15643
1.REMOVE OIL FILTER DRAIN PLUG
15620
2.REMOVE OIL FILTER CAP ASSEMBLY
04152
3.REMOVE OIL FILTER ELEMENT
15781
4.REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)
15671
5.REMOVE OIL FILTER BRACKET
13471
6.REMOVE CRANKSHAFT PULLEY
12108
7.REMOVE OIL FILLER CAP SUB-ASSEMBLY
12185
8.REMOVE OIL FILLER CAP HOUSING
Remove the 2 bolts, filler cap housing and gasket.
19100P
9.REMOVE SPARK PLUG
11102A
10.REMOVE VVT SENSOR (for Bank 1)
Remove the 2 bolts and 2 VVT sensors.
11102A
11.REMOVE VVT SENSOR (for Bank 2)
Remove the 2 bolts and 2 VVT sensors.
11102A
12.REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
19312
13.REMOVE CRANK POSITION SENSOR PROTECTOR
Remove the 2 bolts and sensor protector.
11401G
14.REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and crankshaft position sensor.
15340
15.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH
Remove the 2 bolts and 2 oil control valves.
15330B
16.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH
Remove the 2 bolts and 2 oil control valves.
11202
17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
11201
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
15678E
19.REMOVE OIL CONTROL VALVE FILTER LH
Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.
15678D
20.REMOVE OIL CONTROL VALVE FILTER RH
Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.
11193
21.REMOVE SPARK PLUG TUBE GASKET
Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
Using a screwdriver, pry out the gaskets.
Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.
Tape the screwdriver tip before use.
Be careful not to damage the cylinder head cover.
16100
22.REMOVE ENGINE WATER PUMP ASSEMBLY
11302
23.REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
16322
24.REMOVE INLET WATER PIPE
11301C
25.REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL
Place the timing chain cover on wooden blocks.
Place the oil pump on a wooden block.
Using a screwdriver and wooden block, pry out the oil seal.
Tape the screwdriver tip before use.
Do not damage the surface of the oil seal press fit hole.
26.SET NO. 1 CYLINDER TO TDC / COMPRESSION
13540
27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side)
13559
28.REMOVE CHAIN TENSIONER SLIPPER (for LH Side)
13561
29.REMOVE NO. 1 CHAIN VIBRATION DAMPER (for LH Side)
13506
30.REMOVE CHAIN SUB-ASSEMBLY (for LH Side)
13560A
31.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
13540
32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side)
13559
33.REMOVE CHAIN TENSIONER SLIPPER (for RH Side)
13561
34.REMOVE NO. 1 CHAIN VIBRATION DAMPER (for RH Side)
13506
35.REMOVE CHAIN SUB-ASSEMBLY (for RH Side)
13550
36.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
13521A
37.REMOVE CRANKSHAFT TIMING GEAR KEY
Using a screwdriver, remove the 2 timing gear keys from the crankshaft.
38.REMOVE CAMSHAFT (for Bank 1)
11104A
39.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
40.REMOVE CAMSHAFT (for Bank 2)
11103C
41.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
13801
42.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
13750
43.REMOVE VALVE LASH ADJUSTER ASSEMBLY
13716
44.REMOVE VALVE STEM CAP
11102
45.REMOVE CYLINDER HEAD LH
11116
46.REMOVE NO. 2 CYLINDER HEAD GASKET
11101
47.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11115
48.REMOVE CYLINDER HEAD GASKET
11445
49.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 water jacket spacers from the cylinder head.
Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.
12203A
50.REMOVE VENTILATION PIPE GASKET
Using a screwdriver, pry out the ventilation pipe gasket.
Tape the screwdriver tip before use.
16877
51.REMOVE NO. 1 HEAT EXCHANGER COVER
Remove the 12 bolts and 2 nuts.
Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.
Tape the screwdriver tip before use.
12102A
52.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 14 bolts and 2 nuts.
Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
Be careful not to damage the contact surfaces of the oil pans.
12101
53.REMOVE OIL PAN SUB-ASSEMBLY
Remove the 14 bolts and 2 nuts.
Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
Tape the screwdriver tip before use.
Be careful not to damage the contact surfaces of the cylinder block and oil pan.
12121
54.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 7 bolts and baffle plate.
15104
55.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 bolts, oil strainer and O-ring.
11381
56.REMOVE ENGINE REAR OIL SEAL RETAINER
Remove the 6 bolts and oil seal retainer.
Using a screwdriver, pry out the oil seal retainer.
Tape the screwdriver tip before use.
12109A
57.REMOVE OIL DRAIN PIPE SUB-ASSEMBLY
Remove the bolt and oil drain pipe.
Remove the O-ring.
11381A
58.REMOVE ENGINE REAR OIL SEAL
Place the oil seal retainer on wooden blocks.
Using a screwdriver and hammer, tap out the oil seal.
59.REMOVE RING PIN
It is not necessary to remove the ring pin unless it is being replaced.
60.REMOVE STUD BOLT
If the stud bolt is deformed or its threads are damaged, replace it.