As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.
for Manual Transaxle:
When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.
Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, camshaft housing sub-assembly, camshaft timing gear assembly, camshaft timing exhaust gear assembly, piston sub-assembly or piston ring.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Temporarily install the engine mounting insulator LH with the 4 bolts.
Tighten the 4 bolts in the sequence shown in the illustration.
Install the wire harness clamp bracket with the bolt.
12305
2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.
Tighten the 3 bolts in the sequence shown in the illustration.
Install the radiator reservoir bracket with the bolt.
12371A
3.INSTALL REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
| *A | for Manual Transaxle |
| *B | for CVT |
Temporarily install the rear engine mounting insulator with the 2 bolts and 2 nuts.
Tighten the 2 bolts and 2 nuts in the sequence shown in the illustration.
43457
4.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.
5.INSTALL ENGINE HANGER
6.REMOVE ENGINE FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach a sling device and hang the engine with a chain block.
Lift the engine and remove it from the engine stand.
7.FIX ENGINE ASSEMBLY
82121
8.INSTALL ENGINE WIRE
Install the engine wire to the engine.
13405
9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
31400
10.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)
31407B
11.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)
12.INSPECT CLUTCH PIPE LINE (for Manual Transaxle)
31407B
13.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)
14.INSTALL CLUTCH TUBE (for Manual Transaxle)
31250
15.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)
31210
16.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31210
17.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)
32101
18.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
30300
19.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
30400
20.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)
36100
21.INSTALL TRANSFER ASSEMBLY
11363A
22.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
23.INSTALL STARTER ASSEMBLY
45319A
24.INSTALL STEERING GEAR HEAT INSULATOR (for RHD)
25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Temporarily install the front engine mounting insulator with the through bolt and nut.
| *1 | Alignment Mark |
| *2 | Protrusion |
Temporarily install the front suspension crossmember with the through bolt.
When installing the suspension crossmember, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.
Place the engine on an engine lifter.
Place the engine on wooden blocks or equivalent so that the engine is level.
Operate the engine lifter and install the engine to the vehicle.
Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine is clear of all wiring and hoses.
While raising the engine into the vehicle, do not allow it to contact the vehicle.
Temporarily install the front suspension crossmember sub-assembly with 2 bolts.
Temporarily install the front suspension member rear brace RH and LH with the 6 bolts.
Install the engine mounting insulator LH with the through bolt and nut.
While holding the bolt in place, tighten the nut.
Install the engine mounting insulator sub-assembly RH with the bolt and 2 nuts.
Tighten the 2 front suspension crossmember bolts.
Tighten the 6 front suspension member rear brace bolts.
Remove the 2 bolts and No. 1 and No. 2 engine hangers.
Install the air fuel ratio sensor bracket with the bolt. Then connect the air fuel ratio sensor connector.
Attach the fuel tube clamp.
Install the front crossmember sub-assembly with the 6 bolts.
Tighten the rear engine mounting insulator bolt.
Check that the protrusion of the engine mounting bracket is aligned with the alignment mark of the engine mounting insulator.
Tighten the front engine mounting insulator bolt and nut.
While holding the bolt in place, tighten the nut.
51218A
26.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH
Install the front suspension member reinforcement LH with the 4 bolts.
51217A
27.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
Install the front suspension member reinforcement RH with the 4 bolts.
32101A
28.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)
37100
29.TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
37100
30.TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
89465
31.CONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
17410
32.INSTALL FRONT EXHAUST PIPE ASSEMBLY
43420G
33.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
43420
34.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
35.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
48069
36.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
37.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
45047
38.CONNECT TIE ROD END SUB-ASSEMBLY LH
45046
39.CONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48810
40.CONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
41.CONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
42.CONNECT FRONT SPEED SENSOR LH
43.CONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
43502H
44.INSTALL FRONT AXLE SHAFT NUT LH
43501H
45.INSTALL FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
45025D
46.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
47.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
48.INSTALL COLUMN HOLE COVER SILENCER SHEET
31418
49.CONNECT CLUTCH HOSE (for Manual Transaxle)
Connect the clutch hose and install the clip to the clutch hose.
Install the clip as far as it will go.
Using a 10 mm union nut wrench, connect the clutch hose to the accumulator to flexible hose tube while holding the clutch hose.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Do not kink or damage the clutch hose.
Do not allow any foreign matter such as dirt or dust to enter the clutch hose from the clip or bracket.
This torque value is effective when the union nut wrench is parallel to the torque wrench.
33820B
50.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)
Connect the clamp of the transmission control cable assembly with the bolt.
Connect the transmission control cable assembly to the transmission control cable support.
Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.
Connect the transmission control cable assembly to the control shaft lever with the nut.
33820B
51.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Connect the control cable to the control cable bracket, and install 2 new clips.
Connect the control cable to the transaxle, and install the 2 washers and 2 clips.
52.CONNECT WIRE HARNESS AND HOSE
Connect the heater water outlet hose and heater water inlet hose to the heater core and slide the 2 clamps to secure the hoses.
Connect the connector tube hose to the air tube and slide the clamp to secure the hose.
for Manual Transaxle:
Attach the clamp and connect the engine wire to the manual transaxle with the bolt.
for CVT:
Attach the clamp and connect the engine wire to the CVT with the bolt.
Connect the starter wire to terminal B with the nut.
Attach the wire harness clamp and connect the terminal cap.
Connect the wire harness and attach the 2 wire harness claws.
Connect the 2 engine room junction block connectors and install the nut.
Install the bolt and attach the 2 wire harness clamps.
23901
53.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION
16571C
54.CONNECT NO. 1 RADIATOR HOSE
for CVT:
Connect the breather plug hose to the clamp.
Connect the No. 1 radiator hose to the cylinder head sub-assembly, and slide the hose clamp to secure the hose.
89661
55.INSTALL ECM
74414B
56.INSTALL BATTERY BRACKET REINFORCEMENT
74411B
57.INSTALL FRONT BATTERY BRACKET
16057
58.INSTALL RADIATOR HOSE SUB-ASSEMBLY
74431
59.INSTALL BATTERY TRAY
28800
60.INSTALL BATTERY
74404A
61.INSTALL BATTERY CLAMP SUB-ASSEMBLY
62.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17705
63.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
88310
64.CONNECT COMPRESSOR ASSEMBLY WITH PULLEY
Using an E8 "TORX" socket wrench, connect the compressor with pulley assembly with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
Tighten the bolts and the nuts in the order shown in the illustration.
Connect the connector and attach the wire harness clamp.
16572D
65.CONNECT NO. 2 RADIATOR HOSE
27020
66.INSTALL GENERATOR ASSEMBLY
16361A
67.INSTALL V-RIBBED BELT
16361A
68.ADJUST V-RIBBED BELT
16470
69.INSTALL RADIATOR RESERVOIR ASSEMBLY
Install the radiator reservoir assembly with the 2 bolts.
Connect the No. 1 and No. 2 water by-pass hoses to the radiator reservoir assembly, and slide the 2 hose clamps to secure the No. 1 and No. 2 water by-pass hose.
70.CONNECT CABLE TO POSITIVE BATTERY TERMINAL
71.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
72.ADD TRANSFER OIL
73.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
74.ADD ENGINE OIL
75.ADD ENGINE COOLANT
76.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
77.INSPECT SHIFT LEVER POSITION (for CVT)
78.INSPECT FOR FUEL LEAK
79.INSPECT FOR COOLANT LEAK
80.INSPECT FOR OIL LEAK
81.INSPECT FOR EXHAUST GAS LEAK
82.INSPECT IGNITION TIMING
83.INSPECT ENGINE IDLE SPEED
84.INSPECT CO/HC
85.ADJUST FRONT WHEEL ALIGNMENT
86.INSTALL NO. 2 ENGINE UNDER COVER
Install the No. 2 engine under cover with the bolt and clip.
50819
87.INSTALL FRONT FLOOR COVER
51443
88.INSTALL REAR ENGINE UNDER COVER RH
Install the rear engine under cover RH with the 3 clips.
51444
89.INSTALL REAR ENGINE UNDER COVER LH
Install the rear engine under cover LH with the 2 clips.
51441
90.INSTALL NO. 1 ENGINE UNDER COVER
11212
91.INSTALL NO. 2 CYLINDER HEAD COVER
92.RESET MEMORY (for CVT)