42110F
1.TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY
Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts (B).
| *1 | Engine Lifter | *2 | Wooden Block |
| *3 | Attachment | - | - |
Make sure to secure the rear axle beam assembly to prevent it from dropping.
Temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts (A) and 2 nuts.
Since stopper nuts are used, turn the bolts.
Insert the bolts with the threaded end facing the outside of the vehicle.
48258C
2.INSTALL REAR LOWER COIL SPRING INSULATOR LH
48258B
3.INSTALL REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as the LH side.
48259A
4.INSTALL REAR UPPER COIL SPRING INSULATOR LH
48257C
5.INSTALL REAR UPPER COIL SPRING INSULATOR RH
Perform the same procedure as the LH side.
48231B
6.INSTALL REAR COIL SPRING LH
48231A
7.INSTALL REAR COIL SPRING RH
Perform the same procedure as the LH side.
42450B
8.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH
42450A
9.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH
Perform the same procedure as the LH side.
42403
10.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
Install the 2 rear brake drum sub-assemblies (See page Brake>BRAKE (REAR)>REAR BRAKE>INSTALLATION).
46430
11.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
Install the new No. 1 parking brake cable clamp to the No. 3 parking brake cable assembly (See page Brake>PARKING BRAKE>PARKING BRAKE CABLE>INSTALLATION).
Install the No. 3 parking brake cable assembly with the bolt and a No. 1 parking brake cable clamp.
46420
12.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY
Perform the same procedure as for the No. 3 parking brake cable assembly.
47324
13.INSTALL NO. 4 REAR BRAKE TUBE
Install the No. 4 rear brake tube to the rear axle beam assembly with the nut.
Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.
Using a union nut wrench, install the No. 4 rear brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.
Do not bend or damage the brake line.
Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
47323
14.INSTALL NO. 3 REAR BRAKE TUBE
Perform the same procedure as for the No. 4 rear brake tube.
89516D
15.INSTALL SKID CONTROL SENSOR WIRE LH
89516C
16.INSTALL SKID CONTROL SENSOR WIRE RH
Perform the same procedure as the LH side.
89516D
17.CONNECT SKID CONTROL SENSOR WIRE LH
89516C
18.CONNECT SKID CONTROL SENSOR WIRE RH
Perform the same procedure as the LH side.
19.ADJUST REAR DRUM BRAKE SHOE CLEARANCE
20.INSTALL REAR WHEEL
21. STABILIZE SUSPENSION
Lower the vehicle from the jack.
Bounce the vehicle up and down several times to stabilize the suspension.
42110F
22.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY
Suspend the jack on the spring seat of the rear axle beam assembly and adjust the length of the rear shock absorber assembly to the reference value.
| *A | LH Side |
| *B | RH Side |
220 mm (8.66 in.)
Fully tighten the 2 bolts.
48540
23.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
48530
24.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH
Perform the same procedure as the LH side.
25.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
26.BLEED BRAKE LINE
89407A
27.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
28.INSPECT REAR WHEEL ALIGNMENT
29.CHECK FOR SPEED SENSOR SIGNAL