Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL PUMP (w/ Canister Pump Module) › from 2020.08
RM3620E _51 Engine / Hybrid System _076684 A25A-FXS FUEL _0375751 FUEL PUMP(w/ Canister Pump Module) A

A25A-FXS FUEL  FUEL PUMP(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of fuel pump Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 5.REMOVE BATTERY HOLE COVER

Hide 6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 7.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 8.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918E 9.REMOVE REAR DOOR SCUFF PLATE LH

Hide 58467H 10.REMOVE NO. 3 BATTERY SERVICE COVER BOARD

Hide 67917C 11.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 58466J 12.REMOVE NO. 2 BATTERY SERVICE COVER BOARD

Hide 58464D 13.REMOVE BATTERY SERVICE COVER BOARD

Hide 58903A 14.REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY

Hide 58325E 15.REMOVE REAR FLOOR SERVICE HOLE COVER

a.

Fold back the floor carpet.


b.
A428818

Remove the 3 bolts and rear floor service hole cover.


c.
A434603

Disconnect the 3 connectors from the fuel suction with pump and gauge tube assembly and fuel gauge wire.


Hide 77404 17.DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
A434606

Disconnect the fuel tank vent hose sub-assembly from the fuel suction with pump and gauge tube assembly.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209C 18.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A434607C01
0.75,3.885 0.917,3.885 0.917,3.885 1.417,3.552 true 1.635,0.354 2.156,0.188 2.156,0.188 2.323,0.188 true 0.552,1.115 0.802,1.115 0.802,1.115 1.479,0.729 true 0.76,2.458 0.927,2.458 0.927,2.458 1.427,2.958 true 2.063,2.99 2.563,2.719 2.563,2.719 2.729,2.719 true 2.042,3.5 2.375,3.5 2.375,3.5 2.375,3.635 true 2.042,3.635 2.792,3.635 false 2.344,0.094 2.594,0.25 0.25,0.156 10 true *1 0.333,1.021 0.552,1.198 0.219,0.177 10 true *2 0.573,2.354 0.885,2.51 0.313,0.156 10 false *a 2.771,2.625 3.083,2.781 0.313,0.156 10 false *b 0.563,3.792 0.875,3.948 0.313,0.156 10 false *c 2.823,3.542 3.135,3.698 0.313,0.156 10 false *d
*1 Tube Joint Clip
*2 Fuel Tank Main Tube Sub-assembly
*a Nylon Tube
*b Fuel Tube Joint
*c Plate Sub-assembly
*d O-ring
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and plate sub-assembly are stuck, push and pull to release them.




Hide 77144 19.REMOVE FUEL PUMP GAUGE RETAINER

a.
A434605

Detach the claw and remove the fuel sender gauge wire from the fuel pump gauge retainer.


b.
A434608

Detach the claw and remove the No. 1 fuel tube clamp from the fuel pump gauge retainer.


c.

Remove the fuel pump gauge retainer.

i.
A428824C01
1.052,3.01 1.385,3.01 true 2.188,0.385 2.49,0.26 2.49,0.26 2.688,0.26 true 1.854,1.281 2.313,1.615 2.313,1.615 2.51,1.615 true 2,0.875 2.667,0.875 true 2.542,1.51 2.75,1.708 0.208,0.198 10 true *c 1.417,2.917 1.625,3.094 0.208,0.177 10 true *d 2.708,0.167 2.938,0.333 0.229,0.167 10 true *a 2.698,0.792 2.948,0.958 0.25,0.167 10 true *b
*a SST (Plate)
*b SST (Bolt)
*c SST (Claw)
*d Insertion Point


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A428825C01
1.802,0.906 2.427,0.635 2.427,0.635 2.635,0.635 true 1.688,1.729 2.615,1.729 true 2.156,4.271 2.156,3.854 true 2.583,1.115 2.417,1.115 2.417,1.115 1.563,1.594 true 2.188,2.188 2.583,2.188 true 2.396,2.813 2.229,2.813 2.229,2.813 1.469,2.729 true 2.667,0.531 2.896,0.698 0.229,0.167 10 true *a 2.604,1.031 2.833,1.208 0.229,0.177 10 true *b 2.646,1.625 2.844,1.802 0.198,0.177 10 true *c 2.615,2.083 2.844,2.26 0.229,0.177 10 true *d 2.094,4.292 2.323,4.469 0.229,0.177 10 true *e 2.417,2.708 2.646,2.885 0.229,0.177 10 true *e
*a SST (Handle)
*b Extension Bar
*c SST (Bolt)
*d SST (Plate)
*e SST (Claw)


Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

CAUTION:

When turning SST (handle), take care not to hit the console box assembly with your hands or SST (handle).


NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction with pump and gauge tube assembly, remove the fuel pump gauge retainer.



Hide 77020A 20.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A428826

Remove the gasket from the fuel tank assembly.