As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.
1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL
12611
6.REMOVE NO. 1 ENGINE COVER
Detach the 4 clips and remove the No. 1 engine cover.
Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover to break.
51441
7.REMOVE NO. 1 ENGINE UNDER COVER
Remove the 4 bolts and 2 screws.
Remove the 10 clips and No. 1 engine under cover.
50819
8.REMOVE FRONT FLOOR COVER
51442
9.REMOVE NO. 2 ENGINE UNDER COVER
Remove the bolt, clip and No. 2 engine under cover.
58165C
10.REMOVE FRONT FLOOR COVER RH
Loosen the 3 nuts and remove the 3 clips and front floor cover RH.
51443
11.REMOVE REAR ENGINE UNDER COVER RH
51444
12.REMOVE REAR ENGINE UNDER COVER LH
Remove the 2 clips and rear engine under cover LH.
13.DRAIN ENGINE COOLANT
14.DRAIN ENGINE OIL
15.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
16.DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
17.DRAIN TRANSFER OIL
52119A
18.REMOVE FRONT BUMPER COVER (for Automatic Transaxle)
17410
19.REMOVE FRONT EXHAUST PIPE ASSEMBLY
37100
20.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
89480A
21.REMOVE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
74404A
22.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Remove the bolt and loosen the nut.
Detach the 2 wire harness clamps.
Detach the hook of the battery clamp sub-assembly from the front battery bracket, and then remove the battery clamp sub-assembly.
28899
23.REMOVE BATTERY INSULATOR
28800
24.REMOVE BATTERY
74431
25.REMOVE BATTERY TRAY
74411B
26.REMOVE FRONT BATTERY BRACKET
Detach the 2 wire harness clamps.
Remove the 4 bolts and front battery bracket.
74414B
27.REMOVE BATTERY BRACKET REINFORCEMENT
Remove the 2 bolts and battery bracket reinforcement.
16400
28.REMOVE RADIATOR ASSEMBLY (for Automatic Transaxle)
25770A
29.DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY
17343D
30.REMOVE NO. 3 AIR HOSE
17705
31.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Disconnect the PCV hose.
Loosen the hose clamp and disconnect the air cleaner hose.
Disconnect the mass air flow meter connector and wire harness clamp.
Detach the 3 clips and remove the air cleaner cap sub-assembly.
17801
32.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
33.REMOVE AIR CLEANER CASE
Remove the 3 bolts and air cleaner case.
17769
34.REMOVE AIR CLEANER SUPPORT
Remove the 2 nuts and air cleaner support.
35.REMOVE FUEL FILTER ASSEMBLY
Slide the 2 clips and disconnect the 2 fuel hoses.
Remove the bolt and fuel filter assembly.
17119A
36.REMOVE AIR CLEANER BRACKET
Disconnect the glow plug relay and level warning switch connector.
Detach the 3 wire harness clamps.
Disconnect the 2 fuel hoses from the air cleaner bracket.
Remove the 3 bolts and air cleaner bracket.
89661
37.REMOVE ECM
38.DISCONNECT HOSES AND CONNECTORS
Remove the engine room relay block and junction block cover.
Disconnect the 3 connectors from the engine room No. 1 relay block.
Remove the nut.
Detach the 2 claws and disconnect the engine wire.
Remove the bolt and disconnect the engine wire cover clamp and engine wire harness clamp.
Remove the nut and disconnect the starter wire.
| *A | for Manual Transaxle |
| *B | for Automatic Transaxle |
Remove the bolt from the wire harness clamp bracket.
for Manual Transaxle:
Detach the clamp, remove the bolt and disconnect the ground cable from the manual transaxle assembly.
for Manual Transaxle:
Detach the wire harness clamp and disconnect the 2 connectors.
for Manual Transaxle:
Remove the bolt and disconnect the wire harness from the manual transaxle assembly.
for Automatic Transaxle:
Disconnect the transaxle ECM connector and detach the 2 wire harness clamps.
for Automatic Transaxle:
Remove the bolt and disconnect the ground cable from the automatic transaxle.
for Automatic Transaxle:
Detach the 2 clamps and disconnect the transaxle shift position switch connector.
Detach the 3 wire harness clamps from the 3 wire harness brackets.
for DPF:
Detach the 2 wire harness clamps and disconnect the 4 injector driver connectors.
for DPF:
Remove the 2 nuts and injector driver assembly.
for CCo:
Detach the wire harness clamp and disconnect the 4 injector driver connectors.
for CCo:
Remove the 2 nuts and injector driver assembly.
Slide the clip and disconnect the vacuum pump hose from the vacuum pump assembly.
87246A
39.DISCONNECT INLET HEATER WATER HOSE
Slide the clamp and disconnect the inlet heater water hose from the cylinder head sub-assembly.
87246A
40.DISCONNECT OUTLET HEATER WATER HOSE
Slide the clamp and disconnect the outlet heater water hose from the No. 3 water by-pass pipe.
16057
41.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY
Slide the clamp and disconnect the radiator hose sub-assembly from the cylinder head sub-assembly.
17342F
42.REMOVE INTERCOOLER AIR HOSE
16264D
43.DISCONNECT NO. 2 WATER BY-PASS HOSE
Slide the clamp and disconnect the No. 2 water by-pass hose from the No. 4 water by-pass pipe.
16572D
44.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clamp and disconnect the No. 2 radiator hose from the water inlet housing.
16470
45.REMOVE RADIATOR RESERVOIR ASSEMBLY
Slide the clamp and disconnect the water by-pass hose from the radiator reservoir assembly.
Remove the 2 bolts and radiator reservoir assembly.
88703
46.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
Remove the bolt and disconnect the discharge hose sub-assembly.
Remove the O-ring from the discharge hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
Disconnect the cooler compressor connector.
88704
47.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the bolt and disconnect the suction hose sub-assembly.
Remove the O-ring from the suction hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
33820B
48.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Remove the 2 pins.
Remove the 2 clips and disconnect the 2 transmission control cable assembly from the transmission control cable bracket.
33820B
49.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)
Remove the nut and clip, and disconnect the transmission control cable assembly from the transmission control cable bracket.
31470
50.DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)
Remove the 4 bolts and disconnect the clutch release cylinder assembly and clutch flexible hose bracket.
45259A
51.REMOVE COLUMN HOLE COVER SILENCER SHEET
52.SECURE STEERING WHEEL
45260
53.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
54.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
43502H
55.REMOVE FRONT AXLE SHAFT NUT LH
43501H
56.REMOVE FRONT AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
57.DISCONNECT FRONT SPEED SENSOR LH
58.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
59.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
60.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
45047
61.DISCONNECT TIE ROD END SUB-ASSEMBLY LH
45046
62.DISCONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
63.REMOVE FRONT AXLE ASSEMBLY LH
64.REMOVE FRONT AXLE ASSEMBLY RH
Perform the same procedure as for the LH side.
43420
65.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
43410
66.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
51218A
67.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH
Remove the 4 bolts and front suspension member reinforcement LH.
51217A
68.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
32101A
69.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for Automatic Transaxle)
23292D
70.REMOVE FUEL HOSE PROTECTOR
Remove the fuel hose protector from the cylinder head sub-assembly.
71.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-26040 |
| No. 2 Engine Hanger | 12282-26010 |
| Bolt | 91552-81025 or 90105-W0042 |
Insert the claw of the No. 1 engine hanger into the hole of the cylinder head sub-assembly.
Fit the fork part of the No. 2 engine hanger onto the rib of the cylinder head sub-assembly.
72.REMOVE ENGINE WITH TRANSAXLE
Remove the 6 bolts and disconnect the front crossmember sub-assembly.
Remove the through bolt, nut and front engine mounting insulator.
Set an engine lifter underneath the engine.
Place the engine on wooden blocks or equivalent so that the engine is level.
Remove the 2 bolts and 2 nuts and disconnect the engine mounting insulator sub-assembly RH.
Remove the bolt and nut and disconnect the engine mounting insulator LH.
Remove the 6 bolts, front suspension member rear brace RH and front suspension member rear brace LH.
Remove the 2 bolts and front suspension member sub-assembly.
Carefully remove the engine with transaxle from the vehicle.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
Attach an engine sling device and hang the engine with a chain block.
Remove the through bolt and disconnect the rear engine mounting insulator.
17361J
73.REMOVE NO. 1 AIR TUBE
| *A | for Manual Transaxle |
| *B | for Automatic Transaxle |
Loosen the hose clamp, and remove the 2 bolts and No. 1 air tube.
28100
74.REMOVE STARTER ASSEMBLY
82121
75.REMOVE ENGINE WIRE
12311A
76.REMOVE FRONT ENGINE MOUNTING BRACKET
for Manual Transaxle:
Remove the 3 bolts and front engine mounting bracket.
for Automatic Transaxle:
Remove the 4 bolts and front engine mounting bracket.
12321A
77.REMOVE REAR ENGINE MOUNTING BRACKET
Remove the 4 bolts and rear engine mounting bracket.
12325A
78.REMOVE ENGINE MOUNTING BRACKET LH
Perform this procedure only when replacement of the engine mounting bracket LH is necessary.
| *A | for Manual Transaxle |
| *B | for Automatic Transaxle |
Remove the 4 bolts and engine mounting bracket LH from the transaxle assembly.
12156
79.REMOVE OIL PAN INSULATOR
Remove the 2 bolts and oil pan insulator.
33118D
80.REMOVE STIFFENER PLATE RH
Remove the 4 bolts and stiffener plate RH.
33119C
81.REMOVE STIFFENER PLATE LH
Remove the 4 bolts and stiffener plate LH.
82.FIX ENGINE ASSEMBLY
Using wooden blocks or plate lift attachments, set the engine on a flat surface.
Place wooden blocks or plate lift attachments so that the engine is level.
Never install attachments to the oil pan of the engine assembly or transaxle as doing so may deform the oil pan.
Perform this step while supporting the engine assembly using a sling device and chain block.
30300
83.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
30500
84.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)
31210
85.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31250
86.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
13450
87.REMOVE FLYWHEEL WITH DAMPER ASSEMBLY (for Manual Transaxle)
Using SST, hold the crankshaft pulley.
Using a T55 "TORX" socket wrench, remove the 8 bolts and flywheel with damper assembly.
32101
88.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)
Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly, and front drive plate spacer.
89.INSTALL ENGINE TO ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Install the engine to an engine stand, and remove the sling device and chain block from the engine.
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.
12371A
90.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the 2 bolts, 2 nuts and rear engine mounting insulator.
12372A
91.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
| *A | for Manual Transaxle |
| *B | for Automatic Transaxle |
Remove the 4 bolts and engine mounting insulator LH from the body.
12305
92.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 3 bolts and engine mounting insulator sub-assembly RH from the body.