Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P011C  Charge Air Cooler Temperature / Intake Air Temperature Correlation Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P011C Charge Air Cooler Temperature / Intake Air Temperature Correlation Bank 1 After 1 or more hours elapse with the ignition switch off, the difference between the air temperature and changed air temperature is equal to or higher than the threshold.
(3 trip detection logic)
·

Intake air temperature sensor

·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

Open or short in Intake air temperature sensor (built into mass air flow meter sub-assembly) circuit

·

ECM


Does not come on DTC stored

HINT:

The threshold used for DTC detection is calculated based on the engine stop time.


Related Data List
DTC No. Data List
P011C
·

Intake Air

·

Intake air temp (Turbo)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the mass air flow meter sub-assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P011C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P011C A
DTC P011C and other DTCs B


HINT:

If any DTCs other than P011C are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))

B

2.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))
a.

Stop the engine when the coolant temperature is more than 78°C (173°F).


b.

Leave the vehicle.

HINT:

To meet the DTC detection conditions, the engine coolant temperature must drop to below 32°C (89°F).



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine when the engine coolant temperature is less than 32°C (89°F).


f.

Idle the engine for 1 minute or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
50003 371 4,54

h.

Read the value of Intake Air on the GTS.

Standard:

Difference between the intake air temperature (Intake Air) and actual outside air temperature is within 10°C (18°F) or less.


HINT:

Temperature readings on the vehicle outside temperature gauge (if equipped) are not suitable for comparing to the intake air temperature reading. The outside temperature gauge has a significant delay built in to prevent swings in the temperature display. Use an accurate thermometer to determine the outside air temperature.



i.

Read the value of Intake Air Temp (Turbo) on the GTS.

Standard:

Difference between the intake air temperature (Intake Air Temp (Turbo)) and actual outside air temperature is within 10°C (18°F) or less.


HINT:

Temperature readings on the vehicle outside temperature gauge (if equipped) are not suitable for comparing to the intake air temperature reading. The outside temperature gauge has a significant delay built in to prevent swings in the temperature display. Use an accurate thermometer to determine the outside air temperature.


Result:
Result Proceed to
OK A
NG (Intake Air value deviated) B
NG (Intake Air Temp (Turbo) value deviated) C




A

8.REPLACE ECM

B

3.INSPECT INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER SUB-ASSEMBLY)

C

6.INSPECT INTAKE AIR TEMPERATURE SENSOR
3.INSPECT INTAKE AIR TEMPERATURE SENSOR (BUILT INTO MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Inspect the intake air temperature sensor (built into mass air flow meter sub-assembly).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

5.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B113-3 (THA) - B112-114 (THA) Always Below 1 Ω
B113-2 (E2G) - B112-129 (EVG) Always Below 1 Ω
B113-3 (THA) or B112-114 (THA) - Body ground Always 10 kΩ or higher
B113-2 (E2G) or B112-129 (EVG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Perform the air flow meter learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.INSPECT INTAKE AIR TEMPERATURE SENSOR
a.

Inspect the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)

NG

10.REPLACE INTAKE AIR TEMPERATURE SENSOR
7.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B115-1 (THA) - B112-79 (THIA) Always Below 1 Ω
B115-2 (E2) - B112-89 (ETHI) Always Below 1 Ω
B115-1 (THA) or B112-79 (THIA) - Body ground Always 10 kΩ or higher
B115-2 (E2) or B112-89 (ETHI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END