Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for A25A-FKS)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374934 AIR CONDITIONING UNIT(for A25A-FKS) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for A25A-FKS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 5.CONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Attach the clamp.

E408066C01
6,0.385 6.24,0.604 0.24,0.219 12 true *A
*A w/ ECU - -



ii.

Connect the connector.



b.

for RHD:

i.

Attach the clamp.

E408068


ii.

Connect the connector.



Hide 88650N 6.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 7.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Hide 55307C 10.TEMPORARILY INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 55306A 11.TEMPORARILY INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 12.TIGHTEN INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Hide 14.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

Hide 89261A 15.INSTALL ENGINE STOP AND START ECU (for RHD with Stop and Start System)

Hide 82877 16.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 8598A 17.INSTALL DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 18.CONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Connect the lever connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

E408016C01
1,1.5 1.188,1.698 0.188,0.198 10 true *a 3.427,1.719 3.615,1.917 0.188,0.198 10 true *a 3.615,2.708 3.802,2.906 0.188,0.198 10 true *a 3.052,4.281 3.24,4.479 0.188,0.198 10 true *a 4.271,3.354 4.458,3.552 0.188,0.198 10 true *a 3.802,2.167 3.99,2.365 0.188,0.198 10 true *b 4.271,4.333 4.458,4.531 0.188,0.198 10 true *a 4.063,4.031 4.281,4.229 0.219,0.198 12 true *A 4.333,4.938 4.521,5.135 0.188,0.198 10 true *a 0.552,2.604 0.771,2.802 0.219,0.198 12 true *C 2.844,4.031 3.063,4.229 0.219,0.198 12 true *B
*A for Type A *B for Type B
*C for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



ii.

Attach the clamp.


iii.

Connect the connector.


iv.

Attach the guide.


v.

Connect the ground wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vi.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vii.

Attach the clamp.

E408015C01
2.156,3.469 2.49,3.469 true 2.302,3.625 2.635,3.625 true 2.375,4.948 2.552,5.135 0.177,0.188 10 true *a 2.365,1.646 2.542,1.833 0.177,0.188 10 true *a 1.969,3.375 2.146,3.563 0.177,0.188 10 true *a 3,2.531 3.177,2.719 0.177,0.188 10 true *a 3.458,2.75 3.635,2.938 0.177,0.188 10 true *a 4.698,1.073 4.875,1.26 0.177,0.188 10 true *a 2.115,4.854 2.292,5.042 0.177,0.188 10 true *b 2.135,3.531 2.313,3.719 0.177,0.188 10 true *b 5.167,4.333 5.344,4.521 0.177,0.188 10 true *b
*a Clamp *b Guide



viii.

Attach the guide.


ix.

Connect the 3 ground wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


x.
E408014C01
1.531,1.281 1.698,1.469 0.167,0.188 10 true *a 2.177,1.063 2.344,1.25 0.167,0.188 10 true *b
*a Clamp
*b Guide


Connect the 2 connectors.


xi.

Attach the guide and clamp.



b.

for RHD:

i.

Connect the lever connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

E408018C01
5.021,4.51 5.25,4.708 0.229,0.198 12 true *A 4.146,5.365 4.323,5.542 0.177,0.177 10 true *a 4.26,4.719 4.438,4.896 0.177,0.177 10 true *a 4.313,3.833 4.49,4.01 0.177,0.177 10 true *a 4.906,3.292 5.083,3.469 0.177,0.177 10 true *a 5.219,2.198 5.396,2.375 0.177,0.177 10 true *a 2.875,1.542 3.052,1.719 0.177,0.177 10 true *a 1.25,0.479 1.427,0.656 0.177,0.177 10 true *a 0.813,0.698 0.99,0.875 0.177,0.177 10 true *a 2.781,3.99 2.958,4.167 0.177,0.177 10 true *a 1,5.156 1.177,5.333 0.177,0.177 10 true *a 4.729,2.75 4.906,2.927 0.177,0.177 10 true *b 3.979,1.521 4.156,1.698 0.177,0.177 10 true *b
*A for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



ii.

Attach the clamp.


iii.

Connect the connector.


iv.

Attach the guide.


v.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vi.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vii.

Attach the clamp.

E408017C01
4.656,2.115 4.99,2.115 true 1.344,2.521 1.521,2.708 0.177,0.188 10 true *a 4.792,1.646 4.969,1.833 0.177,0.188 10 true *a 5.094,0.594 5.271,0.781 0.177,0.188 10 true *a 4.99,2.031 5.167,2.219 0.177,0.188 10 true *a 3.281,2.875 3.458,3.063 0.177,0.188 10 true *a 6.271,4.594 6.448,4.781 0.177,0.188 10 true *a 2.979,2.573 3.156,2.76 0.177,0.188 10 true *b 5.188,2.677 5.365,2.865 0.177,0.188 10 true *b
*a Clamp *b Guide



viii.

Attach the guide.


ix.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



Hide 82877 19.INSTALL ECU INTEGRATION BOX RH (for RHD)

Hide 20.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

Hide 55308B 21.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 55085 22.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 87212 26.INSTALL REAR NO. 1 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 3 air duct.


Hide 87212F 27.INSTALL REAR NO. 2 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 4 air duct.


Hide 58510C 29.INSTALL FRONT FLOOR FRONT CARPET ASSEMBLY

Hide 58569D 30.INSTALL FRONT FLOOR CAUTION PLATE COVER

Hide 78010F 31.INSTALL ACCELERATOR PEDAL ASSEMBLY

Hide 62414A 33.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Install the lower center pillar garnish LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


b.

Return the front door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


c.

Return the rear door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


Hide 73220 34.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 67918E 35.INSTALL REAR DOOR SCUFF PLATE LH

Hide 62413A 36.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described as for the lower center pillar garnish LH.


Hide 73210 37.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described as for the front seat outer belt assembly LH.


Hide 67917C 38.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described as for the rear door scuff plate LH.


Hide 73233 39.INSTALL OUTER LAP BELT ANCHOR COVER

Hide 40.INSTALL NAVIGATION ECU WITH BRACKET (w/ Navigation System)

Hide 41.INSTALL TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)

Hide 42.INSTALL NAVIGATION ECU WITH BRACKET (w/ Dummy Case)

HINT:

Use the same procedure described as for the navigation ECU with bracket or telephone transceiver assembly with bracket.


Hide 45250 43.INSTALL STEERING COLUMN ASSEMBLY

Hide 44.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 45.INSTALL FRONT SEAT ASSEMBLY LH

Hide 46.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 87245 47.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose.

·

Make sure the inlet heater water hose is securely inserted to the stopper. However, If the end of the inlet heater water hose is cut diagonally, it is acceptable for the entire circumference of the tip to not contact the stopper.

·

Connect the inlet heater water hose so that its marking faces the top of the vehicle.



E408019C01
4.76,2.604 5.094,2.604 true 4.115,3.115 4.448,3.115 true 5.583,3.354 5.583,3.521 5.583,3.521 5.917,3.521 true 1.26,2.052 1.375,2.219 0.115,0.167 10 true A 4.438,0.406 4.844,0.719 0.406,0.313 10 false *a 5.479,1.542 5.885,1.854 0.406,0.313 10 false *c 4.604,2.521 5.01,2.833 0.406,0.313 10 false *1 3.958,3.031 4.365,3.344 0.406,0.313 10 false *2 5.375,2.177 5.781,2.49 0.406,0.313 10 false *d 5.938,3.427 6.344,3.74 0.406,0.313 10 false *b
*1 Hose Clip *2 Inlet Heater Water Hose
*a View A *b Stopper
*c Hose Clip Installation Angle (270°) *d Hose Clip Installation Range (2 to 7 mm (0.0787 to 0.276 in.))



b.

Make sure to install the hose clip within the range shown in the illustration.


Hide 87246 48.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose.

·

Make sure the outlet heater water hose is securely inserted to the stopper. However, If the end of the outlet heater water hose is cut diagonally, it is acceptable for the entire circumference of the tip to not contact the stopper.

·

Connect the outlet heater water hose so that its marking faces the top of the vehicle.



E408020C01
4.75,2.604 5.083,2.604 true 4.094,3.115 4.427,3.115 true 5.594,3.365 5.594,3.531 5.594,3.531 5.927,3.531 true 1.073,1.823 1.188,1.99 0.115,0.167 10 true A 4.49,0.313 5.052,0.604 0.563,0.292 10 false *a 5.615,0.646 6.177,0.938 0.563,0.292 10 false *c 5.375,2.156 5.938,2.448 0.563,0.292 10 false *d 4.583,2.521 5.146,2.813 0.563,0.292 10 false *1 3.927,3.031 4.49,3.323 0.563,0.292 10 false *2 5.938,3.438 6.5,3.729 0.563,0.292 10 false *b
*1 Hose Clip *2 Outlet Heater Water Hose
*a View A *b Stopper
*c Hose Clip Installation Angle (270°) *d Hose Clip Installation Range (2 to 7 mm (0.0787 to 0.276 in.))



b.

Make sure to install the hose clip within the range shown in the illustration.

NOTICE:

Make sure that the hose clamps do not contact each other.



Hide 88710E 49.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/o Sub-cool Accelerator)

a.

Remove the vinyl tape wrapped around the connection of the air conditioning tube and accessory assembly and the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free from foreign matter.



d.

Connect the air conditioning tube and accessory assembly.

NOTICE:
·

Do not apply excessive force to the air conditioning tube and accessory assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




Hide 88707 50.CONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

a.

Remove the vinyl tape wrapped around the connection of the suction pipe sub-assembly and suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.

NOTICE:
·

Do not apply excessive force to the suction pipe sub-assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




e.
E408021C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the 1-point tightening plate as shown in the illustration.


f.
E408005

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88710G 51.CONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

a.

Remove the vinyl tape wrapped around the connection of the No. 2 air conditioning tube and accessory assembly and the No. 2 air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the No. 2 air conditioning tube and accessory assembly.

NOTICE:
·

Do not apply excessive force to the No. 2 air conditioning tube and accessory assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




e.
E408022C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the 1-point tightening plate as shown in the illustration.


f.
E408009

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55704B 53.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 55752 54.INSTALL COWL VENTILATOR SPLASH SHIELD

HINT:

Install using the same procedure that is performed when replacement of the cowl ventilator splash shield is necessary.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 55.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 56.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 57.ADD ENGINE COOLANT