Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › from 2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278128 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 87201B 1.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.

Engage the 3 claws to install the No. 2 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 2 air duct subassembly are cracked or deformed, make sure to replace the air duct with a new one. Failure to do so may cause the No. 2 air duct subassembly to fall off or noise to occur.



Hide 87201F 2.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

a.

Engage the 3 claws to install the No. 3 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 3 air duct subassembly are cracked or deformed, make sure to replace the air duct with a new one. Failure to do so may cause the No. 2 air duct subassembly to fall off or noise to occur.



Hide 82210K 3.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

Connect each connector.


b.

Engage each clamp to install the air conditioning harness assembly.


Hide 88650N 4.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

a.

Temporarily install the air conditioning amplifier assembly as shown in the illustration.

E238233


b.

Install the air conditioning amplifier assembly with the screw.


c.

Connect the connector.


Hide 88897P 5.INSTALL ASPIRATOR

a.

Engage the 2 claws and install the aspirator.


Hide 87050 6.INSTALL AIR CONDITIONING RADIATOR ASSEMBLY

a.

Install the air conditioning radiator assembly with the 3 screws.


b.

Connect the connector.


Hide 7.TEMPORARILY TIGHTEN AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily tighten the air conditioning unit with the 3 bolts and nut.

NOTICE:

To prevent damage to the installation bracket for the air conditioning unit, be sure to support the air conditioning unit in place.



Hide 88539J 8.CONNECT DRAIN COOLER HOSE

a.
E390729E01
1.854,0.833 2.531,0.479 false 2.552,0.354 2.792,0.583 0.24,0.229 10 true *a 1.375,2.052 1.688,2.333 0.313,0.281 10 false *b

Install the drain cooler hose as shown in the illustration.

Text in Illustration
*a UP Mark
*b 60°

NOTICE:
·

Install the drain hose with its UP mark facing upward, within the 60 degree range shown in the illustration.

·

Install the drain hose without twisting it.




Hide 55950G 9.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.

Engage the 2 claws and 3 guides to install the defroster nozzle assembly.


Hide 55330B 10.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Install the instrument panel reinforcement with the 8 bolts.

E249753E02
0.406,0.146 0.615,0.344 0.208,0.198 10 true *1 2.698,0.135 2.896,0.323 0.198,0.188 10 true *1 5,0.135 5.198,0.333 0.198,0.198 10 true *1 5.479,4.948 5.688,5.125 0.208,0.177 10 true *1 3.375,5.344 3.573,5.531 0.198,0.188 10 true *2 0.167,5.354 0.354,5.542 0.188,0.188 10 true *2

Text in Illustration
*1 Bolt *2 Screw

Torque:
for Type A : 19 N*m (194 kgf*cm, 14 ft.*lbf)
for Type B : 29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:
E338400E01
0.406,1.167 0.625,1.594 0.219,0.427 10 false a 2.021,1.219 2.24,1.646 0.219,0.427 10 false b 1.052,0.354 1.406,0.813 0.354,0.458 12 false *A 2.677,0.365 3.031,0.823 0.354,0.458 12 false *B

There are three types of bolts and the tightening torque depends on the type of bolt used as shown in the illustration. Therefore, confirm the tightening torque before installing the bolt.

Text in Illustration
*A for Type A
*B for Type B

Area Measurement
a 14.5 to 15.5 mm (0.571 to 0.610 in.)
b 17.5 to 18.5 mm (0.689 to 0.728 in.)



b.

Temporarily tighten the 3 screws.


Hide 82141 11.CONNECT INSTRUMENT PANEL WIRE (for LHD)

a.

Engage each clamp.

E249752E02
2.813,0.573 3.125,1.042 true 2.635,0.49 2.854,0.698 0.219,0.208 10 true *1

Text in Illustration
*1 Earth Wire - -


b.

Connect the connector.


c.

Install the earth wire with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.

Engage each clamp.

E249751E02
6.708,1.406 6.26,1.073 true 3.052,0.5 3.49,0.74 true 6.729,1.313 6.958,1.51 0.229,0.198 10 true *1 2.844,0.396 3.042,0.563 0.198,0.167 10 true *1 3.552,0.396 3.781,0.573 0.229,0.177 10 true *2 6.667,0.688 6.875,0.896 0.208,0.208 10 true *2 1.042,1.344 1.281,1.542 0.24,0.198 10 true *3

Text in Illustration
*1 Earth Wire *2 Bolt <A>
*2 Bolt <B> - -


e.

Connect the connector.


f.

Install the bolt <B>.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


g.

Install the 2 earth wires with the 2 bolts <A>.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


h.
E238211

for RH Side:

i.

Engage each clamp and connect the connector holder.


ii.

Install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


iii.

Connect each connector.



i.
E238209

for LH Side:

i.

Engage each clamp and connect the connector holder.


ii.

Connect the connector to the connector holder.


iii.

Install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


iv.

Connect each connector.



Hide 82141 12.CONNECT INSTRUMENT PANEL WIRE (for RHD)

a.

Engage each clamp.

E249747E02
1.896,5.854 1.885,6.292 true 1.823,6.313 2.021,6.51 0.198,0.198 10 true *1 2.083,5.969 2.292,6.156 0.208,0.188 10 true *2 1.594,1.385 1.792,1.583 0.198,0.198 10 true *3

Text in Illustration
*1 Earth Wire *2 Bolt <A>
*3 Bolt <B> - -


b.

Connect the connector.


c.

Install the bolt <B>.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Install the earth wire with the bolt <A>.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Engage each clamp.

E249746E02
5.458,0.615 5.99,0.469 true 1.458,1.323 1.021,0.792 true 0.865,0.688 1.073,0.875 0.208,0.188 10 true *1 5.271,0.542 5.458,0.75 0.188,0.208 10 true *1

Text in Illustration
*1 Earth Wire - -


f.

Connect each connector.


g.

Install the 2 earth wires with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


h.
E235014

for LH Side:

i.

Engage each clamp and connect the connector holder.


ii.

Install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


iii.

Connect each connector.



i.
E235012

for RH Side:

i.

Engage each clamp and connect the connector holder.


ii.

Connect the connector to the connector holder.


iii.

Install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


iv.

Connect each connector.



Hide 55306A 13.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)

a.
E249366N01
0.76,0.479 1.094,0.438 true 2.458,2.094 2.24,1.823 true 0.667,1.99 1.01,1.635 true 0.958,3.083 1.406,2.917 true 0.469,1.948 0.635,2.125 0.167,0.177 10 true *1 2.49,2.052 2.688,2.25 0.198,0.198 10 true *3 0.563,0.396 0.729,0.594 0.167,0.198 10 true *4 0.74,2.979 0.938,3.177 0.198,0.198 10 true *2

Install the No. 1 instrument panel brace sub-assembly with the bolt <A>, <B>, screw and nut.

Text in Illustration
*1 Bolt <A>
*2 Bolt <B>
*3 Screw
*4 Nut

Torque:
Bolt <B> : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Nut : 13 N*m (133 kgf*cm, 10 ft.*lbf)

HINT:

Do not fully tighten the screw.



b.

Engage each clamp.


Hide 55306A 14.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)

a.
E245864E02
2.24,0.542 2.563,0.76 true 0.792,1.25 1.146,1.302 true 2.292,2.823 2.021,2.958 true 2.313,2.74 2.5,2.927 0.188,0.188 10 true *1 0.625,1.167 0.813,1.354 0.188,0.188 10 true *2 2.573,0.688 2.76,0.875 0.188,0.188 10 true *3

Install the No. 1 instrument panel brace sub-assembly with the bolt, screw and nut.

Text in Illustration
*1 Bolt
*2 Screw
*3 Nut

Torque:
Bolt : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Nut : 13 N*m (133 kgf*cm, 10 ft.*lbf)

HINT:

Do not fully tighten the screw.



b.

Engage each clamp.


Hide 15.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Tighten install the 2 No. 1 air duct bolts.

E249754E02
0.333,0.458 0.542,0.656 0.208,0.198 10 true *3 2.188,0.219 2.396,0.417 0.208,0.198 10 true *3 5.448,0.406 5.656,0.604 0.208,0.198 10 true *3 3.938,1.99 4.146,2.188 0.208,0.198 10 true *1 5.688,1.938 5.885,2.115 0.198,0.177 10 true *1 4.865,6.156 5.052,6.333 0.188,0.177 10 true *2 6.344,6.198 6.552,6.396 0.208,0.198 10 true *4 2.448,6.156 2.656,6.354 0.208,0.198 10 true *3 2.646,6.146 2.875,6.354 0.229,0.208 10 true (4) 5.031,6.146 5.313,6.333 0.281,0.188 10 true (6) 6.531,6.198 6.844,6.396 0.313,0.198 10 true (5) 5.646,0.406 5.896,0.583 0.25,0.177 10 true (3) 2.365,0.208 2.635,0.427 0.271,0.219 10 true (2) 0.51,0.448 0.75,0.656 0.24,0.208 10 true (1)

Text in Illustration
*1 No. 1 air duct bolt *2 Bolt
*3 Screw *4 Nut

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Install the bolt, nut and 4 screws in the order shown in the illustration.

Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Screw (1), (2), (3) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 58510D 16.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Install the front floor carpet assembly.


Hide 89650 19.INSTALL POWER STEERING ECU ASSEMBLY (for LHD)

Hide 89650 20.INSTALL POWER STEERING ECU ASSEMBLY (for RHD)

Hide 82730 21.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)

Hide 82730 22.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)

Hide 25.INSTALL STEERING COLUMN ASSEMBLY

Hide 55303B 26.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 87209 27.CONNECT WATER HOSE SUB-ASSEMBLY

a.
E240547E03
1.729,3.229 1.26,3.052 false 2.615,2.958 2.854,3.198 0.24,0.24 10 false *c 1,1.698 1.188,1.885 0.188,0.188 10 true A 0.99,2.573 1.229,2.813 0.24,0.24 10 false *a 1.063,2.948 1.302,3.188 0.24,0.24 10 false *b

Connect the water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.

Text in Illustration
*a View A
*b Water Hose Sub-assembly Marking (White)
*c Clip installation angle (60° to 150°)

NOTICE:

Do not apply excessive force to the water hose sub-assembly.



Hide 87246A 28.CONNECT HEATER WATER OUTLET HOSE A

a.
E240548E03
1.708,3.365 1.042,4.031 false 1.073,1.615 1.281,1.823 0.208,0.208 10 true A 0.833,2.604 1.063,2.823 0.229,0.219 10 false *a 0.854,3.99 1.083,4.208 0.229,0.219 10 false *b 1.875,2.469 2.104,2.688 0.229,0.219 10 false *c

Connect heater water outlet hose A with the marking (purple) facing up and engage the clip within the area shown in the illustration.

Text in Illustration
*a View A
*b Heater Water Outlet Hose A Marking (Purple)
*c Clip installation angle (-45° to 45°)

NOTICE:

Do not apply excessive force to heater water outlet hose A.



Hide 88706 29.CONNECT LIQUID PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the liquid pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and fitting surface of the liquid pipe sub-assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the liquid pipe sub-assembly.


d.

Install the liquid pipe sub-assembly.


Hide 88707 30.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.


d.

Connect the suction pipe sub-assembly.


e.
E240549

Rotate the hook connector in the direction indicated by the arrow in the illustration.


f.

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55701J 31.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 32.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55815E 33.INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 34.INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55735B 35.INSTALL FRONT AIR SHUTTER SEAL (for LHD)

Hide 55735B 36.INSTALL FRONT AIR SHUTTER SEAL (for RHD)

Hide 55722C 37.INSTALL INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 38.INSTALL INNER COWL TOP TO COWL BRACE (for RHD)

Hide 39.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 41.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR (for Engine)

Hide 42.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT