Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Receiver Gauge Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using the CAN communication line. The combination meter assembly displays the engine coolant temperature, which is calculated based on the data received from the ECM.

WIRING DIAGRAM

E200122E17
1.615,2.667 1.948,2.833 0.333,0.167 10 ECM 4.49,2.75 6.333,2.917 1.844,0.167 10 Combination Meter Assembly 0.802,3.365 2.521,3.563 1.719,0.198 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
CAN communication system DTC is not output
CAN communication system DTC is output (for LHD)
CAN communication system DTC is output (for RHD)



CAN communication system DTC is not output

2.CHECK SFI SYSTEM OR ECD SYSTEM

CAN communication system DTC is output (for LHD)

CAN communication system DTC is output (for RHD)

2.CHECK SFI SYSTEM OR ECD SYSTEM

*1: Engine Type Gasoline

*2: Engine Type Diesel


a.

Check if a SFI system*1 or ECD system*2 DTC is output.

ECD system (1AD-FTV):

ECD system (2AD-FHV):

ECD system (2AD-FTV [for CCo]):

ECD system (2AD-FTV [for DPF]): Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

SFI system (2AR-FE): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

SFI system (3ZR-FAE): Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

SFI system (3ZF-FE): Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
DTC is not output (for Segment Display Type)
DTC is not output (for Dot Display Type)
ECD system DTC is output (1AD-FTV)
ECD system DTC is output (2AD-FHV)
ECD system DTC is output (2AD-FTV [for CCo])
ECD system DTC is output (2AD-FTV [for DPF])
SFI system DTC is output (2AR-FE)
SFI system DTC is output (3ZR-FAE)
SFI system DTC is output (3ZR-FE)



DTC is not output (for Segment Display Type)

3.PERFORM ACTIVE TEST USING GTS (WATER TEMPERATURE METER OPERATION)

DTC is not output (for Dot Display Type)

4.READ VALUE USING GTS (COOLANT TEMPERATURE, COOLANT TEMP)

ECD system DTC is output (1AD-FTV)

ECD system DTC is output (2AD-FHV)

ECD system DTC is output (2AD-FTV [for CCo])

ECD system DTC is output (2AD-FTV [for DPF])

SFI system DTC is output (2AR-FE)

SFI system DTC is output (3ZR-FAE)

SFI system DTC is output (3ZR-FE)

3.PERFORM ACTIVE TEST USING GTS (WATER TEMPERATURE METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Water Temperature Meter Operation Engine coolant temperature receiver gauge OFF, LOW, NORMAL or HIGH -
Body Electrical > Combination Meter > Active Test
Tester Display
Water Temperature Meter Operation
50004 122 89
OK:

Engine coolant temperature receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COOLANT TEMPERATURE, COOLANT TEMP)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS (COOLANT TEMPERATURE, COOLANT TEMP)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature 0 to 127.5°C (0 to 261.5°F) After warming up: 75 to 100°C (167 to 212°F) -
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max: 215°C (419°F) 60 to 90°C (140 to 194°F): After warming up engine -
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max: 140°C (284°F) 60 to 90°C (140 to 194°F): After warming up engine -
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10
Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8
Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.




Result:
Proceed to
The Data List values of the ECUs do not match.
The Data List values of the ECUs match.



The Data List values of the ECUs do not match.

REPLACE COMBINATION METER ASSEMBLY

The Data List values of the ECUs match.

5.CHECK COMBINATION METER ASSEMBLY
5.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Check that the operation of the engine coolant temperature receiver gauge returns to normal.

OK:

The operation of the engine coolant temperature receiver gauge returns to normal.



Result:
Proceed to
OK
NG (1AD-FTV)
NG (2AD-FHV)
NG (2AD-FTV)
NG (2AR-FE)
NG (3ZR-FAE)
NG (3ZR-FE)



OK

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

NG (1AD-FTV)

NG (2AD-FHV)

NG (2AD-FTV)

NG (2AR-FE)

NG (3ZR-FAE)

NG (3ZR-FE)