Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P1092  Maximum Positive Deviation of Rail Pressure Exceeded Concerning Set Flow of Fuel  P1094  Rail Pressure below Threshold during Start  P1097  Minimum Rail Pressure Exceeded  P1099  Maximum Positive Deviation of Rail Pressure Exceeded Concerning Set Value PCV  


DESCRIPTION

For information on the fuel system, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0087 Fuel Rail / System Pressure - Too Low One of following conditions is met (1 trip detection logic):
·

When rail pressure control is performed according to the fuel quantity control valve, the positive control deviation is the standard value or higher for 0.9 seconds.

·

When rail pressure control is performed according to the fuel quantity control valve, the minimum rail pressure is the standard value (approximately 12000 kPa to 14000 kPa) or less for 0.3 seconds.

·

When rail pressure control is performed according to the pressure discharge valve assembly, the positive control deviation is the standard value or higher for 0.8 seconds.

·

When rail pressure control is performed according to the pressure discharge valve assembly, the minimum rail pressure is the standard value (approximately 12000 kPa) or less for 0.3 seconds.


HINT:

The detection standard value is calculated according to the engine speed and vehicle speed.


·

Fuel quantity control valve (fuel supply pump assembly)

·

Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

·

Fuel filter element clogged

·

Fuel leak

·

Injector assembly

·

Lack of fuel

·

Fuel line (air bleeding)

·

Pressure discharge valve assembly

·

Fuel pressure sensor

·

ECM


Comes on DTC stored
P1092 Maximum Positive Deviation of Rail Pressure Exceeded Concerning Set Flow of Fuel When positive control deviation is more than 20000 kPa and volumetric flow via fuel quantity control valve reaches or exceeds the threshold for 0.9 seconds.
(3 trip detection logic)
·

Fuel quantity control valve (fuel supply pump assembly)

·

Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

·

Fuel filter element clogged

·

Fuel leak

·

Injector assembly

·

Lack of fuel

·

Fuel line (air bleeding)

·

Pressure discharge valve assembly

·

Fuel pressure sensor

·

ECM


Does not come on DTC stored
P1094 Rail Pressure below Threshold during Start When the common rail internal pressure is 18000 kPa or lower regardless of whether the engine speed is 160 rpm or higher after the engine is started, a counter is increased every 10 msec. If the counter exceeds a predetermined value for 0.6 seconds.
(3 trip detection logic)
·

Fuel quantity control valve (fuel supply pump assembly)

·

Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

·

Fuel filter element clogged

·

Fuel leak

·

Injector assembly

·

Lack of fuel

·

Fuel line (air bleeding)

·

Pressure discharge valve assembly

·

Fuel pressure sensor

·

ECM


Does not come on DTC stored
P1097 Minimum Rail Pressure Exceeded Common rail internal pressure is less than 12000 to 14000 kPa (varies with engine speed) for 0.3 seconds.
(3 trip detection logic)
·

Fuel leakage (high pressure area)

·

Fuel injector (Injector jammed open)

·

Fuel quantity control valve (fuel supply pump assembly)

·

Injector assembly

·

Pressure discharge valve assembly

·

Fuel pump (Low pressure side)

·

Fuel filter element clogged


Comes on DTC stored
P1099 Maximum Positive Deviation of Rail Pressure Exceeded Concerning Set Value PCV When rail pressure control is performed according to the pressure discharge valve assembly, the positive control deviation is 15000 kPa or higher for 0.75 seconds.
(3 trip detection logic)
·

Fuel pump (Low pressure side)

·

Fuel filter element clogged

·

Fuel pressure sensor

·

Leakage (high pressure area)

·

Injector assembly

·

Fuel quantity control valve (fuel supply pump assembly)

·

Pressure discharge valve assembly

·

Common rail system


Does not come on DTC stored

Related Data List
DTC No. Data List
P0087
P1092
P1094
P1097
P1099
·

Target Common Rail Pressure

·

Common Rail Pressure

·

Quantity Regulation Valve - Current Value from Common Rail

·

Quantity Regulation Valve - Output Duty Cycle

·

Rail Pressure Control Valve - Current Value from Rail Pressure Valve Control

·

Dutycycle Output of Rail Pressure Control Valve



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM and/or injector assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the pressure discharge valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0087, P1092, P1094, P1097 and/or P1099 A
DTC P0087, P1092, P1094, P1097 and/or P1099 and other DTCs B


HINT:

If any DTCs other than P0087, P1092, P1094, P1097 and/or P1099 are output, troubleshoot those DTCs first.




A

2.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

2.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result:
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B




A

3.ADD FUEL

B

6.CLEAR DTC
3.ADD FUEL
Result:
Proceed to
NEXT



NEXT

4.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
4.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
a.

Check the fuel pump operation and for fuel leaks.

HINT:

If the fuel pump operation cannot be performed, inspect the fuel pump control circuit.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P1092, P1094, P1097 AND/OR P1099)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P1092, P1094, P1097 AND/OR P1099)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0087, P1092, P1094, P1097 and/or P1099 B




A

DTC CAUSED BY RUNNING OUT OF FUEL

B

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

Result:
Proceed to
NEXT



NEXT

7.CHECK ENGINE STARTING CONDITION
7.CHECK ENGINE STARTING CONDITION
a.

Check the engine starting condition.

OK:

The engine can be started within 4 seconds.


NOTICE:

Just after starting the engine, visually check for fuel leaks from the fuel supply pump assembly, the injector assemblies, the common rail assembly, and the fuel pipes in high-pressure areas.



Result:
Proceed to
OK
NG



OK

10.CHECK PRESSURE DISCHARGE VALVE ASSEMBLY

NG

8.CHECK FUEL PRESSURE (LOW PRESSURE)
8.CHECK FUEL PRESSURE (LOW PRESSURE)

Result:
Proceed to
OK
NG



OK

10.CHECK PRESSURE DISCHARGE VALVE ASSEMBLY

NG

9.CHECK AND REPLACE FUEL INLET PIPE
9.CHECK AND REPLACE FUEL INLET PIPE
a.

Check the following items (fuel line from fuel tank to supply pump), and repair or replace the malfunctioning part if necessary.

i.

Check for fuel filter clogging.


ii.

Check for fuel freezing in the fuel line when the cold condition.


iii.

Check for clogging or leaks in the fuel pipe and hose between the fuel tank and fuel supply pump assembly.



Result:
Proceed to
NEXT



NEXT

10.CHECK PRESSURE DISCHARGE VALVE ASSEMBLY
10.CHECK PRESSURE DISCHARGE VALVE ASSEMBLY
a.

Inspect the pressure discharge valve assembly.


b.

Perform Active Test.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.


iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Pressure Control Valve / Data List / Dutycycle Output of Rail Pressure Control Valve.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Pressure Control Valve
Data List Display
Dutycycle Output of Rail Pressure Control Valve
50004 371 5 132
OK:

The value of "Dutycycle Output of Rail Pressure Control Valve" changes according to the amount "Actuator Test of Pressure Control Valve" is operated.




Result:
Proceed to
OK
NG



OK

11.CHECK FUEL SUPPLY PUMP ASSEMBLY

NG

17.REPLACE PRESSURE DISCHARGE VALVE ASSEMBLY
11.CHECK FUEL SUPPLY PUMP ASSEMBLY
a.

Remove the fuel quantity control valve and visually check that there are no foreign objects such as scraps in the fuel supply pump assembly.

OK:

No foreign objects present.


HINT:

If foreign objects are present, replace all parts of the high pressure fuel system (fuel supply pump assembly, common rail assembly and fuel hose), and then check that there are no foreign objects such as scraps in the low pressure fuel system (inner part of the fuel tank, low pressure fuel pump and fuel hose).



b.

Check the Data List.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.


iii.

Start the engine.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 371 50,51

v.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Common Rail Pressure is within 10000 kPa of Target Common Rail Pressure when the engine is idling and running at 3000 rpm without load.




Result:
Proceed to
OK
NG



OK

12.PERFORM ACTIVE TEST USING GTS (FUEL BALANCING COMPENSATION (FBC))

NG

16.REPLACE FUEL SUPPLY PUMP ASSEMBLY
12.PERFORM ACTIVE TEST USING GTS (FUEL BALANCING COMPENSATION (FBC))
HINT:

If the Active Test cannot be performed due the engine failing to start, replace the injector assembly and proceed to procedure 13, "CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0088, P1092 or P1094)".


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Fuel Balancing Compensation (FBC) / Data List / Cylinder 1 Quantity Compensation to Cylinder 4 Quantity Compensation.

Powertrain > Engine and ECT > Active Test
Active Test Display
Fuel Balancing Compensation (FBC)
Data List Display
Cylinder 1 Quantity Compensation
Cylinder 2 Quantity Compensation
Cylinder 3 Quantity Compensation
Cylinder 4 Quantity Compensation
50004 371 16 110,111,112,113

e.

Read the value.

Standard value:

-5.0 to 4.0 mg/stk



Result:
Proceed to
OK
NG



OK

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0088, P1092 OR P1094)

NG

15.REPLACE INJECTOR ASSEMBLY
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0088, P1092 OR P1094)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0087, P0088, P1092 or P1094 B




A

END

B

14.REPLACE FUEL PRESSURE SENSOR
14.REPLACE FUEL PRESSURE SENSOR
a.

Replace the fuel pressure sensor.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly of malfunctioning cylinder.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>REMOVAL


b.

Register the injector assembly compensation code.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL SUPPLY PUMP>REMOVAL


b.

Perform the supply pump learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.REPLACE PRESSURE DISCHARGE VALVE ASSEMBLY
a.

Replace the pressure discharge valve assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE DISCHARGE VALVE>REMOVAL


b.

Perform the fuel PCV compensation value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END