Home › General › MAINTENANCE › CHASSIS › from 2016.10
RM27L0U _V1 General _049292 MAINTENANCE _0235514 CHASSIS N

MAINTENANCE  CHASSIS  GENERAL MAINTENANCE  


PROCEDURE

Hide 1.INSPECT POWER STEERING FLUID (Except North America)

a.

Hide 2.INSPECT STEERING LINKAGE & GEAR HOUSING

a.

Check the steering wheel free play (See page Steering>STEERING COLUMN>STEERING SYSTEM>ON-VEHICLE INSPECTION).


b.

Check the steering linkage for looseness or damage.

i.

Check that the tie rod ends do not have excessive play.


ii.

Check that the dust seals and boots are not damaged.


iii.

Check that the boot clamps are not loose.


iv.

Check that the steering gear housing is not damaged.


v.

Check that the connectors are properly connected to the steering gear housing.



Hide 3.INSPECT STEERING GEAR HOUSING OIL

a.

Check for steering gear housing oil leakage.

If leakage is found, check and repair the cause.


Hide 4.INSPECT BALL JOINT AND DUST COVER

a.

Inspect the ball joints for excessive looseness.

i.

Jack up the front of the vehicle and place wooden blocks with a height of 180 to 200 mm (7.09 to 7.87 in.) under the front tires.


ii.

Lower the vehicle until the front coil spring has about half its ordinary load. Place stands under the vehicle for safety.


iii.

Check that the front wheels are pointing straight ahead. Use wheel chocks on all 4 wheels.


iv.

Using a lever, pry up the end of the lower arm. Check the amount of play.

Maximum ball joint vertical play:

0 mm (0 in.)


If there is any play, replace the ball joint.



b.

Check the dust cover for damage.


Hide 5.INSPECT DRIVE SHAFT BOOTS

a.

Check the drive shaft boots for loose clamps, grease leakage, kinks or damage.


Hide 6.INSPECT AUTOMATIC TRANSMISSION FLUID

Type See procedures
AB60E See page (Click here)
AB60F See page (Click here)

Hide 7.REPLACE AUTOMATIC TRANSMISSION FLUID

Type See procedures
AB60E See page (Click here)
AB60F See page (Click here)

Hide 8.INSPECT AUTOMATIC TRANSMISSION FLUID COOLER HOSE AND CONNECTIONS

a.

Check the automatic transmission fluid cooler hoses (water by-pass hoses) for cracks, leakage, loose connections and deformation.


Hide 9.INSPECT TRANSFER OIL (for 4WD)

Hide 10.REPLACE TRANSFER OIL (for 4WD)

a.

Hide 11.INSPECT FRONT DIFFERENTIAL OIL (for 4WD) AND REAR DIFFERENTIAL OIL

Hide 12.REPLACE FRONT DIFFERENTIAL OIL (for 4WD) AND REAR DIFFERENTIAL OIL

a.

Replace the differential oil (See page Drivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL OIL>REPLACEMENT).


Hide 13.LUBRICATE PROPELLER SHAFT (4WD ONLY) AND TIGHTEN BOLTS

a.

for 4WD:

Lubricate the propeller shaft by referring to the lubrication chart. Before pumping in grease, wipe off any mud and dust on the grease fitting.

i.

for Front propeller shaft

U153600E02
1.542,1.74 1.094,0.958 false 4.719,0.344 5.083,0.906 true 1.583,0.177 2.302,0.354 0.719,0.177 10 false Front Side 6.438,0.844 6.604,1.021 0.167,0.177 10 false A 6.24,1.948 6.75,2.125 0.51,0.177 10 false View A 1.563,1.667 2.031,1.823 0.469,0.156 10 false No. 1 4.333,0.271 4.802,0.427 0.469,0.156 10 false No. 2 4.781,1.635 5.25,1.792 0.469,0.156 10 false No. 2 4.854,2.375 5.323,2.531 0.469,0.156 10 false No. 1


ii.

for Rear propeller shaft

C158514E02
6.497,1.369 6.608,1.524 0.111,0.155 10 A 1.22,2.009 2.130,2.188 0.911,0.179 10 Grease Fitting 4.228,2.03 5.139,2.209 0.910,0.179 10 Grease Fitting 5.745,3.317 6.221,3.461 0.475,0.144 10 View A 4.387,2.86 5.298,3.039 0.910,0.179 10 Grease Fitting 0.71,1.434 1.2,2.084 false 5.651,1.437 5.123,2.103 false



b.

Tighten the bolts of the propeller shaft.

Type See procedures
Front propeller shaft See page (Click here)
Rear propeller shaft (for 2WD) See page (Click here)
Rear propeller shaft (for 4WD) See page (Click here)


Hide 14.INSPECT FRONT AND REAR SUSPENSION (Except North America)

Type See procedures
Front See page (Click here)
Rear See page (Click here)