Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for M20A-FKS)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374931 AIR CONDITIONING UNIT(for M20A-FKS) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for M20A-FKS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 88650N 6.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 45250 7.TEMPORARILY INSTALL STEERING COLUMN ASSEMBLY (for Manual Transaxle RHD)

a.

Temporarily install the steering column assembly with the bolt and 2 nuts.

NOTICE:
·

Do not release the lever before installing the part to the vehicle.

·

At this time, make sure that nothing other than the fastening surface of the steering column assembly contacts the instrument panel reinforcement assembly.



E408776C01
0.583,1.885 0.917,1.885 true 4.188,1.865 4.521,1.865 true 0.417,1.792 0.594,1.979 0.177,0.188 10 true *a 4.01,1.771 4.188,1.958 0.177,0.188 10 true *a 0.146,0.115 0.542,0.469 0.396,0.354 12 false *A 3.76,0.115 4.156,0.469 0.396,0.354 12 false *B
*A for Type A *B for Type B
*a Lever - -
V100135

Bolt
V100136

Nut



Hide 8.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

·

Be careful not to damage the internal components of the instrument panel reinforcement assembly with air conditioning unit assembly on the glass etc. Only perform installation after first taking the appropriate actions.



a.

Install the instrument panel reinforcement assembly with air conditioning unit assembly to the guide as shown in the illustration.

NOTICE:
·

Do not allow the heater radiator unit sub-assembly heater pipe or cooler expansion valve to strike the body.

·

Make sure that both parts are securely installed to the guide.



E408777C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Temporarily install the 4 bolts (C).

E408773C01
0,0 0,0 false
V100135

Bolt (B)
V100136

Bolt (C)
V100137

Nut - -



c.

for Manual Transaxle LHD:

i.
E408774C01
0,0 0,0 false
V100135

Bolt (D)


Temporarily install the bolt (D).



d.

Temporarily install the bolt (B).


e.
E405772C01
0,0 0,0 false
V100135

Bolt (A)


Temporarily install the 3 bolts (A).


f.

Temporarily install the nut.


g.

Tighten the 4 bolts (C).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


h.

Tighten the 3 bolts (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


i.

for Manual Transaxle LHD:

i.

Tighten the bolt (D).

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



j.

Tighten the bolt (B).

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 55307C 11.TEMPORARILY INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 55306A 12.TEMPORARILY INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 13.TIGHTEN INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Hide 14.CONNECT INSTRUMENT PANEL WIRE

a.

for CVT LHD:

i.

Attach the clamp.

E408768C01
3.208,5.375 3.375,5.563 0.167,0.188 10 true *a 4,3.802 4.167,3.99 0.167,0.188 10 true *a 1.625,3.865 1.792,4.052 0.167,0.188 10 true *a 1.479,4.917 1.646,5.104 0.167,0.188 10 true *a 3.771,1.208 3.938,1.396 0.167,0.188 10 true *a 2.344,0.729 2.51,0.917 0.167,0.188 10 true *a 2.646,0.802 2.813,0.99 0.167,0.188 10 true *a 5.344,1.417 5.51,1.604 0.167,0.188 10 true *a 4.063,2.604 4.229,2.792 0.167,0.188 10 true *a 4.917,2.833 5.083,3.021 0.167,0.188 10 true *a 5.073,4.354 5.24,4.542 0.167,0.188 10 true *a 1.969,0.427 2.135,0.615 0.167,0.188 10 true *a 1.542,0.323 1.719,0.479 0.177,0.156 10 true *b 5.104,5 5.271,5.188 0.167,0.188 10 true *b
*a Clamp *b Guide
V100135

Bolt
V100136

Connector



ii.

Connect the connector.


iii.

Attach the guide.


iv.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



b.

for Manual Transaxle LHD:

i.

Attach the clamp.

E408769C01
1.135,0.417 1.469,0.417 true 1.458,0.094 1.792,0.094 1.792,0.094 1.792,0.26 true 2.302,0.375 2.49,0.552 0.188,0.177 10 true *a 2.573,0.417 2.76,0.594 0.188,0.177 10 true *a 3.531,0.75 3.719,0.927 0.188,0.177 10 true *a 1.521,3.958 1.708,4.135 0.188,0.177 10 true *a 1.313,5.115 1.5,5.292 0.188,0.177 10 true *a 3.427,5.458 3.615,5.635 0.188,0.177 10 true *a 5.26,4.531 5.448,4.708 0.188,0.177 10 true *a 4.604,2.865 4.792,3.042 0.188,0.177 10 true *a 4.156,2.563 4.344,2.74 0.188,0.177 10 true *a 5.563,1.281 5.75,1.458 0.188,0.177 10 true *a 5.167,5.031 5.354,5.208 0.188,0.177 10 true *b 1.302,0 1.625,0.281 0.323,0.281 10 false *a 0.979,0.333 1.302,0.615 0.323,0.281 10 false *b
*a Clamp *b Guide
V100135

Bolt
V100136

Connector



ii.

Connect the connector.


iii.

Attach the guide.


iv.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



c.

for RHD:

i.

Attach the clamp.

E408771C01
2.469,5 2.656,5.188 0.188,0.188 10 true *a 1.771,1.073 1.958,1.26 0.188,0.188 10 true *a 4.948,1.021 5.135,1.208 0.188,0.188 10 true *a 3.156,2.188 3.344,2.375 0.188,0.188 10 true *a 1.875,2.427 2.063,2.615 0.188,0.188 10 true *a 1.906,2.969 2.094,3.156 0.188,0.188 10 true *a 1.865,3.177 2.052,3.365 0.188,0.188 10 true *b 1.646,4.438 1.833,4.625 0.188,0.188 10 true *b
*a Clamp *b Guide
V100135

Bolt
V100136

Connector



ii.

Connect the connector.


iii.

Attach the guide.


iv.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


v.
E408770C01
1.333,1.427 1.521,1.615 0.188,0.188 10 true *a 1.667,0.906 1.854,1.094 0.188,0.188 10 true *b
*a Clamp
*b Guide


Connect the 2 connectors.


vi.

Attach the guide and clamp.



Hide 15.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

Hide 89261A 16.INSTALL ENGINE STOP AND START ECU (for RHD with Stop and Start System)

Hide 82877 17.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 18.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle LHD)

Hide 8598A 19.INSTALL DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 20.CONNECT INSTRUMENT PANEL WIRE

a.

for CVT LHD:

i.

Connect the lever connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

E408763C01
3.302,1.688 3.49,1.885 0.188,0.198 10 true *a 3.417,2.76 3.604,2.958 0.188,0.198 10 true *a 4.208,4.927 4.396,5.125 0.188,0.198 10 true *a 4.083,3.292 4.271,3.49 0.188,0.198 10 true *a 4.167,4.219 4.354,4.417 0.188,0.198 10 true *a 3.635,2.125 3.823,2.323 0.188,0.198 10 true *b 1.594,2.333 1.781,2.531 0.188,0.198 10 true *a 2.135,4.073 2.365,4.271 0.229,0.198 12 true *A
*A for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



ii.

Attach the clamp.


iii.

Connect the connector.


iv.

Attach the guide.


v.

Connect the ground wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vi.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vii.

Attach the clamp.

E408762C01
2.229,3.552 2.563,3.552 true 2.26,4.823 2.438,5.01 0.177,0.188 10 true *a 2.302,1.615 2.479,1.802 0.177,0.188 10 true *a 2.365,3.115 2.542,3.302 0.177,0.188 10 true *a 3.344,2.667 3.521,2.854 0.177,0.188 10 true *a 4.688,1.219 4.865,1.406 0.177,0.188 10 true *a 1.813,4.552 1.99,4.74 0.177,0.188 10 true *b 2.063,3.448 2.24,3.635 0.177,0.188 10 true *b 4.885,4.385 5.063,4.573 0.177,0.188 10 true *b 2.896,2.438 3.073,2.625 0.177,0.188 10 true *a
*a Clamp *b Guide



viii.

Attach the guide.


ix.

Connect the 3 ground wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



b.

for Manual Transaxle LHD:

i.

Connect the lever connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

E408765C01
1.51,2.406 1.698,2.604 0.188,0.198 10 true *a 2.719,1.698 2.906,1.896 0.188,0.198 10 true *a 3.073,2.938 3.26,3.135 0.188,0.198 10 true *a 3.771,4.458 3.958,4.656 0.188,0.198 10 true *a 3.833,5.146 4.021,5.344 0.188,0.198 10 true *a 3.708,3.5 3.896,3.698 0.188,0.198 10 true *a 3.219,2.313 3.406,2.51 0.188,0.198 10 true *b 1.906,4.021 2.135,4.229 0.229,0.208 12 true *A
*A for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



ii.

Attach the clamp.


iii.

Connect the connector.


iv.

Attach the guide.


v.

Connect the ground wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vi.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vii.

Attach the clamp.

E408764C01
2.01,3.594 2.344,3.594 true 2.031,4.865 2.208,5.052 0.177,0.188 10 true *a 2.094,1.646 2.271,1.833 0.177,0.188 10 true *a 3.094,2.76 3.271,2.948 0.177,0.188 10 true *a 2.146,3.156 2.323,3.344 0.177,0.188 10 true *a 4.438,1.083 4.615,1.271 0.177,0.188 10 true *a 1.594,4.583 1.771,4.771 0.177,0.188 10 true *b 5.906,3.01 6.083,3.198 0.177,0.188 10 true *b 1.844,3.5 2.021,3.688 0.177,0.188 10 true *b 2.698,2.094 2.875,2.281 0.177,0.188 10 true *a
*a Clamp *b Guide
V100135

Bolt
V100136

Nut



viii.

Attach the guide.


ix.

Connect the 3 ground wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


x.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.

for LHD:

i.
E408761C01
1.302,1.344 1.5,1.542 0.198,0.198 10 true *a 1.646,0.813 1.844,1.01 0.198,0.198 10 true *b
*a Clamp
*b Guide


Connect the 2 connectors.


ii.

Attach the guide and clamp.



d.

for RHD:

i.

Connect the lever connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

E408767C01
0.729,0.573 0.906,0.76 0.177,0.188 10 true *a 1.146,0.385 1.323,0.573 0.177,0.188 10 true *a 2.604,1.51 2.781,1.698 0.177,0.188 10 true *a 5.104,2.167 5.281,2.354 0.177,0.188 10 true *a 4.76,3.292 4.938,3.479 0.177,0.188 10 true *a 4.521,2.781 4.698,2.969 0.177,0.188 10 true *b 4.073,4.813 4.25,5 0.177,0.188 10 true *a 3.906,5.563 4.083,5.75 0.177,0.188 10 true *a 4.104,3.865 4.281,4.052 0.177,0.188 10 true *a 2.563,4.042 2.74,4.229 0.177,0.188 10 true *a 1.198,6 1.375,6.188 0.177,0.188 10 true *a 4.021,1.292 4.198,1.479 0.177,0.188 10 true *b 5.333,4.302 5.542,4.49 0.208,0.188 12 true *A
*A for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



ii.

Attach the clamp.


iii.

Connect the connector.


iv.

Attach the guide.


v.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vi.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vii.

Attach the clamp.

E408766C01
1.427,2.188 1.604,2.385 0.177,0.198 10 true *a 4.583,1.521 4.76,1.719 0.177,0.198 10 true *a 5.323,0.49 5.5,0.688 0.177,0.198 10 true *a 4.604,1.854 4.781,2.052 0.177,0.198 10 true *a 3.135,2.656 3.313,2.854 0.177,0.198 10 true *a 5.99,4.302 6.167,4.5 0.177,0.198 10 true *a 4.969,2.427 5.146,2.625 0.177,0.198 10 true *b 2.854,2.417 3.031,2.615 0.177,0.198 10 true *b
*a Clamp *b Guide



viii.

Attach the guide.


ix.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



Hide 82877 21.INSTALL ECU INTEGRATION BOX RH (for RHD)

Hide 22.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for CVT LHD)

Hide 55308B 23.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY


b.

for Manual Transaxle LHD:

i.
E408760C01
1.406,1.323 1.583,1.51 0.177,0.188 10 true *a 2.229,0.594 2.406,0.781 0.177,0.188 10 true *a 1.208,0.698 1.385,0.885 0.177,0.188 10 true *b
*a Clamp
*b Guide
V100135

Bolt
V100136

Nut


Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Attach the clamp and guide.




Hide 55085 24.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 58861B 25.INSTALL NO. 1 CONSOLE BOX DUCT

a.
E408759C01
0.135,0.115 0.365,0.302 0.229,0.188 12 true *A 0.135,2.448 0.365,2.635 0.229,0.188 12 true *B
*A for CVT
*B for Manual Transaxle


Attach the clamp.


b.

Install the No. 1 console box duct with the clip.


Hide 87212 28.INSTALL REAR NO. 1 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 3 air duct.


Hide 87212F 29.INSTALL REAR NO. 2 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 4 air duct.


Hide 58510C 31.INSTALL FRONT FLOOR FRONT CARPET ASSEMBLY

Hide 58569D 32.INSTALL FRONT FLOOR CAUTION PLATE COVER

Hide 78010F 33.INSTALL ACCELERATOR PEDAL ASSEMBLY

Hide 62414A 35.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Install the lower center pillar garnish LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


b.

Return the front door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


c.

Return the rear door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


Hide 73220 36.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 67918E 37.INSTALL REAR DOOR SCUFF PLATE LH

Hide 62413A 38.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described as for the lower center pillar garnish LH.


Hide 73210 39.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described as for the front seat outer belt assembly LH.


Hide 67917C 40.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described as for the rear door scuff plate LH.


Hide 73233 41.INSTALL OUTER LAP BELT ANCHOR COVER

Hide 42.INSTALL NAVIGATION ECU WITH BRACKET (w/ Navigation System)

Hide 43.INSTALL TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)

Hide 44.INSTALL NAVIGATION ECU WITH BRACKET (w/ Dummy Case)

HINT:

Use the same procedure described as for the navigation ECU with bracket or telephone transceiver assembly with bracket.


Hide 45250 45.INSTALL STEERING COLUMN ASSEMBLY (except Manual Transaxle RHD)

Hide 45250 46.TIGHTEN STEERING COLUMN ASSEMBLY (for Manual Transaxle RHD)

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Tighten the steering column assembly with the bolt and 2 nuts in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

After the column is installed, check the tilt operation.

·

If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.

Tighten the nuts and check the tilt operation again.



E408758C01
0.115,0.104 0.49,0.344 0.375,0.24 12 false *A 3.708,0.104 4.083,0.344 0.375,0.24 12 false *B 0.854,0.25 0.958,0.427 0.104,0.177 10 true 1 2.323,0.25 2.427,0.427 0.104,0.177 10 true 1 4.448,0.25 4.552,0.427 0.104,0.177 10 true 1 5.927,0.25 6.031,0.427 0.104,0.177 10 true 1 1.146,3.24 1.25,3.417 0.104,0.177 10 true 2 4.74,3.24 4.844,3.417 0.104,0.177 10 true 2
*A for Type A *B for Type B
V100135

Bolt
V100136

Nut



b.
E408778C01
0.135,0.115 0.573,0.448 0.438,0.333 12 false *A 0.135,2.333 0.573,2.667 0.438,0.333 12 false *B
*A for Type A
*B for Type B


Attach the clamp.


c.

Connect each connector.


Hide 45220 47.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (for Manual Transaxle RHD)

a.
C406892C01
1.615,0.573 1.052,0.469 1.052,0.469 1.625,0.5 true 0.844,0.365 1.01,0.552 0.167,0.188 10 true *a
*a Matchmark
V113147

Connect in this Direction


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


b.

Connect the steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 87211 48.INSTALL NO. 1 AIR DUCT (for Manual Transaxle RHD)

Hide 49.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 50.INSTALL FRONT SEAT ASSEMBLY LH

Hide 51.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 87245 52.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose.

·

Make sure the inlet heater water hose is securely inserted to the stopper. However, If the end of the inlet heater water hose is cut diagonally, it is acceptable for the entire circumference of the tip to not contact the stopper.

·

Connect the inlet heater water hose so that its marking faces the top of the vehicle.



E408779C01
4.76,2.604 5.094,2.604 true 4.115,3.115 4.448,3.115 true 5.583,3.354 5.583,3.521 5.583,3.521 5.917,3.521 true 1.677,1.771 1.792,1.938 0.115,0.167 10 true A 4.583,0.417 4.99,0.729 0.406,0.313 10 false *a 5.625,1.573 6.031,1.885 0.406,0.313 10 false *c 4.604,2.521 5.01,2.833 0.406,0.313 10 false *1 3.958,3.031 4.365,3.344 0.406,0.313 10 false *2 5.375,2.177 5.781,2.49 0.406,0.313 10 false *d 5.938,3.427 6.344,3.74 0.406,0.313 10 false *b
*1 Hose Clip *2 Inlet Heater Water Hose
*a View A *b Stopper
*c Hose Clip Installation Angle (270°) *d Hose Clip Installation Range (2 to 7 mm (0.0787 to 0.276 in.))



b.

Make sure to install the hose clip within the range shown in the illustration.


Hide 87246 53.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose.

·

Make sure the outlet heater water hose is securely inserted to the stopper. However, If the end of the outlet heater water hose is cut diagonally, it is acceptable for the entire circumference of the tip to not contact the stopper.

·

Connect the outlet heater water hose so that its marking faces the top of the vehicle.



E408780C01
4.75,2.604 5.083,2.604 true 4.094,3.115 4.427,3.115 true 5.594,3.365 5.594,3.531 5.594,3.531 5.927,3.531 true 1.667,1.417 1.781,1.583 0.115,0.167 10 true A 4.552,0.344 5.115,0.635 0.563,0.292 10 false *a 5.802,0.635 6.365,0.927 0.563,0.292 10 false *c 5.375,2.156 5.938,2.448 0.563,0.292 10 false *d 4.583,2.521 5.146,2.813 0.563,0.292 10 false *1 3.927,3.031 4.49,3.323 0.563,0.292 10 false *2 5.938,3.438 6.5,3.729 0.563,0.292 10 false *b
*1 Hose Clip *2 Outlet Heater Water Hose
*a View A *b Stopper
*c Hose Clip Installation Angle (270°) *d Hose Clip Installation Range (2 to 7 mm (0.0787 to 0.276 in.))



b.

Make sure to install the hose clip within the range shown in the illustration.

NOTICE:

Make sure that the hose clamps do not contact each other.



Hide 88710E 54.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/o Sub-cool Accelerator)

a.

Remove the vinyl tape wrapped around the connection of the air conditioning tube and accessory assembly and the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:
Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent



c.

Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free from foreign matter.



d.

Connect the air conditioning tube and accessory assembly.

NOTICE:
·

Do not apply excessive force to the air conditioning tube and accessory assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




Hide 88707 55.CONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

a.

Remove the vinyl tape wrapped around the connection of the suction pipe sub-assembly and suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:
Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.

NOTICE:
·

Do not apply excessive force to the suction pipe sub-assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




e.
E408781C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the 1-point tightening plate as shown in the illustration.


f.
E405743

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88710G 56.CONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

a.

Remove the vinyl tape wrapped around the connection of the No. 2 air conditioning tube and accessory assembly and the No. 2 air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the No. 2 air conditioning tube and accessory assembly.

NOTICE:
·

Do not apply excessive force to the No. 2 air conditioning tube and accessory assembly.

·

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)




e.
E408782C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the 1-point tightening plate as shown in the illustration.


f.
E405743

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55704B 58.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 55752 59.INSTALL COWL VENTILATOR SPLASH SHIELD

HINT:

Install using the same procedure that is performed when replacement of the cowl ventilator splash shield is necessary.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 60.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 61.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 62.ADD ENGINE COOLANT