Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0128  Thermostat  


DESCRIPTION

HINT:

This DTC relates to the water inlet with thermostat sub-assembly.


This DTC is stored when the engine coolant temperature does not reach 75°C (167°F) despite sufficient engine warm-up time having elapsed.

DTC No. DTC Detection Condition Trouble Area
P0128

All of the following conditions are met for 5 seconds (2 trip detection logic):

(a) Cold start.

(b) The engine is warmed up.

(c) The engine coolant temperature is less than 75°C (167°F).


·

Water inlet with thermostat sub-assembly

·

Cooling system

·

Front exhaust pipe assembly

·

Engine coolant temperature sensor

·

ECM



MONITOR DESCRIPTION

A121605E23
4.861,2.289 5.253,2.563 false 4.455,2.563 6.104,2.904 1.649,0.341 10 Indicated Engine Coolant Temperature Reading 3.107,3.67 5.349,3.877 2.242,0.208 10 DTC Stored (after 2 Driving Cycles) 2.246,0.791 3.579,1.183 1.333,0.393 10 Estimated Engine Coolant Temperature 1.078,1.649 1.789,2.060 0.711,0.411 10 Threshold (75°C) 4.281,1.012 4.971,1.178 0.690,0.166 10 5 seconds 1.079,2.691 2.102,3.047 1.023,0.356 10 Engine Coolant Temperature 2.288,3.296 2.627,3.508 0.339,0.212 10 Time 3.835,2.069 3.719,0.875 3.719,0.875 3.579,0.875 false

The ECM estimates the engine coolant temperature based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction in the water inlet with thermostat sub-assembly or the engine cooling system and stores the DTC.

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A255184E11
0.75,1.26 1.375,1.51 0.625,0.25 10 false 80 km/h 0.177,1.604 1.25,2.01 1.073,0.406 10 false Power Switch on (IG) 1.771,1.49 2,1.646 0.229,0.156 10 false [A] 3.292,1.104 3.49,1.302 0.198,0.198 10 false [B] 4.802,2.948 5.031,3.177 0.229,0.229 10 false [C] 3.042,2.292 3.823,2.542 0.781,0.25 10 false 15 minutes 2.052,0.021 6.063,0.177 4.01,0.156 10 false - Engine coolant temperature when engine started: 56°C or less 2.052,0.354 5.635,0.5 3.583,0.146 10 false - Intake air temperature when engine started: 0 to 35°C 2.052,0.667 6.271,0.823 4.219,0.156 10 false - Heater set to MAX HOT with fresh air mode selected and A/C off 0.125,2.042 1.313,2.323 1.188,0.281 10 false Power Switch off

1.

Stop the engine and allow it to soak.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG) and turn the GTS on [A].

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp and Intake Air.

5.

Check that "Coolant Temp" is 56°C (133°F) or less and "Intake Air" is between 0 and 35°C (32 and 95°F).

6.

Set the heater to MAX HOT with fresh air mode selected and turn the A/C off.

7.

Start the engine and drive the vehicle at 80 km/h (50 mph) for 15 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

After "Coolant Temp" stabilizes, check that "Coolant Temp" is 75°C (167°F) or higher [C].

HINT:

If "Coolant Temp" is less than 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and water inlet with thermostat sub-assembly.



CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0128 is output A
DTC P0128 and other DTCs are output B

HINT:

If any DTCs other than P0128 are output, troubleshoot those DTCs first.




A

2.CHECK COOLING SYSTEM

B

2.CHECK COOLING SYSTEM
a.

Check for defects in the cooling system that might cause the system to be too cold, such as abnormal cooling fan operation or any modifications.



OK

3.INSPECT FRONT EXHAUST PIPE ASSEMBLY

NG

REPAIR OR REPLACE COOLING SYSTEM

3.INSPECT FRONT EXHAUST PIPE ASSEMBLY
a.

Inspect the front exhaust pipe assembly (exhaust flow control valve) operation.

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>EXHAUST HEAT RECIRCULATION SYSTEM>ON-VEHICLE INSPECTION



OK

4.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

NG

REPLACE FRONT EXHAUST PIPE ASSEMBLY

4.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).


Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>THERMOSTAT>INSPECTION


OK

5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

NG