Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P2440  Secondary Air Injection System Switching Valve Stuck Open Bank1  P2441  Secondary Air Injection System Switching Valve Stuck Close Bank1  P2442  Secondary Air Injection System Switching Valve Stuck Open Bank 2  P2443  Secondary Air Injection System Switching Valve Stuck Closed Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P2440 Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
·

Air switching valve (ASV) assembly

·

Open or short in ASV circuit

·

Secondary air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver (AID)

·

ECM


The air switching valve (for bank 1) is stuck open for 7 seconds while the engine is running (2 trip detection logic).
P2441 The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip detection logic).
·

Air switching valve (ASV) assembly

·

Open or short in ASV circuit

·

Vacuum hose (ASV - pressure sensor)

·

Secondary air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver (AID)

·

Open or short in air pump heater circuit

·

Air pump heater relay (AI-HTR)

·

Air pump assembly

·

ECM


P2442 Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
·

Air switching valve (ASV) assembly

·

Open or short in ASV circuit

·

Secondary air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver (AID)

·

ECM


The air switching valve (for bank 2) is stuck open for 7 seconds while the engine is running (2 trip detection logic).
P2443 The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip detection logic).
·

Air switching valve (ASV) assembly

·

Open or short in ASV circuit

·

Vacuum hose (ASV - pressure sensor)

·

Secondary air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver (AID)

·

Open or short in air pump heater circuit

·

Air pump heater relay (AI-HTR)

·

Air pump assembly

·

ECM



HINT:

Air switching valve normal operation:

When the Air Switching Valve (ASV) is open, exhaust gas pulsation occurs in the secondary air passage.

When the ASV is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor connected to the ASV of the Secondary Air Injection (AIR) system.

If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and stores a DTC:

·

Exhaust gas pulsation is detected by the pressure sensor despite the ECM commanding the ASV to close.

·

Exhaust gas pulsation is not detected by the pressure sensor despite the ECM commanding the ASV to open.


MONITOR STRATEGY

Related DTCs P2440: Air control valve stuck open
P2441: Air control valve stuck closed
P2442: Air control valve stuck open
P2443: Air control valve stuck closed
Required Sensors/Components (Main) Pressure sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous: P2440 Case 2, P2442 Case 2
Once per drive cycle: Others
Duration 2 seconds: P2440 Case 2, P2442 Case 2
7 seconds: Others
MIL Operation 1 driving cycle: P2440, P2442
2 driving cycles: Others
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (Knock Sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0500 (Vehicle speed sensor)
P106B (Evap. emission control system Pressure Sensor - Air Injection System Pressure Sensor correlation)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2431, P2432, P2433, P2435, P2436, P2437, P2438 (Secondary Air Injection System Pressure Sensor)

P2440 (Case 1), P2441, P2442 (Case 1), P2443
Battery voltage 11 V or more
Atmospheric pressure 45 kPa (338 mmHg) or more
Engine Running
AIR monitor during AIR: ON*1 Completed
AIR monitor during AIR: OFF*2 Completed
AIR injection driver fail (open/short or out of range) Not detected
AIR pressure sensor fail (open/short or out of range) Not detected

*1: AIR monitor during AIR: ON -
Time after AIR in operation 5 seconds or more
AIR pump ON
AIR valve Open
Engine speed 400 to 3750 rpm
Intake air amount Less than 100 gm/s
Time after engine start 1 second or more

*2: AIR monitor during AIR: OFF -
Time after AIR in operation 10 seconds or more
AIR pump OFF
AIR valve Close
Engine speed Below 3000 rpm
AIR monitor during AIR: ON Completed
Time after engine start 1 second or more

P2440, P2442 AIR valve is stuck open (Case 2)
One of the following conditions is met (a), (b) or (c)
(a) Cumulative intake air amount 100 gm/s or more
(b) Difference between starting temperature and current temperature 10°C (18°F) or higher
(c) Starting coolant temperature 60°C (140°F) or higher
AIR pump OFF
AIR valve Close
Engine speed 3750 rpm or less
AIR pressure sensor fail (open/short or out of range) Not detected
Time after engine started 1 second or more
Time after AIR in operation 10 seconds or more
AIR valve open stuck Not detected
AIR pressure sensor open stuck (DTC P2445, P2447) Not in operation
Engine load 20% or more

TYPICAL MALFUNCTION THRESHOLDS

Secondary Air Injection ON (Condition 1)
Both conditions are met during AIR ON -
Cumulative pressure pulsation 18 kPa or higher
AIR pressure 1.9 kPa or higher

Secondary Air Injection ON (Condition 2)
Both conditions are met during AIR ON -
Cumulative pressure pulsation 18 kPa or higher
AIR pressure Below 1.9 kPa

Secondary Air Injection ON (Condition 3)
Both conditions are met during AIR ON -
Cumulative pressure pulsation Below 18 kPa
AIR pressure 1.9 kPa or higher

Secondary Air Injection ON (Condition 4)
Both conditions are met during AIR ON -
Cumulative pressure pulsation Below 18 kPa
AIR pressure Below 1.9 kPa

Secondary Air Injection OFF (Condition 1)
Both conditions are met during AIR OFF -
Cumulative pressure pulsation 25 kPa or higher
AIR pressure 3 kPa or higher

Secondary Air Injection OFF (Condition 2)
Both conditions are met during AIR OFF -
Cumulative pressure pulsation 25 kPa or higher
AIR pressure Below 3 kPa

Secondary Air Injection OFF (Condition 3)
Both conditions are met during AIR OFF -
Cumulative pressure pulsation Below 25 kPa
AIR pressure 3 kPa or higher

Secondary Air Injection OFF (Condition 4)
Both conditions are met during AIR OFF -
Cumulative pressure pulsation Below 25 kPa
AIR pressure Below 3 kPa

P2440, P2442 AIR valve is stuck open (Case 1)
Either condition is met (a) or (b)
(a) AIR OFF Condition 1 Met
(b) AIR OFF Condition 2 Met

P2441, P2443 AIR valve is stuck closed
Either condition is met (a) or (b)
(a) AIR ON Condition 3 Met
(b) AIR ON Condition 4 Met

P2440, P2442 AIR valve is stuck open (Case 2)
Cumulative pressure pulsation 75 kPa or higher

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the Techstream on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the Techstream initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2440, P2441, P2442 or P2443.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.



18.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



HINT:

Determination by ECM monitoring:

The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.

The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1
Air Pump ON
Air Switching Valve Open
Pressure 1.9 kPa or more
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2
Air Pump OFF
Air Switching Valve Open
Pressure Less than 3.0 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3
Air Pump ON
Air Switching Valve Closed
Pressure 1.9 kPa or more
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4
Air Pump OFF
Air Switching Valve Closed
Pressure Less than 3.0 kPa
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5
Air Pump ON
Air Switching Valve Open
Pressure 1.9 kPa or more
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6
Air Pump OFF
Air Switching Valve Open
Pressure Less than 3.0 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7
Air Pump ON
Air Switching Valve Closed
Pressure 1.9 kPa or more
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8
Air Pump OFF
Air Switching Valve Closed
Pressure Less than 3.0 kPa
Pulsation Detection Exhaust gas pulsation not detected

If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:

The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.


HINT:
·

In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 18 to 25 kPa).

·

In case 1, the average pressure is approximately 3 to 11 kPa. The value of 1.9 kPa indicated in the table above is a threshold for detecting pump malfunctions.



Detected Condition while AIR Operating:
Air Pump ON, ASV Open
Detected Condition while AIR not Operating:
Air Pump OFF, ASV Closed
ECM Determination DTC Output
Case 1 Case 8 Normal -
Case 1 Case 6 Air switching valve stuck open P2440
or
P2442
Case 1 Case 7 Air pump stuck ON P2444
or
P2446
Case 2 Case 8 Air pump stuck OFF P2445
or
P2447
Case 3 Case 8 Air switching valve stuck closed P2441
or
P2443
Case 1 Case 5 Air switching valve stuck open and air pump stuck ON P2440 and P2444
or
P2442 and P2446
Case 2 Case 6 Air switching valve stuck open and air pump stuck OFF P2440 and P2445
or
P2442 and P2447
Case 3 Case 7 Air switching valve stuck closed and air pump stuck ON P2441 and P2444
or
P2443 and P2446
Case 4 Case 8 Air switching valve stuck closed and air pump stuck OFF P2441 and P2445
or
P2443 and P2447

HINT:
·

By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



System Check:

The pressure in the secondary air passage can be checked using the Techstream.

1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

6.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


7.

Start the engine.

8.

Perform the AIR system forced operation while the engine is idling.

9.

Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

Standard:
Tester Operation Air Pump ASV Pressure*1 Pulsation*2
AIR PUMP: ON, ASV: OPEN ON OPEN 1.9 kPa or more 18 kPa or more
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Less than 3.0 kPa Less than 25 kPa


*1: Average pumping pressure (gauge pressure). The pressure should be 1.9 kPa or more when the AIR system operates.

*2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

10.

Turn the ignition switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P2440, P2441, P2442 and/or P2443 is output A
P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output B
P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output C


If any DTCs other than P0412, P0415, P2440, P2441, P2442 and/or P2443 are output, troubleshoot those DTCs first.


A

2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMP HEATER)

B

GO TO AIR SWITCHING VALVE ASSEMBLY INSPECTION PROCEDURE (P0412 AND P0415)

C

2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMP HEATER)
a.
U151725E01
0.112,0.079 2.497,0.450 2.385,0.371 10 Front view of wire harness connector (to Air Pump Assembly) 2.593,1.428 2.916,1.570 0.323,0.142 10 D89 2.593,1.789 2.916,1.931 0.323,0.142 10 D90 2.999,1.359 3.166,1.505 0.166,0.145 10 *1 2.999,1.746 3.193,1.895 0.194,0.149 10 *2 2.002,2.683 2.894,2.845 0.892,0.163 10 *1: for Bank 1 2.002,3.018 2.894,3.181 0.892,0.163 10 *2: for Bank 2 0.339,1.157 0.787,1.320 0.448,0.163 10 APH+ 1.616,1.518 0.872,1.273 false

Disconnect the air pump assembly (for bank 1 or Bank 2) connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Tester Connection Condition Specified Condition
D89-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V
D90-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


f.

Reconnect the air pump assembly (for bank 1 or Bank 2) connector.



OK

3.INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2) (HEATER RESISTANCE)

NG

4.INSPECT AIR PUMP HEATER (AI-HTR) RELAY
3.INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2) (HEATER RESISTANCE)
a.

Inspect the air pump assembly (for bank 1 or bank 2) (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>AIR PUMP>INSPECTION).



OK

4.INSPECT AIR PUMP HEATER (AI-HTR) RELAY

NG

REPLACE AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)

4.INSPECT AIR PUMP HEATER (AI-HTR) RELAY

OK

5.CHECK AIR PUMP HEATER (AI-HTR) RELAY (POWER SOURCE)

NG

REPLACE AIR PUMP HEATER (AI-HTR) RELAY

5.CHECK AIR PUMP HEATER (AI-HTR) RELAY (POWER SOURCE)
a.

Remove the air pump heater (AI-HTR) relay.


b.
A258729E11
0.12,0.03 1.901,0.213 1.781,0.184 10 Engine Room Relay Block: 1.586,1.432 2.166,1.657 0.579,0.225 10 AI-HTR

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Tester Connection Condition Specified Condition
AI-HTR relay terminal 5 - Body ground Always 11 to 14 V


c.

Reinstall the air pump heater (AI-HTR) relay.



OK

6.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AI-HTR RELAY, BODYGROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AI-HTR RELAY, BODYGROUND)
a.

Remove the air pump heater (AI-HTR) relay.


b.

Disconnect the air pump assembly (for bank 1 or bank 2) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
AI-HTR relay terminal 3 - D89-1 (APH+) Always Below 1 Ω
AI-HTR relay terminal 3 - D90-1 (APH+) Always Below 1 Ω
D89-3 (APHG) - Body ground Always Below 1 Ω
D90-3 (APHG) - Body ground Always Below 1 Ω
AI-HTR relay terminal 3 or D89-1 (APH+) - Body ground Always 10 kΩ or higher
AI-HTR relay terminal 3 or D90-1 (APH+) - Body ground Always 10 kΩ or higher


d.

Reinstall the air pump heater (AI-HTR) relay.


e.

Reconnect the air pump assembly (for bank 1 or bank 2) connector.



OK

7.INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
a.

Inspect the air pump assembly (for bank 1 or bank 2) (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>AIR PUMP>ON-VEHICLE INSPECTION).



OK

8.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)

NG

REPLACE AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)

8.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
a.

Visual check:

i.
A277880E03
0.094,0.042 0.854,0.385 0.76,0.344 10 true for Bank 1

A277881E03
0.094,0.083 0.802,0.281 0.708,0.198 10 false for Bank 2

Start the engine and warm it up.


ii.

Turn the ignition switch off.


iii.

Disconnect the No. 1 air hose.


iv.

Connect the Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the Techstream on.


vii.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AP and ASV operation can be selected.



viii.

Start the engine.


ix.

Perform the AIR system forced operation while the engine is idling.


x.

Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.

CAUTION:

To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.



xi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.


xii.

Check that the exhaust gas does not pulsate when the ASV is turned OFF.


xiii.

Turn the ignition switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



OK:
Air Pump Operation ASV Operation Exhaust Gas Pulsation
ON OFF Not detected
ON ON Detected




b.

Other inspection method:

The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.

Perform System Check operation under Manual Mode.

*: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

i.

Start the engine and warm it up.


ii.

Turn the ignition switch off.


iii.

Connect the Techstream to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the Techstream on.


vi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.


vii.

Start the engine after the Techstream initialization is finished.


viii.

Perform the AIR system forced operation while the engine is idling.


ix.

Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream indicate the conditions shown in the table below.


x.

Turn the ignition switch off.



OK:
AIR System Operation Pulsation Condition
(ECM Calculation)
Air-Fuel Ratio
(Reference)
AIR PUMP: ON, ASV: OPEN 18 kPa or more 18 or more
AIR PUMP: OFF, ASV: CLOSE Less than 25 kPa Approximately 14.5
(around stoichiometric air-fuel ratio)


Reference:

If the air pump operation is confirmed as normal (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P2444), the air-fuel ratio detected in front of the three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.

Result
Result Proceed to
NG A
OK B


A

9.INSPECT AIR TUBE (BLOCKAGE AND LEAK)

B

16.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)
9.INSPECT AIR TUBE (BLOCKAGE AND LEAK)
A311961E03
0.177,0.031 0.958,0.229 0.781,0.198 10 false for Bank 1: 3.969,0.063 4.75,0.26 0.781,0.198 10 false for Bank 2:

a.

Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the air switching valve assembly.


b.

Inspect the air tube for blockages and damage.

OK:

No blockages in or damage to air tubes.




OK

10.INSPECT AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1 OR BANK 2)

NG

REPLACE AIR TUBE

10.INSPECT AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1 OR BANK 2)
a.

b.

Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C


A

11.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)

B

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1)

C

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 2)

11.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
A379601E01
1.594,0.854 2.021,1.115 0.427,0.26 1.552,2.969 1.979,3.229 0.427,0.26 4.75,0.844 5.177,1.104 0.427,0.26 4.708,3.115 5.135,3.375 0.427,0.26 1.604,1.823 1.302,2.052 true 1.573,3.875 1.24,4.146 true 4.427,3.948 4.271,4.323 true 5.208,1.719 5.438,2.073 true 4.5,1.729 4.344,2.031 true 5.271,3.948 5.49,4.313 true 0.625,0.104 2.948,0.49 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.677,2.24 3,2.625 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 3.865,0.094 6.188,0.479 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 3.896,2.281 6.219,2.667 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 1.677,0.906 2.01,1.104 0.333,0.198 10 false D48 0.906,2.01 1.333,2.208 0.427,0.198 10 false BATT 1.635,3.021 1.969,3.219 0.333,0.198 10 false D52 0.896,4.177 1.323,4.375 0.427,0.198 10 false BAT2 4.25,2.052 4.448,2.271 0.198,0.219 10 false E 5.427,2.073 5.698,2.292 0.271,0.219 10 false +B 4.823,0.885 5.156,1.083 0.333,0.198 10 false D50 4.792,3.156 5.125,3.354 0.333,0.198 10 false D54 4.135,4.365 4.563,4.563 0.427,0.198 10 false E2 5.448,4.354 5.875,4.552 0.427,0.198 10 false +B2

a.

Disconnect the air injection control driver (AID) (for bank 1 or bank 2) connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D48-1 (BATT) - Body ground Always 11 to 14 V (near battery voltage)
D50-5 (+B) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)
D52-1 (BAT2) - Body ground Always 11 to 14 V (near battery voltage)
D54-5 (+B2) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-1 (E) - Body ground Always Below 1 Ω
D54-1 (E2) - Body ground Always Below 1 Ω




OK

12.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

12.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
A379604E01
1.75,0.802 2.167,1.052 0.417,0.25 1.844,3.01 2.26,3.26 0.417,0.25 5,0.833 5.417,1.083 0.417,0.25 4.969,3.01 5.385,3.26 0.417,0.25 1.406,1.438 1.698,2.156 true 2.167,3.948 2.521,4.396 true 5.104,1.719 5.479,2.146 true 5.094,3.781 5.469,4.208 true 0.667,0.063 3,0.427 2.333,0.365 10 false Front view of wire harness connector: (to ECM) 0.833,2.375 3.167,2.74 2.333,0.365 10 false Front view of wire harness connector: (to ECM) 4.042,0.063 6.375,0.427 2.333,0.365 10 false Front view of wire harness connector: (to AID for Bank 1) 4.094,2.292 6.427,2.656 2.333,0.365 10 false Front view of wire harness connector: (to AID for Bank 2) 1.823,0.854 2.188,1.042 0.365,0.188 10 false D74 1.75,2.115 2.125,2.302 0.375,0.188 10 false AIRV 1.927,3.052 2.292,3.24 0.365,0.188 10 false A24 2.573,4.354 3.042,4.552 0.469,0.198 10 false ARV2 5.094,0.875 5.458,1.063 0.365,0.188 10 false D50 5.531,2.083 5.906,2.271 0.375,0.188 10 false SIV 5.531,4.188 5.906,4.375 0.375,0.188 10 false SIV2 5.042,3.052 5.406,3.24 0.365,0.188 10 false D54

a.

Disconnect the ECM connectors.


b.

Disconnect the air injection control driver (AID) (for bank 1 or bank 2) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-28 (AIRV) - D50-3 (SIV) Always Below 1 Ω
A24-43 (ARV2) - D54-3 (SIV2) Always Below 1 Ω
D74-28 (AIRV) or D50-3 (SIV) - Body ground Always 10 kΩ or higher
A24-43 (ARV2) or D54-3 (SIV2) - Body ground Always 10 kΩ or higher




OK

13.PERFORM ACTIVE TEST USING TECHSTREAM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Disconnect the air injection control driver (AID) (for bank 1 or bank 2) connector.

A379565E01
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.104,1.344 1.365,1.521 0.26,0.177 10 false SIV 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRV 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D50 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.323,1.313 4.708,1.5 0.385,0.188 10 false SIV2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARV2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D54 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


b.

Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the AIR system forced operation while the engine is idling.


h.

Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


i.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D50-3 (SIV) - D50-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D54-3 (SIV2) - D54-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D50-3 (SIV) - D50-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D54-3 (SIV2) - D54-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



j.

Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.

A379565E02
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.094,1.344 1.354,1.521 0.26,0.177 10 false SIP 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRP 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D50 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.333,1.313 4.708,1.5 0.375,0.188 10 false SIP2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARP2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D54 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


k.

Connect the Techstream to the DLC3.


l.

Turn the ignition switch to ON and turn the Techstream on.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



n.

Start the engine.


o.

Perform the AIR system forced operation while the engine is idling.


p.

Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


q.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D50-4 (SIP) - D50-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D54-4 (SIP2) - D54-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D50-4 (SIP) - D50-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D54-4 (SIP2) - D54-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V




OK

14.REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)

NG

14.REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)
a.

Replace the air injection control driver (for bank 1 or bank 2) (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL).



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


h.

Start the engine after the Techstream initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


k.

Check pending DTCs.


l.

Turn the ignition switch off.

OK:

No pending DTC output.


NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG

16.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)
OK:

No blockage and no deformation in vacuum hose.



OK

17.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)

NG

REPAIR OR REPLACE VACUUM HOSE

17.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).


e.

Check the pressure displayed on the Techstream.

Standard pressure:

45 to 135 kPa


HINT:

The Techstream displays the air pump pressure as absolute pressure.


Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

B

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1)

C

REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 2)