Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › from 2016.08
RM3210E _58 Vehicle Interior _047504 INTERIOR PANELS / TRIM _0242035 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.

When installing a new lower instrument panel assembly, No. 1 instrument panel sub-assembly or lower instrument panel sub-assembly:

i.

Immediately before installing the lower instrument panel assembly, twist and cut off the portion as shown in the illustration.

B437311



b.

Install the lower instrument panel sub-assembly with the 2 bolts <A>, 4 bolts <B>, 3 screws <C> or <G> and screw <D>.

B433257C01
5.094,5.031 5.406,5.188 0.313,0.156 10 true *a 2.76,1.219 3.073,1.375 0.313,0.156 10 true *c 3.604,3.969 3.917,4.125 0.313,0.156 10 true *b 5.917,3.406 6.229,3.563 0.313,0.156 10 true *d 0.771,1.271 1.083,1.427 0.313,0.156 10 true *e 5.729,0.625 6.042,0.781 0.313,0.156 10 true *e 4.896,0.938 5.208,1.094 0.313,0.156 10 true *c 3.24,4.417 3.552,4.573 0.313,0.156 10 true *c 2,4.667 2.313,4.823 0.313,0.156 10 true *b 5.281,3.344 5.594,3.5 0.313,0.156 10 true *b 6.531,2.938 6.844,3.094 0.313,0.156 10 true *b 5.729,4.938 6.042,5.094 0.313,0.156 10 true *a
*a Bolt <A> *b Bolt <B>
*c Screw <C> or <G> *d Screw <D>
*e Clip - -


NOTICE:
·

Do not damage the lower instrument panel sub-assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.

·

If a screw <C> is loose and cannot be installed securely, replace it with a screw <G>.



Torque:
Bolt <A> : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt <B> : 13 N*m (133 kgf*cm, 10 ft.*lbf)


c.

Install the 2 clips.


d.

Engage each clamp.

B433255C02
5.26,4.583 5.563,4.771 0.302,0.188 12 true *B 5.583,0.396 5.896,0.615 0.313,0.219 12 true *A
*A w/ Digital Audio Broadcasting Antenna or Television Antenna *B w/ Telematics Transceiver



e.

Connect each connector.


f.
E337576C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to connect the cooler (room temp. sensor) thermistor as shown in the illustration.


g.

Engage the 4 clips and 2 claws to connect the lower instrument cover sub-assembly to the upper steering column cover.


Hide 81260 3.INSTALL GLOVE BOX LIGHT ASSEMBLY

Hide 55660 4.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B433297C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 clips to install the No. 2 instrument panel register assembly as shown in the illustration.


Hide 55650 5.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B433249C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 clips to install the No. 1 instrument panel register assembly as shown in the illustration.


Hide 55433B 6.INSTALL NO. 2 LOWER INSTRUMENT PANEL FINISH PANEL

a.
B433230C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 9 clips to install the No. 2 lower instrument panel finish panel as shown in the illustration.


Hide 58848B 7.INSTALL SHIFT LEVER HOLE COVER

a.

Connect each connector


b.
B433222C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 5 clips to install the shift lever hole cover as shown in the illustration.


c.

Engage the clamp.


Hide 55406B 8.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

Connect each connector


b.

Engage each clamp.


c.
B433211C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 5 clips to install the lower center instrument cluster finish panel sub-assembly as shown in the illustration.


Hide 55054 9.INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.

Engage the claw to install the glove compartment door stopper sub-assembly.


Hide 55550 10.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

a.

Hold the glove compartment door assembly at an angle approximately 64.2° from its closed position and engage the 2 hinges horizontally as shown in the illustration.

B437333C01
4.042,1.25 4.354,1.406 0.313,0.156 10 false *a
*a 64.2° - -
V113147

Install in this Direction - -


NOTICE:

Engaging the hinges from an upward angle will deform the hinges. Be sure to install the glove compartment door assembly horizontally.



b.
B433198C02
3.125,3.073 3.063,2.854 true 3.063,3.094 3.344,3.26 0.281,0.167 10 true *1 3.01,1.51 3.167,1.708 0.156,0.198 10 true A 0.469,1.26 0.625,1.458 0.156,0.198 10 true B
*1 Glove Compartment Door Stopper Sub-assembly


Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows shown in the illustration and engage the stoppers to install the glove compartment door assembly.


c.

Engage the claw to connect the glove compartment door stopper sub-assembly.


Hide 55607 11.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.

Connect the connector.


b.
B433196C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration.


c.
B433194C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.


Hide 62111C 12.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67913 13.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 14.INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

a.

Engage the clamp.


b.

Engage the 2 guides.


c.

Install the radio tuner opening cover with bracket with the 4 bolts <B>.


Hide 15.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 16.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)

Hide 55405B 17.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

Engage the clamp.


b.

Connect each connector.


c.

Engage the 5 guides and 18 clips to install the center instrument cluster finish panel sub-assembly as shown in the illustration.

B433171C01
0,0 0,0 false
V113147

Install in this Direction - -



d.

for LHD:

i.

Install the clip.



Hide 55435A 18.INSTALL INSTRUMENT PANEL FINISH PANEL END RH

a.

w/ Airbag Cut Off Switch:

i.

Connect the connector.



b.
B442267C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 guides as shown in the illustration.


c.
B442268C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 6 clips to install the instrument panel finish panel end RH as shown in the illustration.


Hide 19.INSTALL COMBINATION METER ASSEMBLY

Hide 73900 20.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55480D 21.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.

Connect the connector.


b.
B433153C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 6 clips as shown in the illustration.


c.

Install the lower instrument panel finish panel assembly with the screw <C>.


Hide 53601 22.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.


Hide 55606 23.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.

for RHD:

i.

Engage the 2 claws to connect the DLC3 connector.


ii.

Engage the clamp.



b.

Connect the connector.


c.
B433143C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


d.
B433141C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


e.

Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <F>.


Hide 62112 24.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914 25.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 55470 26.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

a.

Connect each connector.


b.
B432302C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and 4 clips to install the instrument cluster finish panel garnish assembly as shown in the illustration.


Hide 55436A 27.INSTALL INSTRUMENT PANEL FINISH PANEL END LH

a.
B432298C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 guides as shown in the illustration.


b.
B432294C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 6 clips to install the instrument panel finish panel end LH as shown in the illustration.


Hide 58910C 28.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 29.INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

Hide 30.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION