Home › Engine / Hybrid System › B48 (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2019.03–2020.03
RM3650E _51 Engine / Hybrid System _080178 B48 ENGINE MECHANICAL _0388840 ENGINE ASSEMBLY A

B48 ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 12180E 3.REMOVE OIL FILLER CAP ASSEMBLY

Hide 12101A 4.REMOVE OIL PAN DRAIN PLUG

Hide 12101A 5.INSTALL OIL PAN DRAIN PLUG

Hide 53450A 6.REMOVE AND INSTALL HOOD SUPPORT ASSEMBLY

CAUTION:
·

Shutting bonnet or tailgate.

Danger of injury!

-

Support hood sub-assembly/tailgate in fully open position with the aid of a suitable device.




a.
A442484

Lift clamp (3) slightly using a screwdriver, in the direction of the arrow.


b.

Lift off ball socket (1) from ball pin (2).


c.

Repeat the operation on the other side of vehicle.

HINT:

Conduct the following operation with the assistance of a second person.



d.
A442485

Remove the hood support assembly and open the hood sub-assembly further.


e.

Push special tool 0 493 647 (51 2 170)(3) over gas pressure spring (1).

SST
09800-WA030  


f.

Position the special tool 0 493 647 (51 2 170) on the ball pin (2) and apply force to engage it.

SST
09800-WA030  


g.

Repeat the operation on the other side of vehicle.


Hide 85010 7.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

Hide 53383 8.REMOVE HOOD TO COWL TOP SEAL

a.
A446747

Feed the cable out from the brackets to the front in the marked area.


b.

Remove the hood to cowl top seal (1) inward from the guide.


Hide 53681 9.REMOVE UPPER FRONT SUSPENSION CENTER BRACE

NOTICE:

Driving without upper front suspension center brace is not permissible.


a.
A442472

Remove E14 bolts (1) and bolts (2).


b.

Remove the upper front suspension center brace (3).


Hide 55788A 10.REMOVE COWL TOP VENTILATOR LOUVER PROTECTOR

a.
A442473

Loosen bolts (1).


b.

Remove the cowl top ventilator louver protector (2).


Hide 55789B 11.REMOVE NO. 2 COWL TOP VENTILATOR LOUVER PROTECTOR

a.
A442480

Loosen bolts and nut (1).


b.

Remove the No. 2 cowl top ventilator louver protector (2).


Hide 12601B 12.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

NOTICE:
·

Damage to the No. 1 engine cover sub-assembly.

Jerky movements during disassembly and excessive application of force during installation may result in breakage of the No. 1 engine cover sub-assembly.

-

Disassemble or mount the No. 1 engine cover sub-assembly carefully.

-

Disassemble or mount snap-lock couplings of the ball pivots one after the other.

-

Disassemble or mount No. 1 engine cover sub-assembly only at temperatures >20 °C.

Vehicle information / Control unit list / DME / Call up control unit functions / Diagnostic request / Diagnostic request / 117 Ambient temperature

-

Use only distilled water as an auxiliary material during installation, no lubricants.




a.
A445287

Unclip the No. 1 engine cover sub-assembly (1) from the holders in the indicated area towards the top.


Hide 11271A 13.REMOVE REAR CYLINDER BLOCK COVER

a.
A442482

Unclip the rear cylinder block cover (1) at the grommets (2) and remove it toward the top.


Hide 14.REMOVE POSITIVE BATTERY CABLE

a.
A441478

Unlock the locks (1).


b.

Guide and remove cover (2) in direction of arrow.


c.
A442133

Unfasten nut (1).


d.

Loosen clamp (2).


e.

Feed out generator wire (3) and put to one side.


f.
A442127

Unfasten nut (1).


g.

Loosen clamps (2).


h.

Feed out starter wire (3) and put to one side.


Hide 15.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A441939

Unclip the lines in the marked areas.


b.

Loosen E8 screws (1).


c.

Remove wire harness clamp bracket (2) for the generator wire.


Hide 17.REMOVE ENGINE ROOM ECM BOX

a.
A442173

Unlock and loosen locks (1) and (2).


b.

Release the wiring harnesses from the engine room ECM box and set it aside.


c.
A444836

Unlock plug connection (1) and disconnect.


d.
A444837

Unlock and loosen the 3 clamps (marks).


e.
A442174

Loosen bolts (1).


f.

Guide out and remove the engine room ECM box (2).


Hide 82161 18.REMOVE FLOOR WIRE

a.
A441940

Unclip floor wire (1) for the voltage supply of the power distribution box in the marked area.


b.

Set aside the floor wire (1) for the voltage supply of the power distribution box.


Hide 44764G 19.DISCONNECT CONNECTOR TO BRAKE BOOSTER TUBE

a.
A441947

Unlock, disconnect and tie the connector to brake booster tube (1) to one side.


Hide 23827A 20.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A441946

Disengage the clamp.


b.

Unlock, disconnect and tie the No. 2 fuel vapor feed hose (1) to one side.


Hide 53826A 21.REMOVE FRONT UPPER FENDER PROTECTOR LH

Hide 53825A 22.REMOVE FRONT UPPER FENDER PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 53205 23.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 17880 25.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 23802B 27.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 17882 28.REMOVE NO. 2 AIR CLEANER HOSE

Hide 11401T 29.REMOVE CYLINDER BLOCK COVER

Hide 51219 30.REMOVE FRONT SUSPENSION MEMBER LOWER PROTECTOR

Hide 31.DRAIN ENGINE COOLANT (for Low Temperature)

Hide 32.DRAIN ENGINE COOLANT (for High Temperature)

Hide 34.DISCONNECT WATER HOSE

HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.


a.
A442312

Unlock, disconnect and tie the No. 1 radiator hose (1) and (2) to one side.


b.
A442351

Unlock, disconnect and tie the heater water hose (1) and No. 1 water by-pass hose (2) to one side.


c.

Unlock and disconnect the No. 5 water by-pass hose (3) in the marked area.


d.

Unclip the No. 5 water by-pass hose (3) in the marked area.


e.

Unlock, disconnect and tie the radiator reserve tank hose (4) in the marked area to one side.


f.
A442350

Unlock, disconnect and tie the No. 7 water by-pass hose and No. 6 radiator hose (1) to one side.


Hide 28100 35.REMOVE STARTER ASSEMBLY

Hide 25051 36.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 58166A 37.REMOVE FRONT FLOOR COVER LH

Hide 58165C 38.REMOVE FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 58151 39.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

Hide 45.SEPARATE OIL COOLER TUBE

a.
A442317

Loosen T25 screw (1).


b.

Loosen the No. 1 automatic transmission oil cooler tube clamp (2).


c.

Tie the oil cooler tube to the side.


Hide 88710 46.REMOVE AIR CONDITIONING TUBE ASSEMBLY

a.
A446753

Loosen T45 bolts (1).


b.

Remove air conditioning tube assembly (2) upwards.


Hide 88707 47.REMOVE SUCTION PIPE SUB-ASSEMBLY

a.
A446752

Loosen T45 bolts (1).


b.

Remove suction pipe sub-assembly (2) upwards.


Hide 48.REMOVE ENGINE ASSEMBLY

CAUTION:
·

Components connected to the engine joint or cross member.

Danger of injury!

-

Check lifting eyes and engine mounting brackets for damage, e.g. cracks.

-

Attach the component to correctly mounted engine joints or cross members only.

-

Exclusively lift the component, do not move it forwards, backwards or in transverse direction.




a.
A441445

Guide in and position special tool 2 459 012 on cylinder head.

SST
09200-WA610  


b.

Tighten the bolts (1) of special tool 2 459 012.

SST
09200-WA610  

Torque:
21.5 N*m (219 kgf*cm, 16 ft.*lbf)


c.
A441382

Connect both hooks (1) and (2) of the special tool 0 490 561 (11 0 000) to the front and back of the engine with the engine hangers.

SST
09200-WA870  

HINT:

The workshop crane, lifting gear and the engine hangers on the engine must all be connected to each other so that the engine hangs straight upon lifting.



d.
A513865

Release the E14 bolt (1) from the top.


e.
A513866

Release the E14 bolt (1) from the top.


f.

Raise and remove the engine.


Hide 49.INSTALL ENGINE STAND

CAUTION:
·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.




a.
A442395

Loosen E12 bolts (1).


b.

Remove the No. 1 front engine mounting bracket RH (2).


c.
A445552

Position and secure engine stand attachment No. 1 on the engine.


d.

Tighten bolts (1).

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


e.

Lower engine slowly.


f.
A446754

Release both hooks of the special tool 0 490 561 (11 0 000) at the front and back of the engine from the engine hangers.

SST
09200-WA870