Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › ENGINE › 2011.08–2015.06
RM19S0E _51 Engine / Hybrid System _051450 1NZ-FE ENGINE MECHANICAL _0248069 ENGINE G

1NZ-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove air cleaner cap sub-assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).


b.

Remove the air cleaner filter element sub-assembly.


c.

Visually check that there is no dirt, blockage, or damage to the air cleaner filter element.

HINT:
·

If there is any dirt or a blockage in the air cleaner filter element, clean it with compressed air.

·

If any dirt or a blockage remains even after cleaning the air cleaner filter element with compressed air, replace it.




d.

Install the air cleaner filter element sub-assembly.


e.

Install the air cleaner cap sub-assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>INSTALLATION).


Hide 7.INSPECT IGNITION TIMING

a.

When using an intelligent tester:

i.

Warm up and stop the engine.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON and turn the tester on.


iv.

Start the engine.


v.

Select the following menu items:

Powertrain / Engine and ECT / Active Test / TC and TE1 / ON.

HINT:

Refer to the intelligent tester operator's manual for further details.



vi.

Inspect the ignition timing during idling.

Standard ignition timing:
Transaxle Ignition Timing
Manual Transaxle 8 to 12 degrees BTDC
Automatic Transaxle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, shift the transaxle to the neutral position.




vii.

Select the following menu items: TC and TE1 / OFF.


viii.

Turn the ignition switch off.


ix.

Disconnect the intelligent tester from the DLC3.



b.

When not using an intelligent tester:

i.

ii.
A116196

Pull out the wire harness (brown) shown in the illustration.

NOTICE:

After checking, wrap the wire harness with tape.



iii.

Warm up and stop the engine.


iv.

Connect the clip of the timing light to the wire harness.

NOTICE:

Use a timing light that detects the first signal.



v.
A169891E16
1.802,1.646 2.083,1.969 true 1.583,1.052 1.583,0.74 true 0.927,1.052 1.031,1.208 0.104,0.156 10 false 1 1.135,1.052 1.24,1.208 0.104,0.156 10 false 2 1.344,1.052 1.448,1.208 0.104,0.156 10 false 3 1.552,1.052 1.656,1.208 0.104,0.156 10 false 4 1.75,1.052 1.854,1.208 0.104,0.156 10 false 5 1.948,1.052 2.052,1.208 0.104,0.156 10 false 6 2.156,1.052 2.26,1.208 0.104,0.156 10 false 7 2.365,1.052 2.469,1.208 0.104,0.156 10 false 8 0.927,1.458 1.031,1.615 0.104,0.156 10 false 9 1.094,1.458 1.271,1.615 0.177,0.156 10 false 10 1.302,1.458 1.479,1.615 0.177,0.156 10 false 11 1.51,1.458 1.688,1.615 0.177,0.156 10 false 12 1.708,1.458 1.885,1.615 0.177,0.156 10 false 13 1.917,1.458 2.094,1.615 0.177,0.156 10 false 14 2.115,1.458 2.292,1.615 0.177,0.156 10 false 15 2.323,1.458 2.5,1.615 0.177,0.156 10 false 16 1.479,0.552 1.719,0.708 0.24,0.156 10 false CG 2.135,1.906 2.354,2.063 0.219,0.156 10 false TC 0.156,0.094 0.333,0.26 0.177,0.167 10 false *a

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

Text in Illustration
*a Front view of DLC3

SST
09843-18040  

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



vi.

Start the engine.


vii.

Inspect the ignition timing during idling.

Standard ignition timing:
Transaxle Ignition Timing
Manual Transaxle 8 to 12 degrees BTDC
Automatic Transaxle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, shift the transaxle to the neutral position.




viii.

Turn the ignition switch off.


ix.

Remove the timing light.



xi.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.



Hide 8.INSPECT ENGINE IDLING SPEED

a.

When using an intelligent tester:

i.

Warm up and stop the engine.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON and turn the tester on.


iv.

Start the engine.


v.

Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

HINT:

Refer to the intelligent tester operator's manual for further details.



vi.

Inspect the engine idling speed.

Standard Idling speed:
Transaxle Ignition Timing
Manual Transaxle 600 to 700 rpm
Automatic Transaxle 650 to 750 rpm


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Inspect the idling speed with the cooling fan off.

·

When checking the idling speed, shift the transaxle to the neutral position or the parking position.




vii.

Turn the ignition switch off.


viii.

Disconnect the intelligent tester from the DLC3.



b.

When not using an intelligent tester.

i.

Warm up and stop the engine.


ii.
A169891E16
1.802,1.646 2.083,1.969 true 1.583,1.052 1.583,0.74 true 0.927,1.052 1.031,1.208 0.104,0.156 10 false 1 1.135,1.052 1.24,1.208 0.104,0.156 10 false 2 1.344,1.052 1.448,1.208 0.104,0.156 10 false 3 1.552,1.052 1.656,1.208 0.104,0.156 10 false 4 1.75,1.052 1.854,1.208 0.104,0.156 10 false 5 1.948,1.052 2.052,1.208 0.104,0.156 10 false 6 2.156,1.052 2.26,1.208 0.104,0.156 10 false 7 2.365,1.052 2.469,1.208 0.104,0.156 10 false 8 0.927,1.458 1.031,1.615 0.104,0.156 10 false 9 1.094,1.458 1.271,1.615 0.177,0.156 10 false 10 1.302,1.458 1.479,1.615 0.177,0.156 10 false 11 1.51,1.458 1.688,1.615 0.177,0.156 10 false 12 1.708,1.458 1.885,1.615 0.177,0.156 10 false 13 1.917,1.458 2.094,1.615 0.177,0.156 10 false 14 2.115,1.458 2.292,1.615 0.177,0.156 10 false 15 2.323,1.458 2.5,1.615 0.177,0.156 10 false 16 1.479,0.552 1.719,0.708 0.24,0.156 10 false CG 2.135,1.906 2.354,2.063 0.219,0.156 10 false TC 0.156,0.094 0.333,0.26 0.177,0.167 10 false *a

Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.

Text in Illustration
*a Front view of DLC3

SST
09843-18040  

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



iii.

Start the engine.


iv.

Inspect the engine idling speed.

Standard Idling speed:
Transaxle Ignition Timing
Manual Transaxle 600 to 700 rpm
Automatic Transaxle 650 to 750 rpm


NOTICE:
·

Turn all the electrical systems and the A/C off.


·

Inspect the idling speed with the cooling fan off.


·

When checking the idling speed, shift the transaxle to the neutral position or the parking position.




v.

Turn the ignition switch off.


vi.

Disconnect the tachometer.


vii.

Remove SST from terminal 9 (TAC).



Hide 9.INSPECT VALVE CLEARANCE

a.

Check for noise and vibration.

i.

Check for valve noise or a rough idle.


ii.

Judge whether valve clearance needs to be adjustmented.

If the valve noise is too loud or the idle is rough, inspect the valve clearance (See page Engine / Hybrid System>1NZ-FE ENGINE MECHANICAL>VALVE CLEARANCE>ADJUSTMENT).



Hide 10.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.



e.

Disconnect the 4 fuel injector connectors.


f.
A116195

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Compression:

980 kPa (10.0 kgf/cm2, 142 psi)


Minimum pressure:

784 kPa (8.0 kgf/cm2, 114 psi)


Difference between each cylinder:

98 kPa (1.0 kgf/cm2, 14 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as short a time as possible.




iv.

If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.





g.

Connect the 4 fuel injector connectors.






Hide 11.INSPECT CO/HC

a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.


d.

Check the CO/HC concentration during idling and when running at 2500 rpm.

HINT:

When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.


If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

i.

ii.

See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problems Possible Causes
Normal High Rough idling
1.

Faulty ignition:

-

Incorrect timing

-

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leakage from intake and exhaust valves

4.

Leakage from cylinders


Low High Rough idling
(Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idling
(Black smoke from exhaust)
1.

Restricted air cleaner filter element

2.

Plugged PCV valve

3.

Faulty EFI systems:

-

Faulty pressure regulator

-

Faulty engine coolant temperature sensor

-

Faulty mass air flow meter

-

Faulty ECM

-

Faulty injectors

-

Throttle body