88467
1.INSTALL NO. 1 COOLER CONDENSER CUSHION
Install the 4 No. 1 cooler condenser cushions to the cooler condenser assembly.
88460
2.INSTALL COOLER CONDENSER ASSEMBLY
Engage the 2 guides to install the cooler condenser assembly.
Do not damage the condenser or radiator when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the condenser as follows.
Add 40 cc (1.35 fl. oz.)
ND-OIL 11 or equivalent.
88706
3.CONNECT LIQUID PIPE SUB-ASSEMBLY
Remove the attached vinyl tape from the liquid pipe sub-assembly and the connecting part of the cooler condenser assembly.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the pipe joint.
ND-OIL 11 or equivalent.
Install the O-ring onto the liquid pipe sub-assembly.
Install the liquid pipe sub-assembly onto the cooler condenser assembly with the bolt.
88711
4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose and the connecting part of the cooler condenser assembly.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the hose joint.
ND-OIL 11 or equivalent.
Install the O-ring onto the No. 1 cooler refrigerant discharge hose.
Install the No. 1 cooler refrigerant discharge hose onto the cooler condenser assembly with the bolt.
16712
5.INSTALL NO. 2 FAN SHROUD
53205
6.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
53208A
7.INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY
Install the hood lock support sub-assembly with the 2 bolts.
Connect the connector.
53510
8.INSTALL HOOD LOCK ASSEMBLY
52131A
9.INSTALL FRONT BUMPER REINFORCEMENT (w/o Wheel Opening Moulding)
52131A
10.INSTALL FRONT BUMPER REINFORCEMENT (w/ Wheel Opening Moulding)
53936D
11.INSTALL FRONT END PANEL PROTECTOR LH (w/o Wheel Opening Moulding)
w/ Front Spoiler:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/o Wheel Opening Moulding)>REASSEMBLY
52611
12.INSTALL FRONT BUMPER ENERGY ABSORBER (w/o Wheel Opening Moulding)
52611
13.INSTALL FRONT BUMPER ENERGY ABSORBER (w/ Wheel Opening Moulding)
53288B
14.INSTALL RADIATOR SUPPORT EXTENSION LH (w/o Wheel Opening Moulding)
53288B
15.INSTALL RADIATOR SUPPORT EXTENSION LH (w/ Wheel Opening Moulding)
53287B
16.INSTALL RADIATOR SUPPORT EXTENSION RH (w/o Wheel Opening Moulding)
53287B
17.INSTALL RADIATOR SUPPORT EXTENSION RH (w/ Wheel Opening Moulding)
53286B
18.INSTALL NO. 2 RADIATOR SIDE AIR SEAL (w/o Wheel Opening Moulding)
53286B
19.INSTALL NO. 2 RADIATOR SIDE AIR SEAL (w/ Wheel Opening Moulding)
53285B
20.INSTALL NO. 1 RADIATOR SIDE AIR SEAL (w/o Wheel Opening Moulding)
53285B
21.INSTALL NO. 1 RADIATOR SIDE AIR SEAL (w/ Wheel Opening Moulding)
53289A
22.INSTALL RADIATOR SUPPORT OPENING COVER (w/o Wheel Opening Moulding)
53289A
23.INSTALL RADIATOR SUPPORT OPENING COVER (w/ Wheel Opening Moulding)
24.INSTALL FRONT BUMPER ASSEMBLY (w/o Wheel Opening Moulding)
25.INSTALL FRONT BUMPER ASSEMBLY (w/ Wheel Opening Moulding)
53301
26.INSPECT HOOD SUB-ASSEMBLY
53301
27.ADJUST HOOD SUB-ASSEMBLY
28.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
29.WARM UP COMPRESSOR
30.INSPECT FOR REFRIGERANT LEAK