Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2019.02
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0377461 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.



PROCEDURE

Hide 75922M 1.INSTALL NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)

Hide 75986G 2.INSTALL FRONT DOOR OUTSIDE STRIPE LH (w/ Black Out Tape)

Hide 75966B 3.INSTALL FRONT DOOR NO. 4 STRIPE LH (w/ Black Out Tape)

Hide 67001A 4.INSTALL FRONT DOOR PANEL CUSHION

a.
B522056

Attach the claw and install the front door panel cushion.

HINT:

Use the same procedure described for the other side.



Hide 5.INSTALL HOLE PLUG

a.
B522057

Install the hole plug.

HINT:

Use the same procedure described for the other side.



Hide 6.INSTALL SCREW GROMMET

a.
B522055

Attach the claw and install the screw grommet.

HINT:

Use the same procedure described for the other side.



Hide 75074 7.INSTALL FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 67864B 8.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP LH

a.
B522054

Attach the clip and install the front door No. 2 weatherstrip LH.


Hide 75754A 9.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING LH

Hide 75792 10.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B524160

Attach the claw to install a new door window frame moulding clip.


Hide 67856B 11.INSTALL FRONT DOOR PANEL PROTECTOR LH

Hide 75756D 12.INSTALL DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

Hide 67862 13.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B522062

Attach the clip and install the front door weatherstrip LH.


b.
B536491C01
1.01,0.906 1.323,1.063 0.313,0.156 10 false *a 1.01,1.969 1.323,2.125 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Check that the front door weatherstrip LH is securely installed to the rail of the front door outside moulding sub-assembly LH as shown in the illustration.

NOTICE:

If the front door weatherstrip LH is not securely installed, water may leak into the vehicle.



Hide 68620 14.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

When reusing a bolt (B):

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




b.
B522051C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the front door check assembly LH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69760B 15.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

Hide 69720D 16.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

Hide 69036A 17.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

Hide 69318C 18.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)

a.

When reusing front door lock with motor assembly LH:

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSTALLATION


Hide 69040A 19.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

Hide 69760B 20.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

Hide 69720D 21.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

Hide 69318C 22.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)

Hide 69040A 23.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

Hide 69202A 24.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly LH.


b.
B522044

w/ Entry and Start System:

i.

Attach the wire harness clamp.



c.
B522068C01
0.167,0.083 0.438,0.333 0.271,0.25 10 true *a 0.146,2.417 0.417,2.667 0.271,0.25 10 true *b
*a Inside
*b Outside


Attach the guide as shown in the illustration.


d.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly LH with the "TORX" screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69312 25.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B522069C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door lock open rod LH on the front door lock with motor assembly LH as shown in the illustration.

HINT:

Check that the front door lock open rod LH is securely attached to the front door lock with motor assembly LH.



b.
B522070C01
1.219,0.531 1.927,0.344 true 1.979,0.229 2.219,0.417 0.24,0.188 10 false *1
*1 Snap
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the front door lock open rod LH to the front door outside handle frame sub-assembly LH and attach the snap of the front door outside handle as shown in the illustration.


Hide 69242F 26.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B522041

Attach the guide and install the front door rear outside handle pad.


Hide 69241H 27.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B522040

Attach the claw and guide to install the front door front outside handle pad.


Hide 28.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)

a.

Apply MP grease to the sliding parts of the front door lock cylinder assembly LH.


b.
B522035

Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly LH with the "TORX" screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B522034

Install the hole plug.


Hide 69217E 29.INSTALL FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B522071C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw of the front door outside handle cover RH in the direction indicated by the arrow.


b.
B522038

Using a T30 "TORX" socket wrench, install the front door outside handle cover RH with the "TORX" screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B522037

Install the hole plug.


Hide 69220 30.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B522072C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door outside handle assembly LH in the direction of the arrow shown in the illustration.


b.
B522073C01
1.521,0.75 1.104,0.563 true 0.865,0.417 1.083,0.635 0.219,0.219 10 true *1
*1 Holder
V113147

Install in this Direction


Attach the holder as shown in the illustration.


c.
B522074

w/ Entry and Start System:

i.

Attach the claw to connect the connector and connector cover.


ii.
B522075C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and close the connector cover as shown in the illustration.



Hide 68126 31.INSTALL FRONT DOOR FIX WINDOW GLASS LH

a.
B522076C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door fix window glass LH as shown in the illustration.


Hide 67402F 32.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

a.
B522077C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Temporarily install the front door front lower frame sub-assembly LH in the direction indicated by the arrows, in the order shown in the illustration.


b.

Install the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.
B522027C01
0,0 0,0 false
V113147

Lift up in this Direction


Lift up the front door weatherstrip LH and install the screw as shown in the illustration.


d.

Install the screw.


Hide 67404F 33.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B522026

Attach the guide.


b.

Install the front door rear lower frame sub-assembly LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 85720C 34.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69802 35.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door window regulator sub-assembly LH.


b.
B522079C01
0,0 0,0 false
V113147

Install in this Direction


Insert the front door window regulator sub-assembly LH to the service hole as shown in the illustration.


c.
B522024C01
1.354,1.854 1.49,2.031 0.135,0.177 10 true 1 0.969,0.042 1.104,0.219 0.135,0.177 10 true 1 1.042,0.719 1.177,0.896 0.135,0.177 10 true 2 1.833,0.146 1.969,0.323 0.135,0.177 10 true 2 2.49,0.344 2.625,0.521 0.135,0.177 10 true 3 1.781,0.969 1.917,1.146 0.135,0.177 10 true 4 2.396,1.24 2.531,1.417 0.135,0.177 10 true 3
V100135

Nut
V100136

Connector


Install the front door window regulator sub-assembly LH with the 7 nuts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not damage the front door panel with the front door window regulator sub-assembly LH.



d.

Connect the connector.


Hide 68151D 36.INSTALL FRONT DOOR GLASS RUN LH

a.
B522080N01
0.417,1.427 0.583,1.604 0.167,0.177 10 true A 0.865,1.333 1.031,1.51 0.167,0.177 10 false A 1.76,0.667 1.969,0.875 0.208,0.208 10 false B 1.823,0.208 2.031,0.396 0.208,0.188 10 false B 2.51,1.635 2.667,1.823 0.156,0.188 10 true C 2.969,1.604 3.125,1.792 0.156,0.188 10 true C 0.542,2.292 0.906,2.49 0.365,0.198 10 false A-A 1.594,1.156 2.125,1.396 0.531,0.24 10 false B-B 2.552,2.292 3.125,2.583 0.573,0.292 10 false C-C

Install the front door glass run LH to the groove in front door front lower frame sub-assembly LH and front door rear lower frame sub-assembly LH.


Hide 67664C 37.INSTALL DOOR FRAME GARNISH LH

a.
B522081C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and install the door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.


Hide 68102 38.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

for Driver Side:

i.

Connect the multiplex network master switch assembly connector.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly connector.



c.

Connect the cable to the negative (-) auxiliary battery terminal.






d.

Turn the ignition switch to ON.


e.

Move the front door window regulator sub-assembly LH until the installation bolts can be seen.


f.
B522082C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Temporarily install the front door glass sub-assembly LH to the front door window regulator assembly LH in the order shown in the illustration.

NOTICE:

Be careful not to damage the front door glass sub-assembly LH.



g.
B522020

Install the front door glass sub-assembly LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Move the front door glass sub-assembly LH until the open position.


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

iii.

iv.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

After disconnecting the cable from the negative (-) auxiliary battery terminal, wait for at least 90 seconds to start the operation.

·

If the airbag deploys for any reason, it may cause a serious accident.





k.

for Driver Side:

i.

Disconnect the multiplex network master switch assembly connector.



l.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly connector.



m.

Remove the protective tape.


n.
B522018

Install the hole plug.


Hide 75712B 39.INSTALL FRONT DOOR BELT MOULDING LH

Hide 67832 41.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.
B522083C01
0,0 0,0 false
V113147

Install in this Direction


Pass the front door lock remote control cable assembly and front door inside locking cable assembly through the front door service hole cover LH.


b.
B522084C01
1.177,0.177 1.448,0.156 true 0.979,0.073 1.156,0.24 0.177,0.167 10 true *a 2.438,1.938 2.563,2.115 0.125,0.177 10 true 1 1.333,0.271 1.458,0.448 0.125,0.177 10 true 2 1.76,1.833 1.885,2.01 0.125,0.177 10 true 3 2.854,1.219 2.979,1.396 0.125,0.177 10 true 3
*a Clip A


Align with the position of clip A as shown in the illustration.


c.

Attach the clip and install the front door service hole cover LH in the order shown in the illustration.


d.
B526925C01
1.302,2.375 1.542,2.375 false 1.573,2.281 1.885,2.479 0.313,0.198 10 false *a
*a Bead Mark
V113147

Turn in this Direction
V100135

Service Hole Cover Clip


Install the service hole cover clip knob at an angle of 45°.


e.

Turn the service hole cover clip 45° clockwise and align the positions of the bead mark and knob.

HINT:

Use the same procedure for the other service hole cover clips.



f.
B522014

Attach the clamp.


g.

Connect the connector.


Hide 86160 42.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 87940 43.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 87964 44.INSTALL OUTER MIRROR INSTALL HOLE COVER LH

Hide 68193C 45.INSTALL FRONT DOOR FRONT BELT SEAL LH

a.
B522086C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door front belt seal LH as shown in the illustration.


b.
B522087C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and partially install the front door weatherstrip LH with the clip.


Hide 68195B 46.INSTALL FRONT DOOR REAR BELT SEAL LH

a.
B522088C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door rear belt seal LH to the front door inner glass weatherstrip LH as shown in the illustration.


Hide 68172A 47.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B522139C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door inner glass weatherstrip LH with front door rear belt seal LH as shown in the illustration.


b.
B522140C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and partially install the front door weatherstrip LH with the clip.


Hide 69206B 48.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B522141C01
0,0 0,0 false
V113147

Install in this Direction


Temporarily install the front door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.


b.
B522007

Attach the claw and clamp to install the front door inside handle sub-assembly LH.


Hide 84927 49.INSTALL SEAT MEMORY SWITCH (w/ Seat Memory Switch)

Hide 67602 50.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B522006

w/ Seat Memory Switch:

i.

Connect the connector.



b.
B522142C01
2.281,0.854 2.698,0.792 true 2.24,1.354 2.521,1.74 true 2.76,0.656 2.958,0.833 0.198,0.177 10 true *1 2.5,1.833 2.688,2 0.188,0.167 10 true *2
*1 Front Door Inside Looking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Attach the clamp and connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle sub-assembly as shown in the illustration.


c.
B522143C01
2.896,1.333 3.021,1.531 0.125,0.198 10 true 1 0.354,1.688 0.479,1.885 0.125,0.198 10 true 2 2.583,1.771 2.708,1.969 0.125,0.198 10 true 3 2.583,1.313 2.708,1.51 0.125,0.198 10 true 4 2.26,1.344 2.385,1.542 0.125,0.198 10 true 5 1.948,1.365 2.073,1.563 0.125,0.198 10 true 6 1.604,1.375 1.729,1.573 0.125,0.198 10 true 7 1.24,1.375 1.365,1.573 0.125,0.198 10 true 8 0.792,1.396 0.917,1.594 0.125,0.198 10 true 9
V113147

Install in this Direction


Attach the claw and clip to install the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.

HINT:

Attach the claws and clips as shown in the illustration.



d.
B522144C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and install the 3 screws as shown in the illustration.


e.

Remove the protective tape.


Hide 84930 51.INSTALL DOOR CONTROL SWITCH ASSEMBLY (w/ Door Control Switch)

Hide 84810 52.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84870A 53.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)

Hide 84040 54.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 55.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect the 2 connectors.


b.
B522147C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide in the direction indicated by the arrow shown in the illustration.


c.
B522148C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the multiplex network master switch assembly with front door armrest base panel.


d.

Remove the protective tape.


Hide 56.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

w/ Door Control Switch:

i.

Connect the 2 connectors.



b.

w/o Door Control Switch:

i.

Connect the connector.



c.
B522145C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide in the direction indicated by the arrow shown in the illustration.


d.
B522146C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the power window regulator switch assembly with front door armrest base panel.


e.

Remove the protective tape.


Hide 74642A 57.INSTALL FRONT DOOR ASSIST GRIP COVER LH

a.
B522149C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide in the direction indicated by the arrow shown in the illustration.


b.
B522150C01
0.667,1.208 0.802,1.396 0.135,0.188 10 true 1 1.021,1.146 1.156,1.333 0.135,0.188 10 true 2 1.344,1.094 1.479,1.281 0.135,0.188 10 true 3 1.677,1.01 1.813,1.198 0.135,0.188 10 true 4 1.927,0.948 2.063,1.135 0.135,0.188 10 true 5 2.125,0.781 2.26,0.969 0.135,0.188 10 true 4 2.219,0.5 2.354,0.688 0.135,0.188 10 true 3 2.427,0.24 2.563,0.427 0.135,0.188 10 true 2 2.854,0.615 2.99,0.802 0.135,0.188 10 true 3 2.771,0.927 2.906,1.115 0.135,0.188 10 true 4 1.813,1.708 1.948,1.896 0.135,0.188 10 true 4 1.458,1.781 1.594,1.969 0.135,0.188 10 true 3 1.094,1.885 1.229,2.073 0.135,0.188 10 true 2 0.75,1.969 0.885,2.156 0.135,0.188 10 true 1
V113147

Install in this Direction


Attach the claw in the order shown in the illustration.


c.

Attach the clip and install the front door assist grip cover LH.


d.

Remove the protective tape.


Hide 69278B 58.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

a.
B521991

Attach the claw and install the door inside handle bezel LH.


Hide 59.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 65351A 60.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 61.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 62.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 65. INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 66. CHECK POWER WINDOW CONTROL SYSTEM

Hide 67. CHECK POWER DOOR LOCK CONTROL SYSTEM