Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2011.08–2014.07
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248177 AUTOMATIC TRANSAXLE ASSEMBLY A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 74431 3.REMOVE BATTERY TRAY

Hide 28100 8.REMOVE STARTER ASSEMBLY

Hide 10.SEPARATE WIRE HARNESS (w/ ABS)

a.
C244588

Remove the bolt and separate the No. 3 engine wire from the automatic transaxle assembly.


b.

Disconnect the park/neutral position switch connector.


c.

Disconnect the transmission wire connector.


d.

Disconnect the transmission revolution sensor connector.


e.

Disengage the 8 clamps and separate the wire harness.


Hide 11.SEPARATE WIRE HARNESS (w/o ABS)

a.
C244587

Remove the bolt and separate the No. 3 engine wire from the automatic transaxle assembly.


b.

Disconnect the park/neutral position switch connector.


c.

Disconnect the transmission wire connector.


d.

Disconnect the transmission revolution sensor connector.


e.

Disconnect the speedometer sensor connector.


f.

Disengage the 9 clamps and separate the wire harness.


Hide 14.REMOVE FRONT DRIVE SHAFT ASSEMBLIES

Hide 51201 15.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 16.SUPPORT ENGINE AND TRANSAXLE

a.
C244542

Place the wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly.

Text in Illustration
V100155

Attachment Placement Positions

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the engine assembly with transaxle is level.

·

As the engine assembly with transaxle is very heavy, be sure to support it securely.

·

To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.




Hide 11361J 17.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
U134520

Remove the flywheel housing under cover.


Hide 32101G 18.REMOVE TORQUE CONVERTER SETTING BOLT

a.
A107285E08
1.708,1.844 2.094,1.844 false 2.146,1.771 2.438,1.948 0.292,0.177 10 false SST

Use SST to hold the crankshaft pulley in place.

SST
09960-10010  (09962-01000, 09963-01000)


b.
U134521

Remove the 6 torque converter setting bolts.


Hide 12313 19.REMOVE ENGINE MOVING CONTROL ROD BRACKET

U134517

a.

Remove the 3 bolts and the engine moving control rod bracket.


Hide 12325A 20.REMOVE ENGINE MOUNTING BRACKET LH

a.
U134518

Remove the bolt and nut, and separate the engine mounting insulator LH from the engine mounting bracket LH.


b.
C181848

Remove the 4 bolts and the engine mounting bracket LH from the automatic transaxle assembly.


Hide 30500 21.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C244541

On a flat location, set the attachment in the positions shown in the illustration, and set the automatic transaxle assembly.

Text in Illustration
V100155

Attachment Placement Positions

NOTICE:

To prevent deformation of the oil pan, never set any attachments against the oil pan of the automatic transaxle assembly.



b.
C080982

Remove the 7 bolts and the automatic transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the transaxle and engine.



Hide 22.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 33403M 23.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)

a.
C193438E04
2.229,0.99 2.573,1.094 false 2.594,1.031 2.792,1.198 0.198,0.167 10 false *1

Remove the bolt and the speedometer driven hole cover sub-assembly from the automatic transaxle assembly.

Text in Illustration
*1 O-ring


b.

Remove the O-ring from the speedometer driven hole cover.


Hide 33823 25.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C107779

Remove the 2 bolts and the No. 1 transmission control cable bracket from the automatic transaxle assembly.


Hide 32921 26.DISCONNECT INLET NO. 1 OIL COOLER TUBE

a.
C244608E02
2.969,0.594 2.417,0.813 true 1.25,1.521 1.396,1.708 0.146,0.188 10 true *a 3.104,1.375 3.281,1.563 0.177,0.188 10 true *b 3.01,0.469 3.156,0.656 0.146,0.188 10 true *1

Using a union nut wrench 14 mm, disconnect the inlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.

Text in Illustration
*1 Union Nut Wrench 14 mm
*a Turn
*b Hold


Hide 32922 27.DISCONNECT OUTLET NO. 1 OIL COOLER TUBE

a.
C244609E02
2.323,1.479 2.917,1.125 true 1.198,1.865 1.385,2.031 0.188,0.167 10 true *a 3.104,1.74 3.292,1.906 0.188,0.167 10 false *b 2.958,1.01 3.146,1.177 0.188,0.167 10 true *1

Using a union nut wrench 14 mm, disconnect the outlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.

Text in Illustration
*1 Union Nut Wrench 14 mm
*a Turn
*b Hold


Hide 28.REMOVE NO. 1 OIL COOLER TUBE CLAMP

a.
U158296

Remove the bolt and the No. 1 oil cooler tube clamp from the transmission oil filler tube sub-assembly.


b.

Remove the inlet No. 1 oil cooler tube and the outlet No. 1 oil cooler tube from the automatic transaxle assembly.


Hide 35103 29.REMOVE TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY

a.

Remove the transmission oil level dipstick subassembly from the transmission oil filler tube subassembly.


Hide 35013 30.REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

C107781

a.

Disconnect the breather hose from the transmission oil filler tube sub-assembly.


b.

Remove the bolt and the transmission oil filler tube sub-assembly from the automatic transaxle assembly.


c.

Remove the O-ring from the transmission oil filler tube sub-assembly.


Hide 31.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C203923

Remove the 3 bolts and the 3 wire harness clamp brackets from the automatic transaxle assembly.