Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076406 SEAT BELT _0377521 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64910N 2.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD

Hide 58417H 5.REMOVE REAR NO. 3 FLOOR BOARD

Hide 64993 6.REMOVE REAR DECK FLOOR BOX (w/o Spare Tire)

Hide 58386 7.REMOVE REAR FLOOR FINISH PLATE

Hide 65351A 8.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 9.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 11.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 12.REMOVE REAR SEATBACK ASSEMBLY LH

Hide 73350C 13.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)

Hide 14.REMOVE REAR SEATBACK ASSEMBLY RH

Hide 71304C 15.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH

Hide 71303C 16.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73706 17.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH

Hide 73705 18.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67918E 19.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67917C 20.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 58467H 21.REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)

Hide 58466J 22.REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)

Hide 58464D 23.REMOVE BATTERY SERVICE COVER BOARD (for HV Model)

Hide 58577E 24.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE

Hide 62332C 25.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Pull back the rear door opening trim weatherstrip LH so that the deck trim side panel assembly LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


Hide 62331C 26.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
·

Use the same procedure described for the LH side.

·

Pull back the rear door opening trim weatherstrip RH so that the deck trim side panel assembly RH can be removed.



Hide 62552F 27.REMOVE REAR SEAT SIDE GARNISH LH

Hide 62551F 28.REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 73708A 29.REMOVE TETHER ANCHOR BRACKET SET

Hide 58460D 30.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 64740E 31.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 64730J 32.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 62480A 33.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Hide 62470A 34.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73370E 35.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

a.
B521438

Remove the bolt and the floor anchor of the rear seat outer belt assembly LH.


b.

w/ Pretensioner and Force Limiter:

i.
B521439C01
1.063,0.99 0.75,0.688 true 0.594,0.5 0.906,0.656 0.313,0.156 10 false *a
*a Locking Button
V113147

Remove in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.




c.
B521441C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut.


d.

Detach the guide to remove the rear seat outer belt assembly LH.


e.
B521442

Remove the bolt.


f.

Detach the guide to remove the rear seat outer belt anchor bracket sub-assembly LH.


Hide 73360D 36.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

a.
B529792

Remove the bolt and floor anchor of the rear seat outer belt assembly RH.


b.

w/ Pretensioner and Force Limiter:

i.
B529793C01
1.135,0.708 0.781,0.979 true 1.146,0.563 1.458,0.719 0.313,0.156 10 false *a
*a Locking Button
V113147

Remove in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.




c.
B529794C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut.


d.

Detach the guide to remove the rear seat outer belt assembly RH.


e.
B529795

Remove the bolt.


f.

Detach the guide to remove the rear seat outer belt anchor bracket sub-assembly RH.