Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2020.08
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM S

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DIAGNOSTIC TROUBLE CODE CHART  


HINT:

If any DTCs are displayed during the DTC check, inspect the circuit listed for those DTCs. For details of each DTC, refer to the page indicated in the DTC chart.


Power Steering System
DTC Code Detection Item Return-to-normal Condition EPS Warning Light See page
C1511/11 Torque Sensor 1 Malfunction Power switch on (IG) again *1 (Click here)
C1512/11 Torque Sensor 2 Malfunction Power switch on (IG) again *1 (Click here)
C1513/11 Torque Sensor Deviation Excessive Power switch on (IG) again *1 (Click here)
C1514/11 Torque Sensor Power Supply Voltage Malfunction Power switch on (IG) again *1 (Click here)
C1515/15 Torque Sensor Zero Point Adjustment is not Initialized Zero point calibration occurs *1 (Click here)
C1516/16 Torque Sensor Zero Point Adjustment Incomplete Clear DTC *1 (Click here)
C1517/11 Torque Hold Power switch on (IG) again *1 (Click here)
C1521/24 Short in Motor Circuit Power switch on (IG) again *1 (Click here)
C1522/24 Power Supply Sensor Power switch on (IG) again *1 (Click here)
C1523/24 Current Deviation Excessive Power switch on (IG) again *1 (Click here)
C1524/24 Motor Circuit Malfunction Power switch on (IG) again *1 (Click here)
C1525/17 Rotation Angle Sensor Initialization Undone Rotation angle sensor calibration occurs *1 (Click here)
C1526/18 Rotation Angle Sensor Initialization Incomplete Clear DTC *1 (Click here)
C1528/12 Motor Rotation Angle Sensor Malfunction Power switch on (IG) again *1 (Click here)
C1531/25 ECU Malfunction Power switch on (IG) again *1 (Click here)
C1532/25 ECU Malfunction Power switch on (IG) again *1 (Click here)
C1533/25 Temperature Sensor Circuit is Low or High After normal judgment *2 (Click here)
C1534/25 EEPROM Malfunction Power switch on (IG) again *3 (Click here)
C1541/13 Vehicle Speed Signal After normal judgment *1 (Click here)
C1551/25 IG Power Supply Voltage Malfunction Power switch on (IG) again or after normal confirmation *1 (Click here)
C1552/22 PIG Power Supply Voltage Malfunction Power switch on (IG) again or after normal confirmation *1 (Click here)
C1554/23 Power Supply Relay Failure Power switch on (IG) again *1 (Click here)
C1555/25 Motor Relay Welding Failure Power switch on (IG) again *1 (Click here)
C1581/26 Assist Map Number Un-Writing Assist map written *1 (Click here)
C1582/26 Assist Map Number Mismatch Power switch on (IG) again *1 (Click here)
U0129/42 Lost Communication with Brake System Control Module After normal confirmation *1 (Click here)
U023A/45*4 Lost Communication with Forward Recognition Camera After normal confirmation *1 (Click here)
U0293/41 Lost Communication with Hybrid Control Module After normal confirmation *1 (Click here)
U1105/46 Lost Communication with Parking Assist ECU Power switch on (IG) again or after normal confirmation *2 (Click here)

HINT:
·

*1: Warning light comes on

·

*2: Warning light turns off

·

*3: Torque sensor adjustment is set to the default value and control is continued. In this case, the warning light illuminates.

·

*4: w/ Forward Recognition Camera