Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD with Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377039 BRAKE BOOSTER(for RHD with Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD with Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Temporarily install the brake booster assembly to the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



b.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Fully tighten the lock nut when adjusting the brake pedal height.



c.

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


d.
C407856C03
1.188,1.938 1.354,1.938 1.354,1.938 1.656,1.479 true 1.969,1.302 2.385,1.833 2.385,1.833 2.552,1.833 true 2.594,1.74 2.802,1.948 0.208,0.208 10 true *a 1,1.844 1.208,2.052 0.208,0.208 10 true *b
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly


Temporarily install each brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




e.
C407861

Install a new brake tube clamp to the vehicle body with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


f.

Engage the clamp and install a new brake tube clamp to the vehicle body.


g.
C407860C02
0.354,0.219 0.667,0.375 0.313,0.156 10 false *a 1.74,0.24 2.052,0.396 0.313,0.156 10 false *b
*a except Manual Transaxle
*b for Manual Transaxle


Connect the brake lines.

i.

for Manual Transaxle:

Engage the 4 clamps to install a new brake tube clamp to the brake lines.


ii.

except Manual Transaxle:

Engage the 3 clamps to install a new brake tube clamp to the brake lines.



h.
C407859C02
0.354,0.219 0.667,0.375 0.313,0.156 10 false *a 1.74,0.24 2.052,0.396 0.313,0.156 10 false *b
*a except Manual Transaxle
*b for Manual Transaxle


Install the brake tube clamp.

i.

for Manual Transaxle:

Engage the 6 clamps to install a new brake tube clamp to the brake lines.


ii.

except Manual Transaxle:

Engage the 5 clamps to install a new brake tube clamp to the brake lines.



i.
C407858

Engage the 5 clamps to install a new brake tube clamp to the brake lines.


j.
C409051C01
2.719,2.708 2.823,3.031 2.823,3.031 2.906,3.031 false 1.781,2.99 2.094,3.146 0.313,0.156 10 false *a 2.958,2.969 3.271,3.125 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




k.

w/ Stop and Start System:

i.

Connect the connector to the vacuum sensor assembly.



l.

Connect the connector to the vacuum warning switch assembly.


Hide 88707 3.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.
C407855

Engage the 2 clamps to connect the suction pipe sub-assembly to the vehicle body.


Hide 47313 4.CONNECT FRONT NO. 3 BRAKE TUBE

a.
C407880

Engage the clamp and install a new brake tube clamp.


b.
C407877

Engage the clamp to connect the front No. 3 brake tube to the brake tube clamp.


c.
C409053C01
2.719,2.698 2.802,3.094 2.802,3.094 2.885,3.094 false 1.781,3 2.094,3.156 0.313,0.156 10 false *a 2.938,3.01 3.25,3.167 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Temporarily install front No. 3 brake tube to the front flexible hose.


d.

Using a union nut wrench, tighten the front No. 3 brake tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 88710E 5.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/o Sub-cool Accelerator)

Hide 88707 6.CONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

Hide 88710G 7.CONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

Hide 44763A 8.CONNECT NO. 1 HOSE TO HOSE TUBE

a.
C407857

Connect the No. 1 hose to hose tube to the vehicle body with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 44772 9.INSTALL CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C409050C01
1.542,1.365 1.958,1.781 1.958,1.781 2.125,1.781 true 2.208,1.698 2.375,1.865 0.167,0.167 10 true *a
*a Paint Mark


Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the check valve to connector tube hose, face the paint mark up.

·

Make sure that the tabs of the clip are facing upward.




Hide 11.CONNECT WIRE HARNESS

a.
C406469

Engage the 2 clamps to Connect the wire harness to the brake pedal support assembly.


b.

Connect the connector.


Hide 84340 13.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 87211A 14.INSTALL NO. 2 AIR DUCT

Hide 73900 15.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 47201 16.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 17.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 18.ADD ENGINE COOLANT