There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Lane Departure Alert System *3: w/ Stop and Start System *4: for Radio and Display Type *5: for Navigation Receiver Type *6: for 4WD/AWD *7: w/ Entry and Start System *8: w/ Vehicle Stability Control System |
|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
ECM ·
Blind spot monitor sensor LH*1 ·
Brake actuator assembly (skid control ECU) ·
Power steering ECU assembly ·
Main body ECU (multiplex network body ECU) ·
Lane departure warning camera*2 ·
Air conditioning amplifier assembly ·
Engine stop and start ECU*3 ·
Radio and display receiver assembly*4 ·
Navigation ECU sub-assembly*5 ·
4WD ECU assembly*6 ·
Certification ECU (smart key ECU assembly)*7 ·
Spiral with sensor cable sub-assembly (steering angle sensor)*8 ·
Airbag sensor assembly ·
Combination meter assembly ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
No. 3 CAN junction connector ·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
For vehicles with an entry and start system:
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION
w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>PRECAUTION
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the G124 No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G14-14 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect wire harness No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the N28 No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G14-14 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 3 CAN junction connectors.
| *1 | No. 3 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Blind Spot Monitor System |
|||
| N27 | Y | W | ECM |
| N29 | R | W | Blind Spot Monitor Sensor LH* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N27-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N27-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N29-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N29-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG (to ECM CAN main wire) |
| NG (to blind spot monitor sensor LH CAN branch wire) |
OK
NG (to ECM CAN main wire)
NG (to blind spot monitor sensor LH CAN branch wire)
Reconnect all wire harness No. 3 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the ECM connector.
| *A | for 2AR-FE, 3ZR-FAE, 3ZR-FE | *B | for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF |
| *a | Front view of wire harness connector
(to ECM) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-13 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A62-26 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-7 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A61-6 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 1AD-FTV: Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-CCo, 2AD-DPF: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
NG
Reconnect all wire harness No. 3 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
| *b | Front view of DLC3 |
Disconnect the blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R1-2 (CA1P) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R1-7 (CA1N) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect wire harness No. 3 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| G118 | L | W | No. 3 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G118-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G118-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect wire harness No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the G129 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G14-14 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 CAN junction connectors.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: for Radio and Display Type *2: for Navigation Receiver Type *3: for 4WD/AWD *4: w/ Entry and Start System *5: w/ Stop and Start System |
|||
| G128 | G | W | Combination Meter Assembly |
| G130 | Y | W | ·
Radio and Display Receiver Assembly*1 ·
Navigation ECU Sub-assembly*2 |
| G131 | L | W | 4WD ECU Assembly*3 |
| G132 | R | W | Certification ECU (Smart Key ECU Assembly)*4 |
| G133 | BR | W | Airbag Sensor Assembly |
| G153 | B | W | Air Conditioning Amplifier Assembly |
| G154 | LG | W | Engine Stop and Start ECU*5 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G128-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G130-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G130-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G131-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G131-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G132-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G132-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G133-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G133-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G153-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G153-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G154-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G154-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to air conditioning amplifier assembly CAN branch wire) | B |
| NG (to engine stop and start ECU CAN branch wire) | C |
| NG (to combination meter assembly CAN main wire) | D |
| NG (to radio and display receiver assembly [for Radio and Display Type] or navigation ECU sub-assembly [for Navigation Receiver Type] CAN branch wire) | E |
| NG (to 4WD ECU assembly CAN branch wire) | F |
| NG (to certification ECU [smart key ECU assembly] CAN branch wire) | G |
| NG (to airbag sensor assembly CAN branch wire) | H |
A
B
C
D
E
F
G
H
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the air conditioning amplifier assembly connector.
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G81-11 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G81-12 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-8 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G80-9 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Engine Stop and Start ECU) |
| *b | Front view of DLC3 |
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G87-15 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G87-16 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-32 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G16-31 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
Check for vehicle types.
| Proceed to |
|---|
| for Radio and Display Type |
| for Navigation Receiver Type |
for Radio and Display Type
for Navigation Receiver Type
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of DLC3 |
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G143-9 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G143-10 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation ECU Sub-assembly) |
| *b | Front view of DLC3 |
Disconnect the navigation ECU sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G139-9 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G48-10 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to 4WD ECU Assembly) |
| *b | Front view of DLC3 |
Disconnect the 4WD ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G86-6 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G86-5 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
| *b | Front view of DLC3 |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G84-14 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G84-15 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G92-13 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G92-22 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect wire harness No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connectors.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: w/ Vehicle Stability Control System *2: w/ Lane Departure Alert System |
|||
| G119 | V | W | No. 2 CAN Junction Connector |
| G120 | R | W | Brake Actuator Assembly (Skid Control ECU) |
| G121 | LG | W | Power Steering ECU Assembly |
| G122 | P | W | Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*1 |
| G123 | Y | W | Main Body ECU (Multiplex Network Body ECU) |
| G125 | G | W | Lane Departure Warning Camera*2 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G119-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G119-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G120-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G120-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G121-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G121-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G122-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G122-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G123-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G123-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G125-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G125-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to brake actuator assembly [skid control ECU] CAN branch wire) | B |
| NG (to power steering ECU assembly CAN branch wire) | C |
| NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) | D |
| NG (to main body ECU [multiplex network body ECU] CAN branch wire) | E |
| NG (to lane departure warning camera CAN branch wire) | F |
| NG (to No. 2 CAN junction connector CAN main wire) | G |
A
B
C
D
E
F
G
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | w/ Vehicle Stability Control System |
| *B | w/o Vehicle Stability Control System |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
| *b | Front view of DLC3 |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-25 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A64-14 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-25 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A63-14 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
w/ Vehicle Stability Control System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL
w/o Vehicle Stability Control System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
| *b | Front view of DLC3 |
Disconnect the power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h1-4 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| h1-8 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
| *b | Front view of DLC3 |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G12-3 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G12-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
| *b | Front view of DLC3 |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G78-14 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G78-13 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Lane Departure Warning Camera) |
| *b | Front view of DLC3 |
Disconnect the lane departure warning camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q13-6 (CA1P) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q13-12 (CA1N) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG