Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Harness or connector
  3. Stereo component amplifier assembly
  4. Radio and display receiver assembly

WIRING DIAGRAM


E281745E02


E281746E02


E281747E02


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Disconnect the J137 and J138 radio and display receiver assembly connectors.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A


2.CHECK VEHICLE CONDITION
  1. Check the vehicle condition.
    Result 
    Result
    Proceed to
    for 4 Speakers
    A
    for 6 Speakers
    B
    for 7 or 9 Speakers
    C



B
Go to step 6

C
Go to step 10
A


3.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J137 radio and display receiver assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH side:
    Tester Connection
    Condition
    Specified Condition
    J137-1 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J137-5 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    J147-1 (+) - M8-1
    Always
    Below 1 Ω
    J147-4 (-) - M8-2
    Always
    Below 1 Ω
    J137-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    J137-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    J147-1 (+) - Body ground
    Always
    10 kΩ or higher
    J147-4 (-) - Body ground
    Always
    10 kΩ or higher
    for LH side:
    Tester Connection
    Condition
    Specified Condition
    J137-2 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J137-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    J149-1 (+) - N10-1
    Always
    Below 1 Ω
    J149-4 (-) - N10-2
    Always
    Below 1 Ω
    J137-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    J137-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    J149-1 (+) - Body ground
    Always
    10 kΩ or higher
    J149-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


5.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

6.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J137 and J138 radio and display receiver assembly connectors.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH side:
    Tester Connection
    Condition
    Specified Condition
    J137-1 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J137-5 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    J147-1 (+) - M8-1
    Always
    Below 1 Ω
    J147-4 (-) - M8-2
    Always
    Below 1 Ω
    J138-1 (RR+) - O1-1
    Always
    Below 1 Ω
    J138-3 (RR-) - O1-2
    Always
    Below 1 Ω
    J137-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    J137-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    J147-1 (+) - Body ground
    Always
    10 kΩ or higher
    J147-4 (-) - Body ground
    Always
    10 kΩ or higher
    J138-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    J138-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH side:
    Tester Connection
    Condition
    Specified Condition
    J137-2 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J137-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    J149-1 (+) - N10-1
    Always
    Below 1 Ω
    J149-4 (-) - N10-2
    Always
    Below 1 Ω
    J138-2 (RL+) - O7-1
    Always
    Below 1 Ω
    J138-6 (RL-) - O7-2
    Always
    Below 1 Ω
    J137-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    J137-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    J149-1 (+) - Body ground
    Always
    10 kΩ or higher
    J149-4 (-) - Body ground
    Always
    10 kΩ or higher
    J138-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    J138-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


8.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 9
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

9.INSPECT REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly (Click here).

  1. Inspect the rear No. 1 speaker assembly (Click here).
    Result 
    Result
    Proceed to
    OK (for Column Shift Type)
    A
    OK (for Floor Shift Type)
    B
    NG
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

10.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  3. *3: for 9 Speakers
  1. Disconnect the J137 and J138 radio and display receiver assembly connectors.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Disconnect the J150 front No. 4 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector*3.

  1. Disconnect the J144 and J145 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH side:
    Tester Connection
    Condition
    Specified Condition
    J137-1 (FR+) - J145-2 (FR+)
    Always
    Below 1 Ω
    J137-5 (FR-) - J145-7 (FR-)
    Always
    Below 1 Ω
    J137-1 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J137-5 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    J147-1 (+) - J150-1 (+)
    Always
    Below 1 Ω
    J147-4 (-) - J150-4 (RI1-)
    Always
    Below 1 Ω
    J144-1 (R+) - M8-1
    Always
    Below 1 Ω
    J144-5 (R-) - M8-2
    Always
    Below 1 Ω
    J138-1 (RR+) - J145-9 (RR+)
    Always
    Below 1 Ω
    J138-3 (RR-) - J145-10 (RR-)
    Always
    Below 1 Ω
    J138-1 (RR+) - O2-3*
    Always
    Below 1 Ω
    J138-3 (RR-) - O2-2*
    Always
    Below 1 Ω
    J145-4 (WFR+) - O1-1
    Always
    Below 1 Ω
    J145-11 (WFR-) - O1-2
    Always
    Below 1 Ω
    J137-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    J137-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    J147-1 (+) - Body ground
    Always
    10 kΩ or higher
    J147-4 (-) - Body ground
    Always
    10 kΩ or higher
    J144-1 (R+) - Body ground
    Always
    10 kΩ or higher
    J144-5 (R-) - Body ground
    Always
    10 kΩ or higher
    J138-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    J138-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    J145-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    J145-11 (WFR-) - Body ground
    Always
    10 kΩ or higher
    for LH side:
    Tester Connection
    Condition
    Specified Condition
    J137-2 (FL+) - J145-1 (FL+)
    Always
    Below 1 Ω
    J137-6 (FL-) - J145-6 (FL-)
    Always
    Below 1 Ω
    J137-2 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J137-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    J149-1 (+) - J150-3 (RI1+)
    Always
    Below 1 Ω
    J149-4 (-) - J150-2 (-)
    Always
    Below 1 Ω
    J144-2 (L+) - N10-1
    Always
    Below 1 Ω
    J144-6 (L-) - N10-2
    Always
    Below 1 Ω
    J138-2 (RL+) - J145-3 (RL+)
    Always
    Below 1 Ω
    J138-6 (RL-) - J145-8 (RL-)
    Always
    Below 1 Ω
    J138-2 (RL+) - O8-3*
    Always
    Below 1 Ω
    J138-6 (RL-) - O8-2*
    Always
    Below 1 Ω
    J145-5 (WFL+) - O7-1
    Always
    Below 1 Ω
    J145-12 (WFL-) - O7-2
    Always
    Below 1 Ω
    J137-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    J137-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    J149-1 (+) - Body ground
    Always
    10 kΩ or higher
    J149-4 (-) - Body ground
    Always
    10 kΩ or higher
    J144-2 (L+) - Body ground
    Always
    10 kΩ or higher
    J144-6 (L-) - Body ground
    Always
    10 kΩ or higher
    J138-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    J138-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    J145-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    J145-12 (WFL-) - Body ground
    Always
    10 kΩ or higher

    1. *: for 9 Speakers



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Inspect the front No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


12.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 13
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

13.CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
Go to step 14
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE) 

14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Inspect the rear No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here
    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    OK (for Double Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
Go to step 16

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)

D
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
A


15.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 16
OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

16.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)