Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › from 2015.11
RM2170E _53 Suspension _057018 REAR SUSPENSION _0278014 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  INSTALLATION  


PROCEDURE

Hide 42110F 1.TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.

Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts (B).

C249969E03
2.865,1.688 2.667,1.688 2.667,1.688 2.667,1.802 true 4.427,1.688 4.604,1.688 4.604,1.688 4.604,1.802 true 2.25,1.646 2.427,1.646 false 5.021,1.635 4.906,1.635 false 1.698,1.854 1.594,1.854 1.594,1.854 1.594,2.219 false 2.604,1.813 2.781,1.958 0.177,0.146 10 false *3 4.531,1.813 4.708,1.958 0.177,0.146 10 false *3 2.448,1.573 2.625,1.719 0.177,0.146 10 false *2 4.729,1.563 4.906,1.708 0.177,0.146 10 true *2 0.281,1.833 0.5,2.01 0.219,0.177 10 false (B) 6.688,1.833 6.906,2.01 0.219,0.177 10 false (B) 1.76,1.49 1.979,1.667 0.219,0.177 10 false (A) 5.313,1.5 5.531,1.677 0.219,0.177 10 false (A) 1.5,2.229 1.677,2.375 0.177,0.146 10 false *1

Text in Illustration
*1 Engine Lifter *2 Wooden Block
*3 Attachment - -

NOTICE:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts (A) and 2 nuts.

NOTICE:

Since stopper nuts are used, turn the bolts.


HINT:

Insert the bolts with the threaded end facing the outside of the vehicle.



Hide 48258C 2.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 3.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as the LH side.


Hide 48259A 4.INSTALL REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 5.INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as the LH side.


Hide 48231B 6.INSTALL REAR COIL SPRING LH

Hide 48231A 7.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as the LH side.


Hide 42450B 8.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 9.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 42403 10.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

a.

Install the 2 rear brake drum sub-assemblies (See page Brake>BRAKE (REAR)>REAR BRAKE>INSTALLATION).


Hide 46430 11.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Install the new No. 1 parking brake cable clamp to the No. 3 parking brake cable assembly (See page Brake>PARKING BRAKE>PARKING BRAKE CABLE>INSTALLATION).


b.

Install the No. 3 parking brake cable assembly with the bolt and a No. 1 parking brake cable clamp.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 46420 12.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Perform the same procedure as for the No. 3 parking brake cable assembly.


Hide 47324 13.INSTALL NO. 4 REAR BRAKE TUBE

a.

Install the No. 4 rear brake tube to the rear axle beam assembly with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.


c.

Using a union nut wrench, install the No. 4 rear brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47323 14.INSTALL NO. 3 REAR BRAKE TUBE

HINT:

Perform the same procedure as for the No. 4 rear brake tube.


Hide 89516D 15.INSTALL SKID CONTROL SENSOR WIRE LH

Hide 89516C 16.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 89516C 18.CONNECT SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 19.ADJUST REAR DRUM BRAKE SHOE CLEARANCE

Hide 20.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 21. STABILIZE SUSPENSION

a.

Lower the vehicle from the jack.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 42110F 22.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.
C249972E01
0.355,2.475 0.544,2.664 0.189,0.189 10 *A 1.85,2.475 2.039,2.664 0.189,0.189 10 *B

Suspend the jack on the spring seat of the rear axle beam assembly and adjust the length of the rear shock absorber assembly to the reference value.

Text in Illustration
*A LH Side
*B RH Side

Length of shock absorber:

220 mm (8.66 in.)



b.

Fully tighten the 2 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


Hide 48540 23.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 24.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 25.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 26.BLEED BRAKE LINE

Hide 89407A 27.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)