Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2014.07
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248087 CYLINDER HEAD GASKET A

2NZ-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.REMOVE FRONT WHEEL RH

Hide 51441C 3.REMOVE ENGINE UNDER COVER RH (for Plastic Type)

Hide 51405A 4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Hide 7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 8.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 9.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 10.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55735D 11.REMOVE FRONT AIR SHUTTER SEAL RH (for LHD)

Hide 55735D 12.REMOVE FRONT AIR SHUTTER SEAL RH (for RHD)

Hide 55722C 13.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 14.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)

Hide 55711 15.REMOVE OUTER COWL TOP PANEL (for LHD)

Hide 55711 16.REMOVE OUTER COWL TOP PANEL (for RHD)

Hide 74431 18.REMOVE BATTERY TRAY

Hide 17881 20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

Hide 16573B 22.DISCONNECT NO. 3 RADIATOR HOSE

A116580

a.

Disconnect No. 3 radiator hose.


Hide 16711 23.DISCONNECT RESERVE TANK HOSE

A116581

a.

Disconnect the reserve tank hose.


Hide 16502 24.REMOVE WATER FILLER SUB-ASSEMBLY

A116739

a.

Separate No. 1 radiator hose from the cylinder head.


b.

Remove the 2 nuts and the water filler sub-assembly.


Hide 16264 25.DISCONNECT NO. 2 WATER BY-PASS HOSE

A116740

a.

Disconnect No. 2 water by-pass hose.


Hide 16261 26.DISCONNECT WATER BY-PASS HOSE

A116741

a.

Disconnect the water by-pass hose.


Hide 22030 27.DISCONNECT THROTTLE WITH MOTOR BODY CONNECTOR

A268158

a.

Separate the wire harness clamp.


b.

Remove the nut and separate the throttle with motor body connector.


Hide 12261 28.DISCONNECT VENTILATION HOSE

A116973

a.

Disconnect the ventilation hose.


Hide 44774 29.DISCONNECT UNION TO CONNECTOR TUBE HOSE

A116744

a.

Disconnect the union to connector tube hose.


Hide 15301 30.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 17111 31.REMOVE INTAKE MANIFOLD

A268159

a.

Separate the 3 wire harness clamps shown in the illustration.


b.
A116746

Remove the 3 bolts, 2 nuts and the intake manifold.


Hide 11452 32.REMOVE OIL LEVEL DIPSTICK GUIDE

A268160

a.

Disengage the clamp and disconnect the wire harness from the oil level dipstick guide.


b.

Remove the bolt and the oil level dipstick guide.


c.

Remove the O-ring from the oil level dipstick guide.


Hide 23901 33.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 44763 34.DISCONNECT BOOSTER VACUUM TUBE

A116748

a.

Disconnect the booster vacuum tube.


Hide 11101E 35.DISCONNECT CAMSHAFT POSITION SENSOR CONNECTOR

A116749

a.

Disconnect the camshaft position sensor connector.


Hide 89422 36.DISCONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR

A116750

a.

Disconnect the engine coolant temperature sensor connector.


Hide 89465 37.DISCONNECT HEATED OXYGEN SENSOR CONNECTOR

A116751

a.

Remove the bolts and separate the sensor bracket.


b.

Disconnect the heated oxygen sensor connector.


Hide 87245A 38.DISCONNECT INLET HEATER WATER HOSE A

A116752

a.

Disconnect inlet heater water hose A.


Hide 16268 39.SEPARATE NO. 1 WATER BY-PASS PIPE

A116753

a.

Remove the bolt and separate No. 1 water by-pass pipe.


Hide 40.DISCONNECT WIRE HARNESS

A116755

a.

Remove the 2 bolts and disconnect the wire harness.


Hide 17410 41.SEPARATE FRONT EXHAUST PIPE ASSEMBLY

A116756

a.

Remove the 2 bolts and 2 compression springs and separate the front exhaust pipe assembly.


Hide 25591 43.REMOVE MANIFOLD SUPPORT BRACKET

A116757

a.

Remove the 3 bolts and the manifold support bracket.


Hide 27020 44.REMOVE GENERATOR ASSEMBLY

Hide 12261 46.DISCONNECT VENTILATION HOSE

Hide 23820 47.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 11201 48.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12305 49.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 13407 50.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

Hide 11101J 52.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 16100 54.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 12315A 55.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

Hide 13540 58.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13506 61.REMOVE CHAIN SUB-ASSEMBLY

Hide 13511 62.REMOVE CAMSHAFT

NOTICE:

When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.


a.
A035758

Using several steps, uniformly loosen and remove the 19 bearing cap bolts in the sequence shown in the illustration, and then remove No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

NOTICE:

Loosen each bolt uniformly while keeping the camshaft level.



b.

Remove the camshaft and No. 2 camshaft.


Hide 11101 63.REMOVE CYLINDER HEAD SUB-ASSEMBLY

A035286

a.

Using several steps, uniformly loosen and remove the 10 cylinder head bolts with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 plate washers.

NOTICE:
·

Do not drop the washers into the cylinder head.

·

Head warpage or cracking could result from removing the bolts in the wrong order.




Hide 11115 64.REMOVE CYLINDER HEAD GASKET

A116758

a.

Remove the cylinder head gasket.