| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY | 33820B | ( )
|
- | - |
| 2 | ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY | 33820B | ( )
|
- | - |
| 3 | REAR CONSOLE BOX ASSEMBLY | 58910C | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | FRONT NO. 2 FLOOR HEAT INSULATOR | 58153 | - | - | - |
| 5 | FRONT NO. 1 FLOOR HEAT INSULATOR | 58151 | - | - | - |
| 6 | FRONT FLOOR COVER LH | 58166A | - | - | - |
| 7 | FRONT FLOOR COVER RH | 58165C | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
33820B
1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
| *a | Paint Mark | *b | Stopper |
| *c | Lock Piece | *d | Adjuster Case |
|
Install in this Direction | - | - |
Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.
Engage the guide and connect the transmission control cable assembly to the vehicle body.
Install the nut.
Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips (B).
Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.
Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (A).
Release the lock of the transmission control select cable length adjustment structure.
Twist the stopper.
Pull the lock piece outward from the adjuster case to release the lock.
Return the stopper.
Engage the 2 claws to connect the transmission control cable assembly to the floor shift shift lever assembly.
Do not forcibly pull the transmission control cable assembly into the cabin.
Connect the transmission control shift cable to the floor shift shift lever assembly.
Connect the transmission control select cable to the floor shift shift lever assembly and install the clip.
Make sure that the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.
Make sure that the transmission control select cable is securely installed.
33820B
2.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY
58910C
3.INSTALL REAR CONSOLE BOX ASSEMBLY
58153
4.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR
58151
5.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
58166A
6.INSTALL FRONT FLOOR COVER LH
58165C
7.INSTALL FRONT FLOOR COVER RH
89467C
9.CONNECT NO. 2 AIR FUEL RATIO SENSOR
|
|
|
White Tube | - | - |
57543C
10.INSTALL CENTER NO. 1 FLOOR BRACE
51447D
11.INSTALL CENTER NO. 4 ENGINE UNDER COVER
74404A
12.INSTALL BATTERY CLAMP SUB-ASSEMBLY
14.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
w/ Stop and Start System:
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/ Stop And Start System)>INSTALLATION
w/o Stop and Start System:
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/o Stop And Start System)>INSTALLATION
28800
15.INSTALL AUXILIARY BATTERY
16.INSPECT FOR EXHAUST GAS LEAK
17. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART