Home › Engine / Hybrid System › B48 (INTAKE / EXHAUST) › TURBOCHARGER
RM3650E _51 Engine / Hybrid System _080067 B48 INTAKE / EXHAUST _0388409 TURBOCHARGER A

B48 INTAKE / EXHAUST  TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




NOTICE:
·

Electrostatic discharge.

Damage to or destruction of electrical components.

-

Only touch the housings of electrical components. Do not touch pins or multi-pin connectors directly.

-

For additional information see:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




HINT:
·

Prior to replacing the turbocharger sub-assembly: Observe the notes on troubleshooting on the turbocharger sub-assembly.

·

For turbocharger sub-assembly damage: Check the pressure pipes, charge air cooler and intake plenum for foreign matter, damage and correct functionality.

·

If the oil return line is exchanged, then the connecting pipe to the oil sump must ALWAYS be cleaned, as the connecting pipe can coke.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17882 2.REMOVE NO. 2 AIR CLEANER HOSE

Hide 85010 3.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

Hide 11271A 4.REMOVE REAR CYLINDER BLOCK COVER

Hide 82261A 5.REMOVE POSITIVE BATTERY CABLE

Hide 51219 6.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide 7.DRAIN ENGINE COOLANT (for High Temperature)

Hide 25051 8.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 17167 9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




a.
A441842

Loosen E10 bolt (1) and T30 bolt(2).


b.

Disconnect No. 1 exhaust manifold heat insulator (3) in the marked area and remove.


c.
A441843

Loosen E10 bolts (1).


d.

Remove the No. 1 exhaust manifold heat insulator (2).


Hide 15407 10.SEPARATE TURBO OIL INLET PIPE SUB-ASSEMBLY

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




a.
A441847

Loosen T30 bolt (1).

HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.



b.

Remove the turbo oil inlet pipe sub-assembly (2) from the turbocharger sub-assembly and tie to one side.


Hide 15474 11.SEPARATE TURBO OIL OUTLET PIPE

a.
A441848

Loosen T30 bolt (1).

HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.



b.

Release turbo oil outlet pipe (2) for the turbocharger sub-assembly from the cylinder block sub-assembly.


Hide 16027 12.SEPARATE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




a.
A258525

Loosen T30 bolt (1).

HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.



b.

Pull off the No. 1 turbo water pipe sub-assembly (2) for the turbocharger sub-assembly, lay to one side and secure.


Hide 16028 13.SEPARATE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




a.
A258526

Loosen T30 bolt (1).

HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.



b.

Remove the No. 1 turbo water pipe sub-assembly (2) for the turbocharger sub-assembly, put to one side and secure.


Hide 17201 14.REMOVE TURBOCHARGER SUB-ASSEMBLY

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




a.
A441849

Unlock plug connection (1) and disconnect.


b.
A441850

Loosen nuts in the order (5) to (1).

HINT:

Turbocharger sub-assembly is not bolted to the underside (6), but clamped instead. When removing or replacing the turbocharger sub-assembly, the clamping strip remains screwed on.



c.
A441851

Remove No. 2 turbocharger stay (1).


d.
A441852

Remove the turbocharger sub-assembly (1) in the direction of the arrow.

CAUTION:
·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person or other persons.





Hide 15474 15.REMOVE TURBO OIL OUTLET PIPE

a.
A258529

Loosen T30 bolt (1).

HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.



b.

Remove turbo oil outlet pipe (2) for the turbo charger sub-assembly.