Home › Engine / Hybrid System › A25B-FXS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.08
RM3620E _51 Engine / Hybrid System _080117 A25B-FXS ENGINE MECHANICAL _0390036 CYLINDER HEAD GASKET A

A25B-FXS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment
1.

Clear the zero point calibration data and stored linear solenoid valve calibration data.

2.

Perform initialization and calibration of the linear solenoid valve.

3.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:
·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 88310 3.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16207 4.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 5.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 17167 6.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 9.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 10.REMOVE EGR COOLER ASSEMBLY

Hide 25601 11.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16279 14.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 16278 15.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 17177 17.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 18.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 19.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 20.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 21.REMOVE NO. 7 WATER BY-PASS HOSE

Hide 23807 22.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 23.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 24.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 26.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 28.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 31.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 32.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 33.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 34.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 35.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 36.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 37.DISCONNECT NO. 1 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411195

Slide the clip and disconnect the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264D 38.DISCONNECT NO. 2 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411196

Slide the clip and disconnect the No. 2 water by-pass hose from the No. 1 water by-pass pipe sub-assembly.


Hide 13470 39.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16305E 41.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

Hide 11201 42.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 43.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 44.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 45.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 46.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 47.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 48.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 49.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 51.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 52.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 53.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 54.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 55.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 56.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 57.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 61.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 62.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 64.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 65.REMOVE CYLINDER HEAD GASKET

A403803

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 66.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 67.INSPECT CYLINDER HEAD SUB-ASSEMBLY