ECD SYSTEM (for DPF) > Lack of Power or Hesitation |
| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|
|
|
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Component | Mass air flow meter | |
| Main fault | Decrease in performance (foreign matter is stuck) | |
| Symptoms | Lack of power, black smoke | |
| Data List | MAF | |
| ||
| Component | Intake system | |
| Symptom: Main fault |
| |
| Data List |
| |
| Component | Turbocharger system | |
| Main fault |
| |
| Symptoms | Lack of power (when vehicle starting, when heavy load) (Black smoke is not emitted when racing while vehicle stopped) | |
| Data List | MAP (inside intake air pressure), Target Booster Pressure
| |
| Component | Exhaust system | |
| Main fault | Blockage | |
| Symptoms | Lack of power (high engine speed, when heavy load) | |
| Data List | MAP (inside intake air pressure), Target Booster Pressure When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt. | |
| Component | Glow system | |
| Main fault | Open circuit, glow plug relay fault | |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) | |
| Data List | Check the glow plug indicator light | |
| Diagnostic Point | Try to measure the resistance of the glow plug | |
| Component | Engine | |
| Main fault | Damaged, seized up | |
| Symptoms | Cannot crank, crank speed is low, strange noise | |
| Component | Engine | |
| Main fault | Loss of compression | |
| Symptoms | Rough idle (lack of power always) | |
| Data List | Engine Speed of Cyl#
| |
Diesel Injection
| Component | Fuel supply pump | |
| Main fault | - | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
| |
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. | |
| Component | Fuel filter | |
| Main fault | Blockage | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. | |
| Component | Fuel injector | |
| Main fault | Blockage | |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Injection Feedback Val
| |
| Component | Pressure discharge valve | |
| Main fault | Does not completely close | |
| Symptoms | Difficult to start, engine stall, rough idle, lack of power | |
| Component | Injector Driver (EDU) | |
| Main fault | Circuit fault: The fuel injector does not open. | |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Same as fuel injector | |
| Diagnostic Trouble Code | When the EDU has a fault, some DTCs may be stored. | |
| Component | Fuel pressure sensor | |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) | |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Code | When the fuel pressure sensor has a fault, some DTCs may be stored. | |
| Component | Irregular fuel | |
| Main fault | - | |
| Symptoms | Difficult to start, rough idle (especially when cold) | |
Diesel EGR
| Component | EGR system | |
| Main fault |
| |
| Symptoms |
| |
| Data List | Actual EGR Valve Pos., Target EGR Position
| |
Diesel Throttle
| Component | Diesel throttle system | |
| Main fault | Stuck, does not move smoothly | |
| Symptoms |
| |
| Data List |
| |
| Data List Related to Lack of Power |
Engine Control
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Engine Speed | Idling: 750 to 850 rpm | Crankshaft position sensor | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. |
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| MAP | MAP (inside intake air pressure)
|
|
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| MAF | - |
|
|
Results of real-vehicle check:
| |||
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Intake Air | After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal. | Intake air temperature sensor | If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. |
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Coolant Temp |
| Engine coolant temperature sensor | If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. |
Diesel Injection
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Target Common Rail Pressure | - | - |
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Fuel Press |
|
|
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Target Pump SCV Current |
| With this data, component fault not specified, use this data as a reference |
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Injection Feedback Val #1 (to #4) | Injection Feedback Val:
|
| With Injection Feedback Val, find the malfunctioning cylinders. However, before replacing the injector, identify the malfunctioning cylinders with a power balance test. |
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Injection Volume |
| All cylinders | - |
Results of real-vehicle check:
| |||
Diesel Throttle
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Actual Throttle Position |
| Throttle valve | Actual Throttle Position is the closing percentage of the throttle valve.
|
Results of real-vehicle check:
| |||
Diesel EGR
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Target EGR Position | - | - |
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Actual EGR Valve Pos. | Generally Actual EGR Valve Pos. = Target EGR Position +/-5% (completely closed = 0%, completely open = 100%). The EGR valve Active Test can be used to check whether Actual EGR Valve Pos. = Target EGR Position (take into consideration the temperature of the intake air and the coolant temperature when the malfunction occurs). Sometimes the malfunction only occurs around a certain temperature. Take into consideration the temperature of the intake air and the coolant temperature when the malfunction occurs. | EGR valve | Inspect while comparing to "Target EGR Position". |
Results of real-vehicle check:
| |||
| Actual Examples of Malfunction |
Lack of power caused by overly low boost pressure

Lack of power caused by overly low MAF

EGR valve stuck in open position

| Explanation of Symptom |
| Lack of Power | The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air. The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector is open for. Basically, the fuel pressure is controlled to reach the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure. The manifold absolute pressure is controlled to reach the Target Booster Pressure. Also, when accelerating the vehicle at full throttle, the throttle is fully open and the EGR valve is fully closed, preserving the mass air flow. |
| Trouble Area Chart According to Problem Cause |


| 1.READ OUTPUT DTC (RELATED TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 2.TAKE SNAPSHOT DURING LACK OF POWER |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
![]() ![]() ![]() ![]() ![]() |
Take a snapshot of the following Data List items with the intelligent tester during lack of power.
| Data List | Value | Unit |
| Vehicle Speed | 44 | km/h |
| Engine Speed | 3500 | rpm |
| Accel Position | 99.60 | % |
| Target Booster Pressure | 234.19 | kPa |
| MAP | 227 | kPa |
| MAF | 140.96 | g/sec |
| Calculate Load | 100 | % |
| Target Common Rail Pressure | 194350 | kPa |
| Fuel Press | 189820 | kPa |
| Target Pump SCV Current | 1402.8 | mA |
| Injection Volume | 70.52 | mm3/st |
| VN Turbo Command | 44 | % |
| Actual EGR Valve Pos. | 0 | % |
| Actual Throttle Position | 0 | % |
| AF Lambda B1S1 | 1.167 | - |
| AFS Voltage B1S1 | 0.27 | V |
| Data List | Value | Unit |
| Engine Speed | 771 | rpm |
| Target Booster Pressure | 92.69 | kPa |
| MAP | 94 | kPa |
| MAF | 3.87 | g/sec |
| Target Common Rail Pressure | 35000 | kPa |
| Fuel Press | 33640 | kPa |
| Injection Volume | 5.15 | mm3/st |
| VN Turbo Command | 57 | % |
| Actual EGR Valve Pos. | 54.1 | % |
| Target EGR Position | 54.1 | % |
| Actual Throttle Position | 93 | % |
| Accel Position | 0.00 | % |
| Injection Feedback Val #1 | 0.0 | mm3/st |
| Injection Feedback Val #2 | -0.5 | mm3/st |
| Injection Feedback Val #3 | 0.0 | mm3/st |
| Injection Feedback Val #4 | 0.1 | mm3/st |
| Atmosphere Pressure | 100 | kPa |
| Coolant Temp | 76 | °C |
| NEXT | |
| 3.CHECK SNAPSHOT |
![]() |
Check the condition of the vehicle using the snapshot taken during the lack of power.
| Result | Proceed to |
| Fuel Press is less than "Target Common Rail Pressure - 20000 kPa" when accelerating with accelerator fully open | B |
| Target Pump SCV Current 3000 mA or more | C |
| One of the Injection Feedback Val #1 to 4 values is outside the range of +/-3 mm3/st when idling after warm up | D |
| Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st when idling after warm up | E |
| None of the conditions below apply | A |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.CHECK SNAPSHOT |
![]() ![]() |
Check the condition of the vehicle using the snapshot taken during the lack of power.
| Result | Proceed to |
| MAP is less than "Target Booster Pressure - 20 kPa" (MAF is normal) when accelerating with accelerator fully open | A |
MAF is low when accelerating with accelerator fully open (MAP is normal)
| B |
| MAP and MAF are both low when accelerating with the accelerator fully open | C |
| None of the above conditions apply | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 5.INSPECT VACUUM HOSE |
Check the vacuum hose connection (manifold absolute pressure sensor).
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERE PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is ON (engine stopped).
| Result | Proceed to |
| Atmosphere Pressure is different from actual atmospheric pressure | A |
| MAP is different from actual atmospheric pressure | B |
| MAP and Atmosphere Pressure have the same value | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 7.CHECK MASS AIR FLOW METER |
Check the mass air flow meter (Click here).
|
| ||||
| OK | |
| 8.CHECK EGR VALVE ASSEMBLY |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Close Lrn. Status.
Read the values.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.
Remove the EGR valve assembly (Click here).
Visually check the electric EGR control valve for deposits.
If there are deposits, clean the electric EGR control valve.
![]() |
Hold the electric EGR control valve up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.
|
| ||||
| OK | |
| 9.READ VALUE USING INTELLIGENT TESTER (ACCEL POSITION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.
Read the value.
| Condition | Standard Value |
| Accelerator pedal released | 0% |
| Accelerator pedal depressed | 95% or more |
Accelerator pedal released → depressed
| 0 to 95% or more |
|
| ||||
| OK | |
| 10.CHECK DIESEL THROTTLE BODY ASSEMBLY |
Check the diesel throttle body assembly (Click here).
|
| ||||
| OK | |
| 11.CHECK INTAKE SYSTEM |
Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.
|
| ||||
| OK | |
| 12.INSPECT TURBOCHARGER SUB-ASSEMBLY |
Inspect the turbocharger sub-assembly .
|
| ||||
| OK | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the lack of power has been successfully repaired.
|
| ||||
| OK | ||
| ||
| 14.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.
![]() |
Take a snapshot with the intelligent tester during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

| Result | Proceed to |
| Difference between target fuel pressure and actual fuel pressure is less than 10000 kPa | A |
| Difference between target fuel pressure and actual fuel pressure is 10000 kPa or more | B |
|
| ||||
| A | ||
| ||
| 16.INSPECT COMMON RAIL ASSEMBLY |
Inspect the common rail assembly .
|
| ||||
|
| ||||
| 17.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
![]() |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) - B32-41 (PCV+) | Always | Below 1 Ω |
| B46-2 (PCV) - B32-81 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) or B32-41 (PCV+) - Body ground | Always | 10 kΩ or higher |
| B46-2 (PCV) or B32-81 (PCV-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Suction Control Valve) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 18.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the fuel supply pump.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump.
|
| ||||
| OK | |
| 19.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
| NEXT | |
| 20.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 21.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the lack of power has been successfully repaired.
| NEXT | ||
| ||
| 23.READ VALUE USING INTELLIGENT TESTER (CATALYST DIFFERENTIAL PRESS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press.
Check the differential pressure at an engine speed of 3000 rpm with no load.
With the vehicle stopped, fully depress the accelerator pedal for 5 seconds and then release it.*A
Repeat procedure *A 10 times.*B
Check for black smoke emission during the above procedures *A and *B.
| Differential Pressure (kPa) | Proceed to | Note |
| Catalyst Differential Press 0.25 or more at 3000 rpm (No engine load) | B | An extremely large amount of PM (Particulate Matter) has accumulated in the DPF catalyst. |
| Black smoke is emitted 5 times or more | B | The DPF catalyst cannot trap PM because it is melted or cracked, and therefore must be replaced. Also, if a piece of the catalyst breaks off, due to melting or another condition, and enters the exhaust pipe downstream, the exhaust pipe could be blocked, possibly causing a different malfunction. Therefore, when replacing the DPF catalyst, visually inspect the rear surface of the DPF filter substrate to determine if replacement of the exhaust pipe is necessary. |
| Except above | A | - |
| Condition | Differential Pressure Output |
| Ignition switch ON | Approximately 0 kPa |
|
| ||||
| A | |
| 24.CHECK TEMPERATURE WHEN LACK OF POWER OCCURS |
Check the temperature when the lack of power occurs.
| Result | Proceed to |
| Poor acceleration only when engine is cold | A |
| Poor acceleration when engine is cold and warm | B |
|
| ||||
| A | |
| 25.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 26.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE) |
Inspect the glow plug assembly .
|
| ||||
| OK | |
| 27.INSPECT INJECTOR COMPENSATION CODE |
Read the injector compensation codes .
|
| ||||
| OK | |
| 28.CHECK FUEL QUALITY |
Check that fuel with a low cetane number is used.
| NEXT | |
| 29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the lack of power has been successfully repaired by starting the engine.
| NEXT | ||
| ||
| 30.INSPECT INJECTOR COMPENSATION CODE |
Read the injector compensation codes .
|
| ||||
| OK | |
| 31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
| NEXT | |
| 32.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
|
| ||||
|
| ||||
| 33.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 34.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER |
Replace the fuel injector of the malfunctioning cylinder (Click here).
| NEXT | |
| 35.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 36.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the fuel injector pilot quantity learning .
| NEXT | |
| 37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 38.CHECK INTAKE SYSTEM DEPOSIT |
Check carbon is accumulating on the intake manifold, cylinder head, etc. and if so, clean it off.
| NEXT | |
| 39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 40.REPLACE FUEL INJECTORS OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
| NEXT | |
| 41.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 42.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation codes .
Perform registration of the fuel injector pilot quantity learning values .
| NEXT | |
| 43.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 44.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and replace clogged the fuel pipe.
| NEXT | |
| 45.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 46.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 47.REPLACE COMMON RAIL |
Replace the common rail (Click here).
| NEXT | |
| 48.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 49.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||