| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | POWER STEERING ECU ASSEMBLY | 89650 | ( )
|
- | - |
| 2 | BRACKET | - | ( )
|
- | - |
| 3 | STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY | 45020B | ( )
|
- | - |
| *A | w/ Entry and Start System | - | - |
| *1 | ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY | *2 | CLIP BAND |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Grease | - | - |
| *A | for LHD | *B | for RHD |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 18 | TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY | - | ( )
|
- | - |
| 19 | UPPER STEERING COLUMN COVER | 45286B | - | - | - |
| 20 | LOWER STEERING COLUMN COVER | 45287 | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
89650
1.INSTALL POWER STEERING ECU ASSEMBLY
|
|
| *a | Cloth | *b | Wooden Block |
|
Grease |
|
Rotate |
|
Turn | - | - |
Install the O-ring to the power steering ECU assembly.
Apply grease the power steering ECU assembly.
Apply the grease supplied with the power steering ECU assembly.
Using a 4 mm hexagon socket wrench, temporarily install the power steering ECU assembly to the electric power steering column sub-assembly with the 3 bolts.
When temporarily installing the 3 bolts to the power steering ECU assembly, do not tighten them all the way down.
Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt to the steering main shaft.
Do not apply excessive torque to the steering wheel assembly set bolt by using a tool such as an impact wrench.
The steering wheel assembly set bolt is used for turning the steering main shaft during inspection of the steering main shaft rotating torque.
Remove the steering wheel assembly set bolt after performing this inspection.
Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks.
Do not overtighten the vise, as the steering column assembly may become deformed.
Secure the power steering ECU assembly so that it is upright.
Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.
Rotate the steering main shaft 180 degrees counterclockwise and then 180 degrees clockwise at a speed of 60 rpm, and repeat 2 to 3 times to center the axis of the power steering ECU assembly. [*1]
Using a 4 mm hexagon socket wrench, tighten the 3 bolts. [*2]
Using a torque wrench, measure the turning torque of the steering main shaft.
0.9 to 3.0 N*m (10 to 30 kgf*cm, 8 to 26 in.*lbf)
Ensure that there is no abnormal resistance during rotation.
If the turning torque is not as specified, loosen the 2 bolts and repeat steps [*1] and [*2] to recenter the axis of the power steering ECU assembly.
Remove the steering wheel assembly set bolt.
2.INSTALL BRACKET
Engage the guide to install the bracket to the electric power steering column sub-assembly.
Using a 5 mm hexagon socket wrench, install the bolt.
Install the screw.
Connect the connectors and engage the clamps.
Using a new clip band to bundle the 2 wire harness together and connect them to the bracket.
45020B
3.INSTALL STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY (w/ Entry and Start System)
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45259A
8.INSTALL COLUMN HOLE COVER SILENCER SHEET
55480D
10.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
53601
11.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55317E
12.INSTALL NO. 1 INSTRUMENT SIDE PANEL
62312B
13.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
84345
14.INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
62112
15.INSTALL COWL SIDE TRIM BOARD LH
67914B
16.INSTALL FRONT DOOR SCUFF PLATE LH
58810J
17.INSTALL CONSOLE BOX ASSEMBLY
45286B
19.INSTALL UPPER STEERING COLUMN COVER
45287
20.INSTALL LOWER STEERING COLUMN COVER
24.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
25. UPDATE ECU SECURITY KEY
45130
26.INSPECT HORN BUTTON ASSEMBLY
Make sure that the horn sounds.
If the horn does not sound, inspect the horn system.
Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE
27. PERFORM DIAGNOSTIC SYSTEM CHECK
28. PERFORM POWER STEERING ECU INITIAL SETTING
30. PERFORM INITIALIZATION AND CALIBRATION
31. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
32.ADJUST STEERING CENTER