1.REMOVE FRONT WHEEL
51441
2.REMOVE NO. 1 ENGINE UNDER COVER
for 2WW: (Click hereEngine / Hybrid System>2WW COOLING>RADIATOR>REMOVAL)
for 2AR-FE: (Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FE: (Click hereEngine / Hybrid System>3ZR-FE COOLING>COOLANT>REPLACEMENT)
51444C
3.REMOVE REAR ENGINE UNDER COVER LH
for 2WW: (Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 2AR-FE: (Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FE: (Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
51443
4.REMOVE REAR ENGINE UNDER COVER RH
for 2WW: (Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>DRIVE BELT>REMOVAL)
for 2AR-FE: (Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FE: (Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
5.DRAIN AUTOMATIC TRANSAXLE FLUID
6.DRAIN MANUAL TRANSAXLE OIL
for EA64: (Click hereDrivetrain>EA64 MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT)
for EB61: (Click hereDrivetrain>EB61 MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT)
for EB63: (Click hereDrivetrain>EB63 MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT)
7.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
for K111: (Click hereDrivetrain>K111 MULTIDRIVE / CVT>FRONT DIFFERENTIAL OIL SEAL>REPLACEMENT)
for K114: (Click hereDrivetrain>K114 MULTIDRIVE / CVT>FRONT DIFFERENTIAL OIL SEAL>REPLACEMENT)
43502H
8.REMOVE FRONT AXLE SHAFT NUT LH
43501H
9.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
10.DISCONNECT FRONT SPEED SENSOR LH
11.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
12.REMOVE FRONT STABILIZER LINK ASSEMBLY LH
48820B
13.REMOVE FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
48069
14.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
15.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
16.DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH
Remove the bolt and detach the 2 guides.
| *a | Matchmark |
Put matchmarks on the front drive shaft assembly LH and front axle hub sub-assembly.
Do not use a punch to make the matchmarks.
Using a plastic-faced hammer, disconnect the front drive shaft assembly LH from the steering knuckle with axle hub.
Do not damage the front axle inboard joint boot and front drive shaft dust cover LH.
Do not excessively push out the front drive shaft assembly LH from the front axle hub.
17.DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH
Use the same procedure described for the LH side.
43420
18.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
Using SST, remove the front drive shaft assembly LH.
Do not damage the transaxle oil seal, front axle inboard joint boot and front drive shaft dust cover LH.
Do not drop the front drive shaft assembly LH.
When carrying the front drive shaft assembly LH, hold it horizontally.
Hook the SST claw at the position shown in the illustration to remove the front drive shaft assembly LH.
43410
19.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
w/o Drive Shaft Bearing Case:
Disconnect the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Do not damage the transaxle oil seal, front axle inboard joint boot, front drive shaft dust cover RH and front drive shaft dust cover.
Do not drop the front drive shaft assembly RH.
When carrying the front drive shaft assembly RH, hold it horizontally.
Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.
w/ Drive Shaft Bearing Case:
for 2AR-FE, 3ZR-FE:
Remove the 2 bolts and pull out the front drive shaft assembly RH together with the drive shaft bearing case sub-assembly from the transaxle.
Do not damage the transaxle oil seal, front axle inboard joint boot, front drive shaft dust cover RH and front drive shaft dust cover.
Do not drop the front drive shaft assembly RH.
When carrying the front drive shaft assembly RH, hold it horizontally.
for 2WW:
Using a T50 ''TORX'' socket wrench, remove the 2 bolts and pull out the front drive shaft assembly RH together with the drive shaft bearing case sub-assembly from the transaxle.
Do not damage the transaxle oil seal, front axle inboard joint boot, front drive shaft dust cover RH and front drive shaft dust cover.
Do not drop the front drive shaft assembly RH.
When carrying the front drive shaft assembly RH, hold it horizontally.
43420G
20.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
Using a screwdriver, remove the front drive shaft hole snap ring LH.
Do not damage the spline of the front drive inboard joint assembly LH.