2.INSPECT ENGINE OIL
3.INSPECT BATTERY
17801
4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove air cleaner cap sub-assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).
Remove the air cleaner filter element sub-assembly.
Visually check that there is no dirt, blockage, or damage to the air cleaner filter element.
If there is any dirt or a blockage in the air cleaner filter element, clean it with compressed air.
If any dirt or a blockage remains even after cleaning the air cleaner filter element with compressed air, replace it.
Install the air cleaner filter element sub-assembly.
Install the air cleaner cap sub-assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>INSTALLATION).
16361A
5.INSPECT FAN AND GENERATOR V BELT
19100P
6.INSPECT SPARK PLUG
7.INSPECT IGNITION TIMING
When using an intelligent tester:
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Select the following menu items:
Powertrain / Engine and ECT / Active Test / TC and TE1 / ON.
Refer to the intelligent tester operator's manual for further details.
Inspect the ignition timing during idling.
| Transaxle | Ignition Timing |
|---|---|
| Manual Transaxle | 8 to 12 degrees BTDC |
| Automatic Transaxle |
Turn all the electrical systems and the A/C off.
Inspect the ignition timing with the cooling fan off.
When checking the ignition timing, shift the transaxle to the neutral position.
Select the following menu items: TC and TE1 / OFF.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester:
Remove the No. 2 cylinder head cover (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>REMOVAL).
Pull out the wire harness (brown) shown in the illustration.
After checking, wrap the wire harness with tape.
Warm up and stop the engine.
Connect the clip of the timing light to the wire harness.
Use a timing light that detects the first signal.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Start the engine.
Inspect the ignition timing during idling.
| Transaxle | Ignition Timing |
|---|---|
| Manual Transaxle | 8 to 12 degrees BTDC |
| Automatic Transaxle |
Turn all the electrical systems and the A/C off.
Inspect the ignition timing with the cooling fan off.
When checking the ignition timing, shift the transaxle to the neutral position.
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSTALLATION).
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
8.INSPECT ENGINE IDLING SPEED
When using an intelligent tester:
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Refer to the intelligent tester operator's manual for further details.
Inspect the engine idling speed.
| Transaxle | Ignition Timing |
|---|---|
| Manual Transaxle | 600 to 700 rpm |
| Automatic Transaxle | 650 to 750 rpm |
Turn all the electrical systems and the A/C off.
Inspect the idling speed with the cooling fan off.
When checking the idling speed, shift the transaxle to the neutral position or the parking position.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester.
Warm up and stop the engine.
Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
| *a | Front view of DLC3 |
Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Start the engine.
Inspect the engine idling speed.
| Transaxle | Ignition Timing |
|---|---|
| Manual Transaxle | 600 to 700 rpm |
| Automatic Transaxle | 650 to 750 rpm |
Turn all the electrical systems and the A/C off.
Inspect the idling speed with the cooling fan off.
When checking the idling speed, shift the transaxle to the neutral position or the parking position.
Turn the ignition switch off.
Disconnect the tachometer.
Remove SST from terminal 9 (TAC).
9.INSPECT VALVE CLEARANCE
Check for noise and vibration.
Check for valve noise or a rough idle.
Judge whether valve clearance needs to be adjustmented.
If the valve noise is too loud or the idle is rough, inspect the valve clearance (See page Engine / Hybrid System>1NZ-FE ENGINE MECHANICAL>VALVE CLEARANCE>ADJUSTMENT).
10.INSPECT COMPRESSION
Warm up and stop the engine.
Remove the No. 2 cylinder head cover (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>REMOVAL).
Remove the 4 ignition coils (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL ).
Remove the 4 spark plugs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL).
Disconnect the 4 fuel injector connectors.
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
980 kPa (10.0 kgf/cm2, 142 psi)
784 kPa (8.0 kgf/cm2, 114 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
Inspect the other cylinders in the same way.
Measure the compression in as short a time as possible.
If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.
If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION ).
Install the 4 ignition coils (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION ).
Install the No. 2 cylinder head cover (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSTALLATION).
Clear the DTC (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).
11.INSPECT CO/HC
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2500 rpm.
When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the heated oxygen sensor operation (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DATA LIST / ACTIVE TEST).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
|---|---|---|---|
| Normal | High | Rough idling | 1.
Faulty ignition: -
Incorrect timing -
Fouled, shorted or improperly gapped plugs 2.
Incorrect valve clearance 3.
Leakage from intake and exhaust valves 4.
Leakage from cylinders |
| Low | High | Rough idling
(Fluctuating HC reading) |
1.
Vacuum leaks: -
PCV hoses -
Intake manifold -
Throttle body -
Brake booster line 2.
Lean mixture causing misfire |
| High | High | Rough idling
(Black smoke from exhaust) |
1.
Restricted air cleaner filter element 2.
Plugged PCV valve 3.
Faulty EFI systems: -
Faulty pressure regulator -
Faulty engine coolant temperature sensor -
Faulty mass air flow meter -
Faulty ECM -
Faulty injectors -
Throttle body |