Home › Drivetrain › 8HP51 (AUTOMATIC TRANSMISSION / TRANSAXLE) › B58 TRANSMISSION WIRE
RM3650E _52 Drivetrain _079902 8HP51 AUTOMATIC TRANSMISSION / TRANSAXLE _0387760 B58 TRANSMISSION WIRE A

8HP51 AUTOMATIC TRANSMISSION / TRANSAXLE  B58 TRANSMISSION WIRE  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Working on 12 V vehicle electrical system.

Risk of short circuits! Risk of fire!

-

Detach battery earth lead from battery.




NOTICE:
·

Damage to battery terminal, the safety battery terminal or the battery state sensor.

Damaged battery terminals can lead to malfunctions or vehicle electrical system faults.

-

Pull off battery terminal from battery pole by carefully moving to and fro. Do not pry off using a tool.




PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 85010 2.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

Hide 55788A 3.REMOVE COWL TOP VENTILATOR LOUVER PROTECTOR

Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 51219 6.REMOVE FRONT SUSPENSION MEMBER LOWER PROTECTOR

Hide 58166A 7.REMOVE FRONT FLOOR COVER LH

Hide 58165C 8.REMOVE FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 58151 10.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

Hide 58151A 12.REMOVE NO. 1 FLOOR HEAT INSULATOR

HINT:

Use the same as for the No. 2 floor heat insulator.


Hide 15.DISCONNECT All CONNECTORS FROM THE ECM AND FROM THE NO. 1 INTEGRATION RELAY

NOTICE:
·

Electrostatic discharge.

Damage to or destruction of electrical components.

-

Only touch the housings of electrical components. Do not touch pins or multi-pin connectors directly.

-

For additional information see:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




HINT:
·

Follow instructions for removing and installing control units.

-

For additional information see:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



·

Disconnecting control units may cause fault code entries and functional limitations. Fault code entries must be read out and deleted if necessary.



a.
A442111

Release snap-lock couplings (1).


b.

Feed the cover (2) out toward the top and remove.


c.
A442112

Unlock and disconnect all plug connections (1).


d.
A442204

Unlock and disconnect all plug connections (1).


Hide 82125 16.REMOVE TRANSMISSION WIRE

a.

Overview of the transmission wire

C411684

NOTICE:
·

Damage to wires when disconnecting connectors and plug connections.

Sheared wires can cause a short circuit.

-

Do not pull on the wires when disconnecting connectors and plug connections.





b.
C413369

Unlock connector (1) and pull off.


c.

Disconnect connector (2) from the integrated supply module.


d.

Disconnect connector (3) from the ECM.


e.

Release transmission wire from bracket (4).


f.
C413370

Unlock the connector (1) and disconnect it from the compressor with magnet clutch.


g.

Loosen clamp (2).


h.

Loosen clamp (3).


i.
A442177

Loosen the E8 bolts (1).


j.

Loosen clamp (2).


k.

Detach positive battery cable at the clamp (3).


l.

Release cable duct (4) and lay to one side.


m.
C413371

Unlock connector (1) and remove from starter assembly.


n.

Detach the cable (2) from the clamps and set it aside.


o.
C413372

Unlock the connector (1) on the automatic transmission assembly and pull off.


p.

Loosen the cables from the clamps (2).


q.

Thread out and remove the transmission wire.