.177 5.625,4.396 0.229,0.219 10 false 18 5.458,3.854 5.792,4.073 0.333,0.219 10 false 9 5.438,4.531 5.771,4.75 0.333,0.219 10 false 7 5.396,4.865 5.729,5.083 0.333,0.219 10 false 17 5.448,5.188 5.781,5.406 0.333,0.219 10 false 6 5.438,5.458 5.771,5.677 0.333,0.219 10 false 8 5.667,5.979 6,6.146 0.333,0.167 10 false A18 5.677,6.156 7.042,6.573 1.365,0.417 10 false Inverter with Converter Assembly (MG ECU) 0.167,2.885 2.719,3.135 2.552,0.25 10 false FCV with Motor Transaxle Assembly 3.198,2.729 3.531,2.896 0.333,0.167 10 false GG2 4.375,2.719 4.708,2.885 0.333,0.167 10 false AG5 3.219,5.885 3.552,6.052 0.333,0.167 10 false BB1 4.365,5.885 4.698,6.052 0.333,0.167 10 false BA1 4.75,0.625 4.979,0.844 0.229,0.219 10 false 12 4.75,0.948 4.979,1.167 0.229,0.219 10 false 13 4.771,1.271 5,1.49 0.229,0.219 10 false 14 4.76,1.615 4.99,1.833 0.229,0.219 10 false 15 4.76,1.938 4.99,2.156 0.229,0.219 10 false 16 4.76,2.26 4.99,2.479 0.229,0.219 10 false 17 3.583,0.625 3.813,0.844 0.229,0.219 10 false 2 3.594,0.948 3.823,1.167 0.229,0.219 10 false 3 3.594,1.281 3.823,1.5 0.229,0.219 10 false 4 3.594,1.604 3.823,1.823 0.229,0.219 10 false 5 3.583,1.948 3.813,2.167 0.229,0.219 10 false 6 3.594,2.271 3.823,2.49 0.229,0.219 10 false 7 4.76,2.521 4.99,2.74 0.229,0.219 10 false 18 3.594,2.542 3.823,2.76 0.229,0.219 10 false 8 2.948,2.531 3.177,2.75 0.229,0.219 10 false 8 2.948,2.271 3.177,2.49 0.229,0.219 10 false 7 2.948,1.948 3.177,2.167 0.229,0.219 10 false 6 2.948,1.615 3.177,1.833 0.229,0.219 10 false 5 2.938,1.302 3.167,1.521 0.229,0.219 10 false 4 2.938,0.958 3.167,1.177 0.229,0.219 10 false 3 2.938,0.625 3.167,0.844 0.229,0.219 10 false 2 4.063,0.625 4.292,0.844 0.229,0.219 10 false 12 4.063,0.948 4.292,1.167 0.229,0.219 10 false 13 4.073,1.281 4.302,1.5 0.229,0.219 10 false 14 4.073,1.604 4.302,1.823 0.229,0.219 10 false 15 4.073,1.948 4.302,2.167 0.229,0.219 10 false 16 4.073,2.271 4.302,2.49 0.229,0.219 10 false 17 4.063,2.531 4.292,2.75 0.229,0.219 10 false 18 4.75,3.74 4.979,3.958 0.229,0.219 10 false 38 4.76,4.063 4.99,4.281 0.229,0.219 10 false 39 4.76,4.406 4.99,4.625 0.229,0.219 10 false 40 4.76,4.729 4.99,4.948 0.229,0.219 10 false 61 4.76,5.052 4.99,5.271 0.229,0.219 10 false 62 4.76,5.396 4.99,5.615 0.229,0.219 10 false 63 4.76,5.667 4.99,5.885 0.229,0.219 10 false 64 3.583,3.74 3.813,3.958 0.229,0.219 10 false 10 3.583,4.083 3.813,4.302 0.229,0.219 10 false 11 3.583,4.396 3.813,4.615 0.229,0.219 10 false 12 3.583,4.719 3.813,4.938 0.229,0.219 10 false 18 3.573,5.063 3.802,5.281 0.229,0.219 10 false 19 3.583,5.396 3.813,5.615 0.229,0.219 10 false 20 3.583,5.677 3.813,5.896 0.229,0.219 10 false 21 2.896,3.75 3.125,3.969 0.229,0.219 10 false 10 2.906,4.083 3.135,4.302 0.229,0.219 10 false 11 2.896,4.406 3.125,4.625 0.229,0.219 10 false 12 2.896,4.729 3.125,4.948 0.229,0.219 10 false 18 2.896,5.052 3.125,5.271 0.229,0.219 10 false 19 2.896,5.385 3.125,5.604 0.229,0.219 10 false 20 2.896,5.677 3.125,5.896 0.229,0.219 10 false 21 4.063,5.656 4.292,5.875 0.229,0.219 10 false 64 4.063,5.396 4.292,5.615 0.229,0.219 10 false 63 4.073,5.073 4.302,5.292 0.229,0.219 10 false 62 4.073,4.729 4.302,4.948 0.229,0.219 10 false 61 4.063,4.406 4.292,4.625 0.229,0.219 10 false 40 4.073,4.073 4.302,4.292 0.229,0.219 10 false 39 4.063,3.75 4.292,3.969 0.229,0.219 10 false 38 2.833,2.906 3.917,3.271 1.083,0.365 10 false NO. 3 Floor Wire Connector 3,6.063 3.885,6.417 0.885,0.354 10 false Stack Wire

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 5 seconds or more.*

2.

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC IntermittentOperation.

3.

Push the P position switch (shift position indicator) to select park (P), turn the ignition switch to ON (READY) and wait until the FCsystem is started. Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY).

- FC system is started: "Working" is displayed for the Data List item "FC Work Mode" and "FC Intermittent Operation" is OFF.

4.

With the FC system operating, wait for 15 seconds or more.

5.

Drive the vehicle in drive (D) for 5 m (16 ft.) or more.

6.

Drive the vehicle in reverse (R) for 5 m (16 ft.) or more.

7.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




*: Lightly wiggle the connectors and wire harnesses up and down and right and left.

NOTICE:

If excessive pressure is applied while the connectors and wire harnesses are wiggled, they may be damaged. After the inspection, make sure to return the wire harnesses and clamps to their original position.


CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removal of the service plug grips of both FC stack assembly and EV battery, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1E8649, P1E8738 or P1E8800 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Relevant DTC
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
C361311C86
0.115,0.781 0.521,1.146 0.406,0.365 0.115,1.292 0.521,1.656 0.406,0.365 1.729,1 1.823,0.479 true 1.333,1.844 1.656,1.083 true 1.813,1.854 1.74,1.073 true 1.208,0.49 1.646,1.021 true 2.365,1.844 1.896,1.094 true 1.896,1 2.333,0.469 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.698,0.292 2.135,0.448 0.438,0.156 10 false GSNG 1.729,1.917 2.063,2.104 0.333,0.188 10 false GSN 2.333,1.917 2.667,2.073 0.333,0.156 10 false GRF 0.208,0.896 0.667,1.094 0.458,0.198 10 false A19 0.958,0.302 1.573,0.5 0.615,0.198 10 false GCSG 1.104,1.917 1.438,2.083 0.333,0.167 10 false GCS 2.365,0.281 2.979,0.479 0.615,0.198 10 false GRFG 0.219,1.385 0.677,1.583 0.458,0.198 10 false A18 0.563,0.906 1.021,1.104 0.458,0.198 10 false *A 0.573,1.406 1.031,1.604 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-20 (GRF) - Body ground Ignition switch ON Below 1 V
A19-9 (GRFG) - Body ground Ignition switch ON Below 1 V
A19-18 (GSN) - Body ground Ignition switch ON Below 1 V
A19-7 (GSNG) - Body ground Ignition switch ON Below 1 V
A19-17 (GCS) - Body ground Ignition switch ON Below 1 V
A19-6 (GCSG) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-20 (GRF) - Body ground Ignition switch ON Below 1 V
A18-9 (GRFG) - Body ground Ignition switch ON Below 1 V
A18-18 (GSN) - Body ground Ignition switch ON Below 1 V
A18-7 (GSNG) - Body ground Ignition switch ON Below 1 V
A18-17 (GCS) - Body ground Ignition switch ON Below 1 V
A18-6 (GCSG) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

4.CHECK FC AIR COMPRESSOR MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FC AIR COMPRESSOR MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C361311C86
0.115,0.781 0.521,1.146 0.406,0.365 0.115,1.292 0.521,1.656 0.406,0.365 1.729,1 1.823,0.479 true 1.333,1.844 1.656,1.083 true 1.813,1.854 1.74,1.073 true 1.208,0.49 1.646,1.021 true 2.365,1.844 1.896,1.094 true 1.896,1 2.333,0.469 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.698,0.292 2.135,0.448 0.438,0.156 10 false GSNG 1.729,1.917 2.063,2.104 0.333,0.188 10 false GSN 2.333,1.917 2.667,2.073 0.333,0.156 10 false GRF 0.208,0.896 0.667,1.094 0.458,0.198 10 false A19 0.958,0.302 1.573,0.5 0.615,0.198 10 false GCSG 1.104,1.917 1.438,2.083 0.333,0.167 10 false GCS 2.365,0.281 2.979,0.479 0.615,0.198 10 false GRFG 0.219,1.385 0.677,1.583 0.458,0.198 10 false A18 0.563,0.906 1.021,1.104 0.458,0.198 10 false *A 0.573,1.406 1.031,1.604 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-20 (GRF) - A19-9 (GRFG) Ignition switch off 6.5 to 21.5 Ω
A19-18 (GSN) - A19-7 (GSNG) Ignition switch off 10.0 to 37.5 Ω
A19-17 (GCS) - A19-6 (GCSG) Ignition switch off 9.0 to 35.5 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-20 (GRF) - A18-9 (GRFG) Ignition switch off 6.5 to 21.5 Ω
A18-18 (GSN) - A18-7 (GSNG) Ignition switch off 10.0 to 37.5 Ω
A18-17 (GCS) - A18-6 (GCSG) Ignition switch off 9.0 to 35.5 Ω


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)


Standard Resistance (Check for Short):
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-20 (GRF) or A19-9 (GRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-18 (GSN) or A19-7 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-17 (GCS) or A19-6 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-20 (GRF) or A18-9 (GRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-18 (GSN) or A18-7 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-17 (GCS) or A18-6 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

14.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)
5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
C361311C87
0.083,0.792 0.521,1.125 0.438,0.333 0.083,1.24 0.521,1.573 0.438,0.333 1.813,1.26 1.781,0.438 true 1.125,1.875 1.729,1.333 true 1.823,1.865 1.813,1.323 true 1.073,0.5 1.729,1.271 true 2.396,1.896 1.885,1.333 true 1.896,1.26 2.458,0.458 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.604,0.229 2.219,0.427 0.615,0.198 10 false MSNG 1.708,1.927 2.042,2.104 0.333,0.177 10 false MSN 0.938,1.917 1.406,2.104 0.469,0.188 10 false MCS 0.198,0.875 0.656,1.073 0.458,0.198 10 false A19 0.802,0.26 1.417,0.458 0.615,0.198 10 false MCSG 2.302,1.917 2.917,2.115 0.615,0.198 10 false MRF 2.406,0.24 3.021,0.438 0.615,0.198 10 false MRFG 0.208,1.323 0.667,1.521 0.458,0.198 10 false A18 0.573,0.885 1.031,1.083 0.458,0.198 10 false *A 0.573,1.333 1.031,1.531 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-40 (MRF) - Body ground Ignition switch ON Below 1 V
A19-29 (MRFG) - Body ground Ignition switch ON Below 1 V
A19-39 (MSN) - Body ground Ignition switch ON Below 1 V
A19-28 (MSNG) - Body ground Ignition switch ON Below 1 V
A19-38 (MCS) - Body ground Ignition switch ON Below 1 V
A19-27 (MCSG) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-40 (MRF) - Body ground Ignition switch ON Below 1 V
A18-29 (MRFG) - Body ground Ignition switch ON Below 1 V
A18-39 (MSN) - Body ground Ignition switch ON Below 1 V
A18-28 (MSNG) - Body ground Ignition switch ON Below 1 V
A18-38 (MCS) - Body ground Ignition switch ON Below 1 V
A18-27 (MCSG) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

6.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C361311C87
0.083,0.792 0.521,1.125 0.438,0.333 0.083,1.24 0.521,1.573 0.438,0.333 1.813,1.26 1.781,0.438 true 1.125,1.875 1.729,1.333 true 1.823,1.865 1.813,1.323 true 1.073,0.5 1.729,1.271 true 2.396,1.896 1.885,1.333 true 1.896,1.26 2.458,0.458 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.604,0.229 2.219,0.427 0.615,0.198 10 false MSNG 1.708,1.927 2.042,2.104 0.333,0.177 10 false MSN 0.938,1.917 1.406,2.104 0.469,0.188 10 false MCS 0.198,0.875 0.656,1.073 0.458,0.198 10 false A19 0.802,0.26 1.417,0.458 0.615,0.198 10 false MCSG 2.302,1.917 2.917,2.115 0.615,0.198 10 false MRF 2.406,0.24 3.021,0.438 0.615,0.198 10 false MRFG 0.208,1.323 0.667,1.521 0.458,0.198 10 false A18 0.573,0.885 1.031,1.083 0.458,0.198 10 false *A 0.573,1.333 1.031,1.531 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-40 (MRF) - A19-29 (MRFG) Ignition switch off 8.8 to 14.8 Ω
A19-39 (MSN) - A19-28 (MSNG) Ignition switch off 16.1 to 28.1 Ω
A19-38 (MCS) - A19-27 (MCSG) Ignition switch off 18.0 to 30.1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-40 (MRF) - A18-29 (MRFG) Ignition switch off 8.8 to 14.8 Ω
A18-39 (MSN) - A18-28 (MSNG) Ignition switch off 16.1 to 28.1 Ω
A18-38 (MCS) - A18-27 (MCSG) Ignition switch off 18.0 to 30.1 Ω


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)


Standard Resistance (Check for Short):
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-40 (MRF) or A19-29 (MRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-39 (MSN) or A19-28 (MSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-38 (MCS) or A19-27 (MCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-40 (MRF) or A18-29 (MRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-39 (MSN) or A18-28 (MSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-38 (MCS) or A18-27 (MCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

7.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

NG

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)
7.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

9.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A479479

Check the connection condition of the motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

10.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER CONNECTOR)
a.
A480856

Check the connection condition of the FC air compressor motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C




A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

12.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A479479

Check the connection condition of the motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the G154 motor resolver connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480860C03
4.74,0.292 5.198,0.646 0.458,0.354 1.583,0.271 2.042,0.656 0.458,0.385 5.542,0.292 6,0.646 0.458,0.354 5.135,2.271 5.427,1.594 true 2.094,1.24 2.74,2.26 true 6.448,0.49 6.344,0.49 6.344,0.49 5.542,1.469 true 5.646,2.25 5.542,1.594 true 6.385,2.292 5.656,1.49 true 6.042,2.292 5.667,1.604 true 0.76,2.271 1.438,1.24 true 1.948,1.396 2.417,2.26 true 1.49,2.24 1.698,1.375 true 2.01,2.24 1.813,1.542 true 1.073,2.292 1.552,1.521 true 4.635,2.292 5.417,1.49 true 0.313,0.229 0.625,0.427 0.313,0.198 10 false *a 3.469,0.323 3.781,0.521 0.313,0.198 10 false *b 1.656,0.385 2.042,0.594 0.385,0.208 10 false G154 4.854,0.385 5.271,0.604 0.417,0.219 10 false A19 5.958,2.313 6.448,2.531 0.49,0.219 10 false MRF 0.396,2.302 0.885,2.521 0.49,0.219 10 false MRFG 2.406,2.292 2.896,2.51 0.49,0.219 10 false MSN 1.938,2.292 2.427,2.51 0.49,0.219 10 false MSNG 1.365,2.292 1.854,2.51 0.49,0.219 10 false MCS 0.896,2.302 1.385,2.521 0.49,0.219 10 false MCSG 2.75,2.292 3.24,2.51 0.49,0.219 10 false MRF 6.365,2.313 6.854,2.531 0.49,0.219 10 false MRFG 5.552,2.302 6.042,2.521 0.49,0.219 10 false MSN 6.5,0.427 6.99,0.646 0.49,0.219 10 false MSNG 4.969,2.313 5.458,2.531 0.49,0.219 10 false MCS 4.281,2.302 4.771,2.521 0.49,0.219 10 false MCSG 5.667,0.396 6.083,0.615 0.417,0.219 10 false A18 5.25,0.396 5.667,0.615 0.417,0.219 10 false *A 6.073,0.417 6.49,0.635 0.417,0.219 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Motor Resolver)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,G154)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

A19-40(MRF) - G154-6(MRF) Ignition switch off below 1 Ω
A19-29(MRFG) - G154-1(MRFG) Ignition switch off below 1 Ω
A19-39(MSN) - G154-10(MSN) Ignition switch off below 1 Ω
A19-28(MSNG) - G154-13(MSNG) Ignition switch off below 1 Ω
A19-38(MCS) - G154-8(MCS) Ignition switch off below 1 Ω
A19-27(MCSG) - G154-11(MCSG) Ignition switch off below 1 Ω
A19-40 (MRF) or G154-6 (MRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-29 (MRFG) or G154-1 (MRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-39 (MSN) or G154-10 (MSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-28 (MSNG) or G154-13 (MSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-38 (MCS) or G154-8 (MCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-27 (MCSG) or G154-11 (MCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,G154)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

A18-40(MRF) - G154-6(MRF) Ignition switch off below 1 Ω
A18-29(MRFG) - G154-1(MRFG) Ignition switch off below 1 Ω
A18-39(MSN) - G154-10(MSN) Ignition switch off below 1 Ω
A18-28(MSNG) - G154-13(MSNG) Ignition switch off below 1 Ω
A18-38(MCS) - G154-8(MCS) Ignition switch off below 1 Ω
A18-27(MCSG) - G154-11(MCSG) Ignition switch off below 1 Ω
A18-40 (MRF) or G154-6 (MRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-29 (MRFG) or G154-1 (MRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-39 (MSN) or G154-10 (MSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-28 (MSNG) or G154-13 (MSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-38 (MCS) or G154-8 (MCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A18-27 (MCSG) or G154-11 (MCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


HINT:

The drive motor resolver is not available as a supply part. If it requires replacement, replace the FCV with motor transaxle assembly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G154 motor resolver connector.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK CONNECTOR CONNECTION CONDITION (STACK WIRE)
a.
A481468

Check the connection condition of the stack wire connnector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C




A

15.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK CONNECTOR CONNECTION CONDITION (FC AIR COMPRESSOR MOTOR RESOLVER CONNECTOR)
a.
A480856

Check the connection condition of the FC air compressor motor resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C




A

16.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - FC AIR COMPRESSOR MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the B24 FC air compressor motor resolver connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480859C03
1.448,0.375 1.896,0.719 0.448,0.344 4.729,0.365 5.177,0.688 0.448,0.323 5.531,0.365 5.979,0.688 0.448,0.323 0.865,2.177 1.427,1.375 true 1.875,2.219 1.573,1.375 true 2.604,2.219 1.719,1.354 true 1.115,2.177 1.448,1.5 true 1.49,2.208 1.573,1.5 true 2.177,2.198 1.688,1.5 true 4.333,2.198 5.313,1.198 true 5.125,2.219 5.417,1.188 true 6.208,2.208 5.667,1.188 true 5.323,1.302 4.708,2.219 true 5.438,1.323 5.531,2.229 true 5.656,1.313 5.927,2.229 true 0.583,0.25 0.896,0.406 0.313,0.156 10 false *a 3.896,0.198 4.208,0.354 0.313,0.156 10 false *b 0.573,2.219 1.031,2.417 0.458,0.198 10 false GRF 1.75,2.229 2.208,2.427 0.458,0.198 10 false GSN 2.51,2.219 2.969,2.417 0.458,0.198 10 false GCS 1.563,0.458 2.021,0.656 0.458,0.198 10 false B24 0.917,2.219 1.531,2.417 0.615,0.198 10 false GRFG 1.323,2.219 1.938,2.417 0.615,0.198 10 false GSNG 2.094,2.219 2.708,2.417 0.615,0.198 10 false GCSG 4.844,0.448 5.302,0.646 0.458,0.198 10 false A19 4.417,2.24 4.875,2.438 0.458,0.198 10 false GCS 5.396,2.24 5.854,2.438 0.458,0.198 10 false GSN 5.854,2.24 6.313,2.438 0.458,0.198 10 false GRF 3.958,2.229 4.573,2.427 0.615,0.198 10 false GCSG 4.875,2.24 5.49,2.438 0.615,0.198 10 false GSNG 6.198,2.229 6.813,2.427 0.615,0.198 10 false GRFG 5.646,0.448 6.104,0.646 0.458,0.198 10 false A18 5.219,0.469 5.677,0.667 0.458,0.198 10 false *A 6.042,0.458 6.5,0.656 0.458,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to FC Air Compressor Motor Resolver)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,B24)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

A19-20(GRF) - B24-1(GRF) Ignition switch off below 1 Ω
A19-9(GRFG) - B24-5(GRFG) Ignition switch off below 1 Ω
A19-18(GSN) - B24-2(GSN) Ignition switch off below 1 Ω
A19-7(GSNG) - B24-6(GSNG) Ignition switch off below 1 Ω
A19-17(GCS) - B24-3(GCS) Ignition switch off below 1 Ω
A19-6(GCSG) - B24-7(GCSG) Ignition switch off below 1 Ω
A19-20 (GRF) or B24-1 (GRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-9 (GRFG) or B24-5 (GRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-18 (GSN) or B24-2 (GSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-7 (GSNG) or B24-6 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-17 (GCS) or B24-3 (GCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-6 (GCSG) or B24-7 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,B24)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(B24)Engine Compartment>No. 2 Stack Wire>FC Air Compressor with Motor Assembly

A19-20 (GRF) - B24-1 (GRF) Ignition switch off below 1 Ω
A19-9 (GRFG) - B24-5 (GRFG) Ignition switch off below 1 Ω
A19-18 (GSN) - B24-2 (GSN) Ignition switch off below 1 Ω
A19-7 (GSNG) - B24-6 (GSNG) Ignition switch off below 1 Ω
A19-17 (GCS) - B24-3 (GCS) Ignition switch off below 1 Ω
A19-6 (GCSG) - B24-7 (GCSG) Ignition switch off below 1 Ω
A19-20 (GRF) or B24-1 (GRF) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-9 (GRFG) or B24-5 (GRFG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-18 (GSN) or B24-2 (GSN) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-7 (GSNG) or B24-6 (GSNG) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-17 (GCS) or B24-3 (GCS) - Body ground and other terminals Ignition switch off 1 MΩ or higher
A19-6 (GCSG) or B24-7 (GCSG) - Body ground and other terminals Ignition switch off 1 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B24 FC air compressor motor resolver connector.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR